Search Documents

By Ottokar Hofmann

In tank-lixiviation, the extraction of the silver from chloridized ore by solutions of hyposulphite salts is performed by filtration. The ore-particles are kept stationary, while the solvent moves down through the mass of ore. The quickness of extraction, other conditions alike, is in direct proportion to the rapidity of the movement of the solvent through the ore. The solution, if left in contact with the ore without moving, displays but very little solving energy. If the filtration is interrupted for ten or twelve hours, and thus solution and ore are left in complete contact for that length of time, it mill be found that, when filtration is started again, the outflowing solution is but very little more saturated with silver than it was at the time of interruption, and that the ten or twelve hours were almost a perfect loss in the total time of extraction. Notwithstanding the long contact, the solution had not become saturated with silver chloride to its full solving capacity. A rapid movement of the solvent through the ore is essential to a quick extraction. This fact is well known ; and the endeavor of leachers has been to hasten extraction by increasing the rate of filtration. Siphons, vacuumpumps and other devices have been used with more or less success; but none of them have given full satisfaction. I have found that, if chloridized ore is brought into rapid contact with a proper volume of moving sodium hyposulphite solution, the silver chloride contained in the ore dissolves almost instantly, and that it is rather the volume of the solvent than its concentrated state which produces this effect. Such favorable conditions cannot be attained in tanks. The rapidity with which a certain volume of the solvent can be brought into contact with the ore-particles is limited by the speed with which the solution descends through the ore; and thus the leaching-time in tanks cannot be shortened beyond the limit set by the filteringcapacity of the ore. In a trough, however, these favorable conditions can be attained by gradually introducing the ore into the moving stream of the solvent. The ore can thus be brought into

Jan 1, 1888

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

By H. G. Doll

A new electrical logging method is described which measures the resistivity of small volumes of material near and behind the wall of the bore holes. The very small electrode systems used are supported in the face of the flexible insulator pad of appropriate dimension maintained in contact with the wall. The measurements are recorded simultaneously with two different electrode spacings. This method provides a very detailed record of the formations and particularly of the permeable beds traversed by the bore holes. The application of MicroLog to the location of permeable zones within compact formaltions, such as limestone, and to the determination of the amount of sand existing in sequences of thin shale and sand streaks is discussed. The possibility of quantitative determination, providing a step toward the evaluation of formation porosity and mud cake thickness, is also examined. Field examples illustrate the essential features of the method. INTRODUCTION In conventional electrical logging, the spontaneous potential (SP) log is used to delineate the permeable beds, and the resistivity logs are used primarily to provide indications concerning the fluid content of the beds. When the formations are much more resistive than the mud, as happens, for example, in limestone fields, the SP currents are short-circuited by the more conductive mud column, with the result that the SP log is quite rounded. In that case, the SP log generally gives the approximate location of the permeable formations but it cannot be used for an accurate determination of the boundaries of each permeable bed.' Solutions for the problem of obtaining a better determination of the permeable beds in limestone fields were developed from two angles. One approach consisted in improvements to the logging of the SP, as given by Selective SP logging and Static SP logging. These new methods, which have been described in an earlier paper,' give good results when the mud is not too salty, but they are still in a somewhat experimental stage, mostly because the development efforts have lately been concentrated on another approach to the problem, i.e., the MicroLog.

Jan 1, 1950

By L. Lü, M. O. Lai

"Mechanical alloying is a dry, high energy ball milling process which has been used to synthesize metallic powders in the solid state. The present study use this technique to synthesize Cu-base shape memory alloy powder from commercial Cu70Zn30, Cu86Zn14 and element AI powders. The evolution and formation of shape memory alloy powder were monitored using X-ray diffraction and microscopy. It was observed that shape memory alloy powder started to form after 1.8 ks of mechanical alloying. ? phase was clearly detected after 3.6 ks of mechanical alloying. The intensity of X-ray diffraction of the y phase increased when mechanical alloying duration was prolonged indicating an increase in the amount of y phase. Microstructure observation showed different stages of formation of alloyed powders: welding between powders and formation of layered structure, deformation and fracturing of layered structure, and finally the formation of alloyed powders.IntroductionMechanical alloying (MA) is a process used for producing powders with controlled and extremely fine microstructure. It was original developed in 1966 (1) to produce aNi-based superalloy combining oxide dispersion strengthening with gamma prime precipitation hardening. In recent years this technique has been used in producing a wide range of materials including intermetallic compounds (2, 3), amorphous materials (4-6) and other materials (7-9). In MA, a blend of powders is subjected to highly energetic compressive collision. The powder panicles are welded and fractured during ball milling. Therefore, it is essential that at least one of powders should be ductile to act as combiner. It has however been found that brittle components without soft element can also be mechanically alloyed (10), even ceramic powders (11).The present work aims to study the mechanism of formation of shape memory alloy powder during MA."

Jan 1, 1994

By William S. Pintz, William A. Vogely, Charles J. Johnson

This chapter on the role of minerals in developing economies is oriented toward economic policy issues. The discussion and analysis cut across the technical, economic, legal, and policy fields. The goal of this chapter is to pro- vide relevant background information important to individuals involved with the minerals sector in developing countries. Where possible, trends are shown to provide a basis for understanding the evolving role of minerals in developing economies. This chapter is divided into the following five sections: (1) characteristics of developing countries (which presents selected statistical comparisons); (2) government objectives in developing countries; (3) government policy formulation in developing countries; (4) determinants of future trends, and (5) a summary of the chapter's major points combined with the authors' view. CHARACTERISTICS OF DEVELOPING COUNTRIES There are 155 nations in the world categorized as "developing countries." In total these nations represent about one third of the value of the world's mineral production, three quarters of the world's population, and over half of the world's land surface area. The group of so-called developing countries is quite diverse and there are exceptions to almost any general observation about the group as a whole. Most definitions of the term "developing country" are based on levels of per capita income. However, if per capita income is the sole criterion used in categorization, then several oil-exporting countries would jump from the category of developing country to the category of developed country.a Obviously, this results in a poor fit with respect to other measures. In general, the majority of developing countries can be characterized by relatively low per capita income, high population growth rates, high levels of unemployment, low levels of education, short average life ex- pectancies, income distribution skewed toward the highest 20% of the population, and a large share of exports represented by primary commodities. b For the purposes of this chapter a slightly modified version of the widely used World Bank system of classification (shown in Table 1.2.1) is used. As summarized in Table 1.2.1, developing countries are divided into three main groups based on estimated gross national product (GNP) per capita. It should be noted that the high- income, oil-exporting countries have characteristics of both developing and industrialized countries; however they are included for most statistical comparisons within the group of developing countries. Of the 155 developing countries in the world, approximately half produce minerals other than common building materials, and only 32 account for more than five percent of world pro-

Jan 1, 1985

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020

By M. Kuyumcu

With annual production of almost 3.5 million metric tonnes of K20, former East Germany (GDR) was the world?s third-largest producer of potash, ranking behind only the Soviet Union and Canada. More than 80 % of production was intended for export to earn urgently needed hard currency. For this reason, beginning in the 1970s, East Germany began to mine unprofitable hard-salt sources and carnallitite fields, which are geomechanically problematic. In the course of restructuring from a centrally planned to a market economy after German reunification, only two of the nine existing potash mines were classified as economically viable for privatization. All six potash mines in the South Harz Region were closed between 1991 and 1993. The orderly safekeeping of these potash and other decommissioned ore mines and the rededication of mining areas were assigned in 1992 to a German state-owned company GVV founded especially for this purpose. Elaboration in the present documentation covers the local necessity of the type and extent of filling and safeguarding measures. As a result of the remedial measures taken, it was possible to prevent the collapse of cavities and damage to surface facilities. This documentation describes the safeguarding successes to date, with appreciable reduction and stabilization of surface settlement and with significant lessening of seismic events. Also presented are concepts updated to the state of the art for safeguarding of numerous potash mining shafts for long-term effectiveness in separation of the workings and watercourse levels in the cap rock. In the course of 100 years of production, six mining dumps resulted with a total volume of approximately 170 million m3. They consist of up to 95 % of water-soluble salts. Every year, precipitation dissolves up to 500,000 tonnes of this salt, which enters as a highly concentrated solution into watercourses and ground water. Explanation follows of measures for minimization of environmental pollution by covering of dumps and controlled drainage of alkaline solutions from the dumps. Finally, presentation is made of the results of the successful work until now by GVV for reuse of decommissioned mining sites with settlement of new companies for creation of additional jobs and for revitalization of the monostructured South Harz Potash Mining Region.

Aug 1, 2013

By S. Schutte, J. Pelders, F. Magweregwede, S. Ngobese, W. Botha

A people-centric, systematic approach that involves different stakeholders is considered necessary to successfully address changes associated with modernizing the South African mining industry. In this paper we discuss the inclusion of various South African mining industry stakeholders, particularly the employees, in equipment design and development processes. Data was acquired through a literature review and inputs from South African mining industry stakeholders through focus group discussions, interviews, and an online survey. It was suggested that some of the areas that could be improved by the inclusion of employees in the process are design quality, ergonomics, equipment acceptance by the workforce, safety, efficiency, skills, insight into context of use, and early design iterations and identification of problems. Among the issues considered to be barriers to inclusion were lack of buy-in, lack of resources, difficulty in manufacturers accessing the mines, difficulties in involving too many people, intellectual property concerns, and unavailability of mine employees due to their key responsibilities. Identified critical factors in the equipment design and development process include iterative design, stakeholder participation throughout the process, needs analysis through consultation, and change management. A guideline was developed for worker inclusion in equipment design and development that could be used by the South African mining industry. The study identified several economic and social benefits of including stakeholders in the early stages of design and development. It is recommended that the South African mining industry considers using the developed guideline.

Apr 5, 2023

Jan 1, 1967

Jan 1, 1967

By K. Swedburg, M. Samuels

"The expansion of the concentrator at New Gold’s New Afton copper-gold mine in British Columbia, Canada, completed in 2015, included an increase in the required retention time of the cleaning circuit. On site pilot testing of a Woodgrove Staged Flotation Reactor (SFR) had shown that a high grade copper concentrate would be produced with excellent recovery. The SFR was selected rather than conventional tank cell technology based on the much smaller footprint (which rendered a separate and expensive building extension unnecessary), high concentrate grades demonstrated in testing, and the lower energy requirement. Three SFRs, each capable of taking a nominal feed of 700 cubic meters per hour were installed and commissioned 10 months after the receipt of order. The SFRs operate in series and all of the cells produce a final concentrate typically grading 32% Cu, while the overall SFR stage recovery averages 55%. The tailings from the SFRs are treated in the original conventional three-stage cleaner circuit where the remaining values are recovered in a concentrate grading 28% Cu. Design production was achieved within days of the initial start-up of the SFR circuit.INTRODUCTIONThe New Afton concentrator, located near Kamloops, British Columbia, Canada processes a copper-gold ore with a designed head grade of 0.96% Cu, 0.72 g/tonne Au, and 2.22 g/t Ag.The New Afton Mine is a block cave mining operation. Ore is undercut from the bottom up and removed at the extraction level from a grid of draw points. Ore is trammed to the ore passes by underground loader and dropped to a haulage level for transport by trucks to the gyratory crusher. From the crusher, the ore is conveyed to the mill via a 4.5 kilometre long conveyor system. Block caving was chosen for the New Afton deposit because the underground infrastructure could be built below the historical open pit of the Afton Mine (a previous operation of Teck Resources) and this method is favorable to large-scale low-cost mining.The New Afton deposit is a copper-gold, alkalic porphyry system. Hypogene mineralization is characterized by discontinuous copper sulphide veinlets and disseminations, principally chalcopyrite and minor bornite, along with pyrite as the second most dominant sulphide. Gold particles vary in size from 5 µm to 40 µm and occur as native gold and electrum, associated mostly with the chalcopyrite grains and never with the pyrite. In some instances, a second alteration phase has resulted in the copper sulphides being replaced by tennantite-tetrahedrite locally and along faults that transect the mineralized body. The design head grade of arsenic is 244 PPM, although the presence of tennantite is inconsistent and can vary from trace levels to 15% of the total copper. No arsenopyrite is present in the hypogene ores. Supergene mineralization, consisting of native copper with accessory chalcocite occurs in minor amounts along faults and highly oxidized near-surface portions of the deposit."

Jan 1, 2016

Jan 1, 1971

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By Hernani Mota, Eleonardo Lucas, Christ Barriga

Este trabajo técnico presenta los estudios realizados para una caracterización física, mecánica y mineralógica del macizo y material rocoso presentes en una mina en la sierra del Perú, con énfasis en el estudio de las estructuras mineras (tajo, pila de estéril y pila de lixiviación). El principal objetivo fue determinar la influencia que tiene la alteración del pH cuando los agentes de meteorización como las condiciones climatológicas (temperatura y precipitación) someten al material y que puede causar imprevistos en las obras de ingeniería realizadas en minería.

Sep 29, 2023

By A. S. Emanuel

A correlation has been developed for calculating the phase behavior of, gas-condensate systems at reservoir conditions. The correlation is based on the principle of corresponding states and has been coded for an IBM 7094. Experimental K-values were determined for several gas-condensate systems at reservoir conditions to evaluate various semi-empirical parameters of the correlation. The approximate range of application of the correlation is 150 to 300F and 1,500 to 6,000 psi. INTRODUCTION The rapid development of digital computers during the past several years has made feasible the calculation of hydrocarbon phase behavior by methods based on rigorous thermodynamic principles. Good correlationsl have been developed for low to moderate pressures, but these techniques have not yet been extended successfully to reservoir fluids at high pressures. Consequently, the determination of phase behavior of oil and gas systems at reservoir conditions is still based almost entirely on generalized data correlations or on experimental studies of the fluid in question. While these methods have been used successfully many times, they do have inherent limitations that restrict their applicability. Generalized correlations, such as the NGShlA K-charts, are limited to the range of pressure, temperature and components for which the data were determined. The accuracy of these correlations is often questionable because the effect of total system composition is not well defined. Experimental studies offer a reliable method for determining phase behavior, but usually the studies are costly and time consuming. Recently, Leland and co-workers presented a new approach to calculating phase behavior from the principles of corresponding states.6-8 Corresponding states methods determine the thermodynamics properties of a given system by comparison with a reference substance whose properties are known. The accuracy of this approach depends on close chemical and structural similarity between the reference substance and the system in question and between components within the system itself. For high accuracy, it is usually necessary to correct for chemical and structural dissimilarities. In principle, however, the corresponding states method should be no less accurate at high pressures than at low pressures, provided reference substance properties are known. This paper describes an empirical modification of the basic correlation proposed by Leland, et al.6 for the specific purpose of calculating the phase behavior of gas-condensate fluids at reservoir conditions. The modified correlation, which has been programmed for an IBM 7094, may be used for either approximate or precise determination of fluid behavior depending on the amount of analytical and, experimental data available for the system. BASIC THEORY The basic theory of the corresponding states phase equilibria correlation was first published by Leland, Chappelear and Gamson.6 Subsequently, Leland, Chappelear and Leach published methods for improving the accuracy of the original theory.7-9 The aim of the correlation is to calculate the K-value of each component of a given system as a function of pressure, temperature, and over-all composition, where Once the K-values are known, the phase behavior may be determined directly by an appropriate flash calculation. The basic equation for calculating component K-values was taken from the work of Joffe. 4 For any component i of a mixture, the K-value is given by

Jan 1, 1969

By William Hutton Blauvelt

An official of one of the prominent iron companies of the South recently made the following statement during a discussion of the present conditions of the Southern iron business: " The trouble with us in the South has been that we have been satisfied to buy iron and coal lands, build blast-furnaces, and make pig-iron. We stopped at pig-iron, and as a result we are all poor. The South needs diversified industries, and needs to work up its raw products into articles the Southern market can use. If we had realized this sooner, some of us might now be rich." The South is awakening to this view, and in the Birmingham district alone one basic steel-mill is already in operation, and in a year&apos;s time another and much larger one will be turning out rails and shapes, with rod- and wire-mills in prospect. It is to chronicle another metallurgical step forward in the same district that I have prepared the following description of the new by-product retort coke-oven plant recently put in opera-

Jan 1, 1899

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens&apos; fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

By C. Baldwin Sawyer

J. S. Vanick,* Washington, D. C. (written discussion).—To those who have been confronted with the study of the gas-metal reactions, this paper is a most welcome contribution. My personal interest in work bearing upon this general problem, stimulated by an appreciation of the difficulties inherent to problems of this type, prompts a few words of discussion. Table 2 of the paper shows a gradual increase in the nitrogen content with an increase in pressure, and an interpretation follows in which nitrogcn is used as the compressed medium when the conditions admit that cyanogen gas could be active as a contaminating ingredient. Fusions of electrolytic iron made in the induction furnace in an atmosphere of deoxidized nitrogen and out of contact with contaminating materials have shown no microscopic evidence of -a nitrogen increase; using a refractory-lined graphite crucible in the furnace under the same conditions or admitting air often resulted in the occurrence of nitride needles in the solidified melt. These results suggested that a nitrogenous compound served as a vehicle for the introduction of nitrogen and that such compound was not available when the pure gas and carbon-free refractory were used. The fusion of pure iron in pure nitrogen is perhaps a matter of theoretical interest. The author&apos;s work serves a more practical purpose when applied to steels rather than iron. Table 2 reports the absence of nitride needles in melts made under pressure of one atmosphere, although the quantity of nitrogen present would seem to exceed microscopically detectable percentages. In some recent work29 on carburized iron, nitride needles have been observed in areas analyzing as low as 0.015 per cent. nitrogen. This low percentage of nitrogen would indicate that the solubility limit is less than 0.030 per cent. for hypoeutectoid steels. There is the possibility that the areas of pearlite which exist in a hypoeutectoid steel restrict the distribution of nitrogen and limit its presence to the ferritie fields. In view of this work and the references quoted by the author, I am led to expect that the value for the solubility of nitrogen in solidified iron may approach

Jan 1, 1924

By Keizo Uematsu, Satoshi Tanaka, Zenji Kato, Nozomu Uchida

"A novel technique is developed and applied to evaluate the binder segregated at the· surface of granule. Compressive strength of each granule was measured directly with a micro-compressive instrument. The relation between compressive characteristics and the amount of binder was discussed quantitatively.IntroductionCharacterization of granules is essential in the production of ceramics, since they govern the structure of green compact and thus the structures and properties of ceramics. However, there is no research to clarify the relation between the strength of granules and structure of granules, especially of binder segregation at granule surface. We develop a novel technique to determine the binder concentration in the granules by the iodine method. In this study, we measure yield strength of granules directly and discuss the relevance between compressive characteristics and the concentration of binder.ExperimentalGranules were prepared by spray-drying of aqueous slurry of commercial alumina (AL160-SG1. Showa Denko, Tokyo, Japan) and PVA (PVA 105 Kurare, Japan). PVA. concentration in granules was 1.1, 1.5 and 2.3 wt%. The inlet and outer air temperatures were 200 and 95 °C , respectively. Iodine-potassium iodide solution was prepared by dissolving iodine (0.15mol) and potassium iodide (0.15mol) in diluted water (50ml). A saturated boric acid solution was prepared by mixing boric acid powder with a diluted water."

Jan 1, 2000