Search Documents

By Gary B. Glass

In 1997, 92.3% or 235.7 Mt (259.8 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River coalfield. The mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft). The thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash and 19.98 MJ/kg (8,590 Btu/lb.). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coalbeds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 289 Mm3/a (10.2 billion cu ft/year). This production is occurring west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

Jan 7, 1951

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948

By Zhanjun Wang, Mei Zhang, Zuotai Zhang, Min Guo

In this study, the viscous flow and crystallization behavior of CaO–SiO2–MgO–Al2O3–FetO–P2O5–TiO2 steelmaking slags have been investigated over a wide range of temperatures. The results indicated that the viscosity of the slags slightly decreased with increasing TiO2 content. The constructed non-isothermal continuous cooling transformation (CCT) diagrams revealed that the addition of TiO2 lowered the crystallization temperatures. This can mainly be ascribed that the addition of TiO2 promotes the formation of [TiO6]-octahedra units, thereby MgFe2O4–Mg2TiO4 solid solution is formed. Moreover, the decreasing viscosity has a significant effect on the diffusion of ion units, such as Ca2+ and [TiO4]-tetrahedra, from bulk melts to crystal-melt interface. The crystallization of CaTiO3 and CaSiTiO5 was therefore accelerated, which can improve the phosphorus content in P-enriched phase.

Mar 1, 2017

By Liow Jong-Leng

A survey of the interactions of large gas bubbles formed from top and bottom injection of gases into melts was carried out. Spherical cap bubbles were found not to produce much splash when they break through the bath free surface except for that formed by plunging of the-spout at its edges. In contrast, the bursting of balloons produces cavities which give rise to liquid jets being ejected from the bath free surface. The position of the balloons relative to the bath free surface is an important parameter in the formation of the liquid jet. It is found that the interactions of multiple bubbles close to the free surface is important in determining the splash behaviour of gas injected systems.

Jan 1, 1996

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Frank C. Roberts

Progress in the facilities for handling mining products has been largely superinduced by the necessities of commercial economy ren dered requisite in order to meet the demand of competition. So rapid has been the depreciation in the value of mineral products, primarily due to the disproportionate increase of output over con sumption, that it may be justly claimed that mining, when considered as a commercial success, depends largely upon the ease and cheap ness by which the products are brought to the surface of the ground. In all methods of performing this operation, wire rope enters as an important factor; and the object of the present sketch will be to explain, as fully as is consistent with the space allotted, the various • adaptations of wire rope employed in placing coal and ores within the reach of our overground systems of transportation. These adaptations will be considered in the following order: I. Hoists. II. Inclined planes. a. Engine planes. b. Gravity planes. c. Aerial planes. III. Haulage. a. Tail-rope system. b. Counter-rope system. c. Endless-rope system. IV. Hoists. The term " hoist" is applied to the system whereby the mine product is elevated from the mine-level to the surface through ver-

Jan 1, 1888

By Nomuqhele N. Nkosi, Yasuo Yabe, Musa D. Manzi, Raymond J. Durrheim, Siyanda B. Mngadi

This study examined rock failure in brittle rocks hosting the deep gold-bearing ore bodies on scales between millimeters and kilometres. This research study is part of the International Continental scientific Drilling Program (ICDP) project, “Drilling into Seismogenic Zones of M2.0-M5.5 earthquakes in deep South African gold mines” (DSeis). The broader ICDP-DSeis project aims include the examination of the extent of damage, the stress state around the fringes of the earthquake, and the potential existence of living organisms associated with deep-level earthquakes. Nevertheless, this study focused on two seismogenic zones – the Cooke 4 mine and Moab Khotsong mine. At Cooke 4 mine, the study examined the evolution of mining-induced fractures (M1-4) occurring ahead of the stope face during the extraction of the remnant shaft pillar. These fractures were monitored and delineated by a dense array of acoustic emission sensors that allowed hypocentres to be located with decimeter accuracy. Using this acoustic emission data, the DSeis team drilled and recovered the fractures, rock breccia and gouge using a sophisticated triple-tube drilling rig.

Apr 26, 2022

By Gerrit V. R. Goodman

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 4D ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face? 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm. This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 4D ft.

Jan 1, 2010

CHEMICAL PRECIPITATION U.S. 4,067,789 - Removal of soluble manganous ions from a zinc sulfate solution formed by leaching roasted zinc sulfide ore with spent electrolyte. An excess of ammonium persulfate or like oxidant is added to the leach solution to convert manganese to insoluble, filterable gamma-manganese dioxide, and the precipitate separated from the solution by filtration. L. Harris and A. K. Hanson, Jr., assigned to Newmont Exploration Ltd. Jan. 10, 1978. 11 pp. (204-119). Filed: 5-3-76 (682.442). (Drawing on page 67.)

Jan 1, 1979

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By Aline Silva Magalhães

As elevadas taxas de encruamento nos estágios iniciais de deformação plástica observadas para os aços bifásicos constituem uma das principais características que os habilita para aplicação em componentes estruturais na indústria de automóveis. Neste trabalho foi analisada influência de tratamentos intercríticos com aquecimento em temperaturas diversas, seguido de resfriamento brusco, no comportamento em termos de encruamento de um aço bifásico, por meio de dois métodos distintos de determinação do expoente de encruamento. Observou-se que a elevação da temperatura intercrítica influenciou de modo a reduzir o valor do expoente de encruamento, dado que o aumento da temperatura reflete a elevação do percentual de martensita na microestrutura do aço. Além disso, para as diferentes abordagens aplicadas para o cálculo dos valores de n, verificou-se que por meio da técnica de linearização da curva tensão versus deformação foram obtidos valores superiores do expoente de encruamento quando comparada à abordagem utilizando o critério da estricção.

Aug 17, 2017

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011

By Q. Cui, Z. G. Song, S. S. Lin, S. Q. Li, S. S. Lu, G. B. Zheng, A. J. Ren

"Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization test studies on fluorite in tungsten beneficiation tailings and feldspar in molybdenum beneficiation tailings have been carried out by author and good test results are achieved. Some of the technologies developed in the test study have been applied in industrial productions, which have been working well. The economic, social and environmental benefits are remarkable. Our test studies and some production practices will be summarized and current situation and existing problems of comprehensive utilization for nonferrous metal mine tailings will also be discussed. Assumption and prospect for the future study on comprehensive utilization of nonferrous metal mine tailings will be brought at last.INTRODUCTION Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization of nonmetallic minerals of nonferrous metal mine tailings not only can improve the value of the ore but also reduce the stock of tailings, being the key to reduce emissions at source for exploitation of nonferrous mineral resources (Cai, Yang, 2000)."

Jan 1, 2018

By Jianbo Hu, Tao Zheng, Zhao Qihua, Rui Su

Rock mass discontinuities play a significant role in evaluating the stability of rock slopes. It is necessary to collect and analyze these discontinuities to fully understand the mechanical and deformational behaviors of rock masses. Based on the digital images of some slope faces, this paper proposes a framework based on machine learning for detecting and extracting discontinuities. First, digital images and photo poses are combined, the original scene is reconstructed, and 3D point cloud data are obtained. All captured point clouds can be mapped with each image by the direct linear transformation algorithm. Next, the detection machine learning algorithm is used to segment rock mass discontinuities on 2D digital images. Finally, based on the mapping relationship, the 2D digital images that were segmented are transformed into 3D point cloud data. The geometric parameters of the corresponding discontinuities can be extracted by the DBSCAN and the Skmeans algorithm and the characterization of specific rules. The proposed framework was evaluated utilizing a quantity of slope digital images in the Yebatan hydropower under construction, located in Sichuan Province, China, as a case study. The results illustrate that most deviations are less than 10° for the dip direction and dip angle, which verifies the reliability of the proposed framework and maintains acceptable measurement accuracy.

Nov 6, 2022

By Jos D. Weeks

On the extreme fringe of' the great Appalachian coal-basin is a long narrow detached coal-field, which is, in some respects, one of the most important in the United States. This field, about 90 miles long by 2½ to 16 miles wide, extends from the southwest corner of Somerset county, Pennsylvania, through Allegany and Garrett counties, Maryland, Mineral, Grant and Tucker counties, West Virginia, into Randolph county, West Virginia. In this distance four distinct sub-districts are recognized, the Wellersburg in Pennsylvania, the Cumberland-Georges creek in Maryland, and the Elk Garden and the Upper Potomac in West Virginia. The output of coal from the whole field including steam, domestic, smithing and coking-coal of the best quality, is about 4,500,000 tons annually. It is the nearest to tide-water of all the bituminous coal-fields which supply the great coal-markets of the Northern Atlantic seaboard ;

Jan 1, 1895

By William Campbell

In the olden days the making of alloys was an art, and the secrete of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formulæ are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,' Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville7 on the Cu-Sn series and of Shepherd 8 on the

Jan 1, 1913

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009