Search Documents

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By R. Boom

Corus Umuiden, formerly Hoogovens, was the first steel plant in Europe after Voest to introduce oxygen steelmaking. In the decision-making process contacts with Dofasco in Canada about the production of formability steel grades were crucial. In developing oxygen (LD-) steelmaking high liquid steel output rates had to be combined with accurate process control. For ingot casting static models with input control and sampling during interrupted blowing were sufficient to deliver liquid steel within the required carbon, phosphorus, sulphur and temperature windows. Computers were introduced to perform the complicated charge calculations. Continuous casting called for strict control of composition and temperature at process end point and made predictable timing crucial. Dynamic control was introduced based upon sub lance measurements and waste gas analysis. Reliable disposable measurement sensors were developed in a concerted international action. Dissolved oxygen at blow end deteriorated the quality of low carbon aluminium killed steel grades. Blowing gases through the converter bottom improved process kinetics, resulting in lower carbon-oxygen products, yield increase and better phosphorus removal and generated new families of hybrid blowing processes. Introduction of secondary metallurgy facilities such as argon stirring stations, vacuum degassers and ladle furnaces relieved the demands for strict BOF end point control. Desulphurisation of hot metal became standard practice. In regions with scrap shortage hot metal desiliconisation followed by dephosphorisation, was introduced in the blast furnace cast house and hot metal transfer ladles. Later redundant converter vessels were used for pre-treatment, resulting in a two-stage process. The fundamentals of oxygen steelmaking are described and a vision on the future is presented.

Jan 1, 2004

By Thomas E. Marshall, Gerald L. Finfinger

The Bureau of Mines has developed a practical methodology for deter- mining occluded gas contents of domal rock salt samples. The method, which is portable and field worthy, provides results in 5 min or less and does not require a laboratory environment or specially trained personnel to obtain meaningful results. The results can be used to identify gas-enriched zones, and thus may aid mine operators in production planning or ventilation design. The test method is based on the relationship between gas content and the acoustic response of salt samples as they are dissolved in water. The relationship is defined by an equation, and the results are repeat- able. The equation was derived by testing a series of rock salt samples collected from domal salt mines in Louisiana.

Jan 1, 1987

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing mischmetal (MM), cobalt, copper, magnesium, and iron for use in permanent magnets in place of the scarce samarium-cobalt alloys. The magnetic properties of MM-Co, MM-Co-Cu, MM-Co-Cu-Mg, and MM-Co-Cu-Fe-Mg alloys were evaluated. Magnets were fabricated by powder metallurgy consisting of arc-melting the metals, crushing and grinding the resultant alloys, alining and compacting the powder, and sintering the compacts. Magnetic values of MHc = 4.7 kOe, BHc = 4.07 kOe, Br = 6.81 kG, and (BH)max = 10.0 MGOe were obtained with a MM-Co alloy containing 36±0.5 wt-pct MM. By substituting copper and magnesium for part of the cobalt, the values for MHc and BHc were increased to 29.0 kOe and 5.89 kOe, respectively. This intrinsic coercivity value exceeded that of Sm-Co alloy obtained in our laboratory. The addition of iron to MM-Co-Cu-Mg alloys resulted in an increase of Br to 6.90 kG and (BH)max to 10.3 MGOe. Copper and magnesium contents of these alloys were optimized to obtain maximum values of MHc.

Jan 1, 1981

By Henry E. Blake

Defluorination studies on refractory fluoride - bearing compounds and minerals , particularly on partly defluorinated residues from high - temperature pyrohydrolysis , required a dependable and reasonably accurate analyticalcontrol method for the analysis of fluorine . The difficulty in liberating fluorine from the fluorides of metallic elements such as aluminum, zirconium , and rare earths by steam- distillation can be largely overcome if the distillation is made from a sulfuric - phosphoric acid solution of a sodium carbonate fusion of the sample material and if the distillation temperature is maintained at about 155 ° C. The data presented in this paper show that liberation of fluorine by this method is more complete and proceeds more rapidly than by usual distillations from perchloric or sulfuric acid alone or a mixture of phosphoric and perchloric acids . Fluorine in amounts ranging up to about 140 mg can be recovered by collecting only about 300 ml of distillate . Determination of fluoride in the distillate is made by the usual thorium nitrate titration .

Jan 1, 1963

By M I. Pownceby, N Karimian, J R. Manuel, M J. Peterson

The CSIRO ore classification scheme for Pilbara ores was used as a reference frame to target recognisable ore types/textures with potentially elevated phosphorus content for detailed analysis. Particles of each individual ore texture were separated from a Brockman high-P ore and each class was characterised using methods including XRF, XRD, EPMA and synchrotron-based XAS. Results were then correlated with optical microscopy and hand specimen identification to establish any relevant associated mineralogical phases and/or textures. This represents a more systematic approach to identification of high-P ore components based on particle and goethite type and texture. The information can then provide the basis for more targeted P-removal strategies factoring in the relationship between particle/ore texture and phosphorus deportment

Sep 18, 2023

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of 4 foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with MSHA’s lower coal mine respirable dust standard (1.5 mg/m3). Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used a low pressure air generated by a blower and water pressure using a NIOSH developed foam generator. Foam property tests comprising of a bottle shake test, foam expansion ratio, and water drainage were used to classify foams. The bottle shake tests determined that the lowest concentration of foam agent to be used was approximately 1.5%. Compressed air generated foams tended to have low expansion ratios (10-19) with high water drainage. Blower air generated foams had higher foam expansion ratios (30-60) with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The different foam agents produce foams with different material properties. Results of testing eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents, while having different foam properties, seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. INTRODUCTION About one-half of U.S. underground coal is produced by longwall mining. This technique allows for mining high volumes of coal, producing significant amounts of coal mine dust. This can lead to the overexposures to longwall miners and possibly occupational respiratory diseases black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [1]. When respirable quartz is present, the mine must maintain an average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present [2]. Respirable dust samples collected by U.S. Mine Safety and Health Administration inspectors for the five-year period from 2010 to 2014 found that 5.6% (53 of 943 respirable coal mine dust samples) of the longwall operators on the tailgate side exceeded the coal mine dust standard, and 4.3% (76 of 1768 samples) of the jacksetters exceeded the standard. If silica is present, the reduced standard is implemented, meaning that 11.4% (36 of 316 respirable coal mine samples analyzed for dust) of the jacksetters exceeded the reduced standard. Only 3.8% (18 of 478 samples) of the longwall operators on the tailgate side exceeded the reduced standard [3]. Had the 1.5 mg/m3 standard been in effect during this period, non-compliant samples would have been much higher. For example, over 15% of the samples collected at the tailgate shearer operator occupation exceeded the lower standard."

Jan 1, 2017

By D. R. Hanson, H. Lawson

In this study, NIOSH researchers conducted a machine learning analysis to examine whether a model could be constructed to assess the probability of dynamic failure occurrence based on geochemical and petrographic data. Random forest, cluster analysis and dimension reduction were all applied. The objective of dimensionality reduction was to explore patterns and groupings in the data and search for relations between compositional parameters. Cluster analyses were performed to determine if an algorithm could find clusters with given class memberships and to what extent misclassifications of dynamic failure status occurred. A random forest analysis performed on data from the Pennsylvania Coal Sample Databank cross-referenced with accident data from the Mine Safety and Health Administration (MSHA) determined that 7 parameters of the 18 examined exerted the most influence on results. Cluster analysis on data after dimensionality reduction resulted in a hierarchal clustering algorithm finding four clusters, with one relatively distinct dynamic failure cluster, and three clusters consisting mostly of control group members but with a small number of dynamic failure members.

Feb 1, 2023

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as sand-cast and as heat-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brinell and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. THE demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.1 Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergranular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about-950° F., quenching in oil or in cold or boiling water, and artificially aging

Jan 7, 1925

By Valtemir Coelho Rodrigues

Nos últimos anos face a quantidade significativa de reparos gerais, parciais e emergenciais no revestimento refratário dos fornos em um curto período de tempo (média 02 fornos por ano), haviam paradas prolongadas dos fornos de cal para execução destes reparos onde era necessário prever todos os anos um alto valor para compra de cal, revestimento refratário e mão de obra de manutenção refratária. Afim de reduzir estes custos, aumentar a disponibilidade e produtividade dos fornos, foi feito um estudo e análise para detectar os problemas para serem tratados. Chegamos a conclusão que para aumentar a campanha dos fornos era necessário manter um ritmo estável de produção para evitarmos os choques térmicos no revestimento, treinamento da contratada e implantação do novo projeto para realização de limpeza dos canais o que eliminava o impacto de alavancas contra o revestimento, revisar o projeto o que mudaria a geometria e a composição de algumas peças refratárias, aperfeiçoamento dos monitoramentos do revestimento dos fornos para identificação mais rápido das ocorrências de problema de forma a permitir a aplicação de técnicas corretivas de maneira eficiente além de um intenso trabalho junto ao quadro operacional incluindo cursos e melhorias nos procedimentos que impactavam diretamente na operação correta dos fornos, além disso, melhorias significativas de manutenção contribuíram para melhor performance dos fornos de cal. É possível checar os resultados que este projeto proporcionou aumentando em 06 anos no mínimo a campanha dos fornos eliminando os reparos parciais e emergenciais realizando somente reparos gerais além da redução de custos.

Aug 17, 2017

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By Álvaro Jubera, Fabricio García, Héctor Painevilo

Esta investigación busca demostrar que la aplicación de tecnologías de la industria 4.0, permite una mejora en el control de los planes de minado en tiempo real. Este estudio presenta el uso del Control de Intervalo Corto (SIC), aplicado al cumplimiento del plan de minado en una operación a tajo abierto en el norte de Chile. Para esto, se utilizó una tecnología innovadora, llamada "TIMining Aware", que consiste en un gemelo digital que crea una representación virtual de la mina y de sus operaciones en campo, permitiendo que equipos de operaciones y planeamiento puedan monitorear la ejecución del plan en tiempo real, logrando así, reducir las desviaciones y ocasionando un mejor desempeño operativo global.

Sep 29, 2023

By D. Walton, B. Chalmers

A preferred orientation is known to occur frequently in the columnar zone of castings. This has been attributed to a preferred direction of growth. However, no satisfactory mechanism was proposed by which the preferred direction of growth led to the preferred orientation. The purpose of this work has been to establish this mechanism. It has been found that in general the observed preferred orientations only develop when the preferred directions of growth reveal themselves by dendritic growth. A mechanism based on this premise is found to be in agreement with the experimental data obtained in the course of this work. WHEN a liquid metal is allowed to solidify in a mold, it usually freezes in three stages, distinguished from each other by the size and shape of the grains. The first zone to freeze (the chill zone near the mold wall) consists of relatively fine grains that are equiaxed in shape and random in orientation. The next zone consists of crystals that are elongated in the direction of heat flow, i.e., normal to mold wall. These crystals are much larger in cross section than the crystals of the chill zone and have a very strongly preferred orientation. This is the columnar zone. The final zone, which is absent in very pure metals, is again equiaxed and randomly oriented, but usually has a much coarser grain size than the chill zone. The purpose of this study is to describe and account for the crystal size and orientation in the columnar zone. The occurrence of a preferred orientation in the columnar zone is well known, and in 1940, Greninger' suggested that it is apparently related to dendritic growth although at that time the only data were for metals with the face-centered-cubic structure. Table I shows that the direction of dendritic growth and the crystal axis that follows the heat flow direction coincide in all cases so far studied. The term "dendritic growth" is used here to represent the branched type of morphology that is characteristic of growth into supercooled melts.' In addition to the supercooling which is necessary before nucleation will occur at the mold wall, the necessary supercooling for continued dendritic growth can be provided in a mold by heat flow into the already formed solid at an interface whose Liquidus temperature is depressed by an accumula-

Jan 1, 1960

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By G. G. Campbell

Bureau of Mines research to develop an in situ retorting recovery method for oil shale has involved field testing of fracturing techniques for creating fluid-flow paths in impermeable oil shale. Electrolinking, hydraulic fracturing without and with sand propping, and explosive fracturing with a liquid explosive were tested in a 25-ft-square, five-spot pattern. These wells were drilled into oil shale at 50-to 88-ft depths near Rock Springs, Wyo. Results of the fracturing tests were evaluated by injecting air into a test well and measuring flow rates and flow profiles in adjacent test wells before and after each test. To identify points of air entry (location of fractures) in wells, flow profiles were determined by use of inflatable packers and by continuous logging with an airflow probe developed during the fracturing program. Electrolinking and hydraulic fracturing without sand propping were relatively ineffective; hydraulic fracturing with sand propping created horizontal fractures with desirable flow capacity; and fracture flow capacity was significantly increased by detonation of nitro-glycerin displaced in the natural and hydraulically induced fracture systems.

Jan 1, 1970

By N. Waters

"Nickel saprolite ores are normally mined as feed to Fe-Ni smelters or Ni matte smelting operations. The smelting processes typically require high Ni cut-off grades of approximately 1.5 to 2.2% Ni, depending on the operation. These very high cut-off grades result in a significant portion of the saprolite profile being regarded as “waste” and hence having little to no value. The Starved Acid Leach Technology (SALT) was developed to recover nickel and cobalt from nickel saprolites and Caron plant residues. Relatively small amounts of acid are applied to ground saprolites or Caron residues in order to selectively leach nickel and cobalt. The leaching is performed atmospherically under low free acid conditions. Nickel and cobalt may be recovered from the leachate as a mixed hydroxide. The mixed hydroxide may be added directly to a saprolite smelting operation or refined separately. InCoR Technologies is advancing the application of SALT at a number of sites. Bench scale testing has provided a relationship between acid addition and nickel extraction in leaching. Conceptual engineering studies have been completed by SNC Lavalin. The simplicity of the SALT technology provides the benefits of low capital and operating cost and an expected rapid ramp up to full production.INTRODUCTION The recent history of hydrometallurgical nickel laterite treatment plants has demonstrated mixed financial and operational performance. Table 1 summarizes the next generation plants built after the financial and/or technical failure of the Bulong, Cawse and Murrin-Murrin plants in Australia. The Coral Bay plants (Line 1 and 2) stand out (and now Taganito) as relatively low capital cost, simple (no acid plant, production of mixed sulfide product), and modest in scale (10, 12 and 36 kt Ni/a). However, the other plants in the list (Ravensthorpe, Ramu, Goro and Ambatovy) are all characterized by financial and technical challenges. All plants have a very high capital cost ($67,000 to $120,000 USD/annual t of Ni production). Ravensthorpe was sold by BHP Billiton after a poor startup. Ramu has had a steady ramp up but only produces mixed hydroxide for refining by others. Goro has had an extended construction period (since 2001), is high cost and has been very slow to ramp up to design production rates. Ambatovy has had a steady ramp up."

Jan 1, 2017