Search Documents

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

By P. W. Hunter

The construction of a major sewerage scheme requiring 15.3 km of 5.5m excavated diameter tunnel in basalt, mixed and soft ground has been undertaken by the Melbourne and Metropolitan Board of Works. A double shielded Tunnel Boring Machine was selected to excavate 13.7 km of basalt and mixed ground. Advanced methods for recording operational data on the TBM were introduced. Progress to date has shown that the TBM can excavate rock very effectively with a best weekly production of 178.8m; soft ground has been encountered and successfully handled.

Jan 1, 1987

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

Samples weighing 0·5 g are fused with potassium hydrogen sulphate, leached with 4 ml. of 4 M nitric acid and diluted to 10 ml. with water. An aliquot of the clear solution is treated with EDTA, adjusted with ammonia to give a pH value between 5 and 6 treated with cyanide, ammonia, and sodium diethyldithiocarbamate then bismuth diethyldithiocarbamate is extracted with chloroform and the yellow colour is compared visually with a standard series. Alternatively, the bismuth complex may be filtered on a "Millipore" filter and subjected to x-ray fluorescence spectrometry.

Jan 1, 1971

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By Andre Panteleyev, Charels S. Ney, John M. Anderson

"Sam Goosly prospect, 22 miles southeast of Houston, B.C., was discovered in 1967 through geochemical reconnaissance. Soil sampling interpreted with respect to an east-to-west ice movement led to drilling targets.Mineralization is in a window of rocks thought to be Hazelton Group surrounded by Tertiary volcanic rocks and intruded by two stocks separated by about one mile. A westerly quartz monzonite stock is dated 61.1 m.y. and an easterly gabbro-monzonite complex is dated 52.5 m.y. The Tertiary volcanics are trachyandesites shown by the B.C. Department of Mines and Petroleum Resources to be in part extrusive equivalents of the gabbro, and they overlie Hazelton rocks uncomformably. Copper-molybdenum mineralization is sparsely developed in the westerly stock. Silver-copper mineralization forms an elongate west-dipping slab between the stocks in Hazelton rocks, which are continuously pyritized. The gabbro stock is not mineralized, but some dikes related to it are slightly so. Tertiary rocks are pyritized, but are not known to carry copper-silver mineralization. Hazelton rocks are divided into a lower conglomerate, an intermediate pyroclastic unit and an upper mainly sedimentary unit. They form a west-facing homocline. Coppersilver mineralization resides in the pyroclastic unit, mainly in a massive dust tuff through which are lenticular units of lapilli tuff. Well-mineralized rock is typically a breccia of light fragments in a dark chlorite-sulphide matrix. Sulphides are pyrite, chakopyrite and locally pyrrhotite, with very minor tetrahedrite, s phalerite and other sulphosalts. Rock alteration is predominantly a pervasive pyrite-sericite type, with widespread tourmaline, scorzalite, gypsum, ankerite and traces of fluorite. The most evident control of the copper-silver mineralization is the gross parallelism, over a strike length of 1.5 miles, to Hazelton strata, particularly a massive dust .tuff unit. In detail, mineralization crosscuts bedding and there is no appreciable banding within sulphides . A strictly syngenetic origin is untenable, but some initial concentration in a volcanogenic environment with subsequent modification by thermal processes seems likely."

Jan 1, 1972

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By D. W. Jahn

Road construction in the near future will require contractors to guarantee that a project will remain trouble free for years after the project has been completed. These guarantees will challenge aggregate producers to become technically proficient in judging performance of their products. Testing procedures are described that may be used to predict performance of concrete and asphalt pavements before being committed into a construction project, and may also be used as quality assurance tools during construction to monitor performance as construction proceeds.

Jan 1, 1995

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

Process plant modeling in the computer environment has been developed over the past 40 years by implementing the comminution models formed by the Julius Kruttschnitt Mineral Research Centre, University of Queensland, in the early 1970s. The models for the other processes in a mine value chain, such as blast fragmentation and flotation, were continuously developed and improved in parallel as well. Other research and commercial entities have also developed process modeling methodologies in the computer environment, which evolved as specialized commercial software or through equations set up in Excel spreadsheets. These were performed on a local computer, in thousands of simulations over a long period of time due to hardware limitations and the lack of a fully automated process. This limits the application of detailed process simulations for scale-up and strategic planning analysis, as they require many simulations to cover all possible scenarios which would take a lifetime when using local computers. The Integrated Extraction Simulator (IES), as the next generation of cloud-based software package, has made it possible to run simulations on the entire operation value chain in the same platform, including drilling and blasting, crushing, grinding, flotation, and other downstream process and material-handling units. This capability has allowed IES to handle multivariable simulations across the mine value chain, including pre-concentration and in-pit size reduction, and modify the process simultaneously.

By M. J. O'Hara

El diseño de taludes económicos y estables es una técnica que se aplica en el minado superficial que va desde la exploración hasta el final de las operaciones de extracción y reforestación. Las especialidades que conforman esta técnica son: geología estructural, mecánica de rocas, mecánica de suelos, sismología y matemáticas. En ese sentido, el presente texto describe el estado actual en que se encuentran estas ciencias aplicadas y sus limitaciones para ofrecer soluciones confiables en el diseño de taludes.

Jan 1, 1972

By Juan José Retamozo Padilla

El presente texto señala los beneficios de la gestión en salud ocupacional a través de NATCLAR, empresa con estándares OIT (Organización Internacional del Trabajo) de Gestión de Salud Ocupacional y Competencias Laborales del Perú. En este sentido, el estudio de causalidad de los riesgos o accidentes de trabajo nos derivará a causas inmediatas y básicas, las cuales se dividen en factores personales y de trabajo, para así identificar peligros y evaluar los riesgos directamente relacionados a la salud de los trabajadores por grupo ocupacional. Asimismo, contribuir con la empresa para evitar problemas legales, laborales y en beneficio de la salud del trabajador a partir de una adecuada planificación de perfiles de evaluaciones médicas específicas y finalmente, contribuir a la maximización de la productividad de los trabajadores a través de un programa de recuperación física para las personas con alteraciones anatómicas.

Sep 14, 2009

By J. D. Miller

The fossil resins of certain western coals are of significance and of sufficient value as a chemical commodity to justify a fossil resin industry. At the present time these valuable fossil resin resources, worth more than $0.50/lb as a chemical commodity, are being burned as fuel for electric power generation. This waste of our fossil resin resources corresponds to a loss in revenue of $200 million per year -equivalent to the value of the coal itself! Improved process technology for the recovery of fossil resin is under development and includes selective flotation of fossil resin from fine coal streams and solvent refining of the fossil resin flotation concentrate to produce a premium resin product. The most recent developments in process technologies are discussed with respect to separation efficiency and product quality. It is clear that the development of a fossil resin industry should not be limited by process technology.

Jan 1, 1994

By M. S. Azun

I do not at all agree with the basic points of the author's conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey's lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author's paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [Ir(1) I > Za/2 N1/2] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [p (h) = T 1ih , h>1 ,] The Markovian model for the other second order properties of ReV are also derived. [T veß], in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV's. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semivariogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 1, 1986

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By O. D. Khmelnitskaya

The research on selecting of an efficient technology of pyrite cinders complex treatment, sulfuric acid production wastes, have been made. The grades in the initial product were 2.04 g Au/t, 35.0 g Ag /t, 0.38%Cu, 1.1% Zn. Laboratory tests on cyanide technology, thiourea and sulphite leaching were carried out. Magnetic and flotation beneficiation and biohydrometallurgical technology were tested. After considering the results of the tests, the most economically efficient technology of pyrite cinders complex treatment with cyanide leaching of precious metals was determined. The technology involves water washing of soluble copper and zinc compounds, lime treatment and cyanide leaching of gold and silver, detoxification and utilization of mineral wastes. The precious metals are recovered from solutions by cementation onto zinc. Copper is recovered from rinse waters by SW/EW and then zinc is precipitated as hydroxide. All the solutions and organic agent are used in recirculation and therefore the technology is practically waste-free. Mineral wastes can be used as iron-containing materials for cement industry. The technology has been tested in pilot-plant scale under continuous operation with complete re-circulation of cyanide solutions. In this process recovery of 54% Au, 45% Ag, 30% Cu and 50% Zn has been achieved.

Jan 1, 2014

By J. Githiria, C. Musingwini, J. Muriuki

"The maximization of net present value (NPV) is a primary objective in open pit mine planning processes. In an attempt to meet this objective, cut-off grades are considered in all the stages of mining. There are three stages involved in resource extraction, namely mining, processing, and refining/marketing, which are all defined in Lane’s approach. Using Lane’s approach, the economics involved in each stage are identified independently and interact to provide an optimum cut-off grade.A hypothetical block model is used to illustrate how a computer application (Cut-off Grade Optimiser) that was developed in this study is used in the optimization of cut-off grades using Lane’s algorithm. This paper analyses the application of Lane’s approach for a single element in cut-off grade optimization as applied in the calculation of the optimum cut-off grade through a computer-aided application.Although Lane’s approach is not complex it is not widely applied to maximize the NPV of mining operations as the iterative calculations can be lengthy. The computer application developed in this study shows how Lane’s algorithm combined with a linear programming function can optimize cut-off grade with regard to the complex situations faced by mining operations. The application saves users from performing otherwise lengthy, iterative calculations.Background and previous researchAn open pit mining complex constitutes multiple pits, ore processing streams, and metal refining options. An open pit mine produces ore (valuable) and waste material. Ore is transported to an appropriate processing stream for producing concentrate. A refinery processes the concentrate to produce marketable metal product (Lane, 1964, 1988).Cut-off grade optimization is based on Lane’s theory, where a mining system consists of three major stages such as mining, milling, and refining. In this approach the cut-off grade selection is done between six cut-off grades that involve all stages of a mining operation. Selection of the optimum cut-off grade influences the net present value (NPV) by maximizing the net cash flows from the operation."

Jan 1, 2016