Search Documents

By T. L. Joseph

BLAST furnaces are most efficient thermally when the C02 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyères, is converted later to C02 depends upon the ratio of ore to coke in the charge and the degree to which C02, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + C02 = 2C0. About 300 to 400 lb. of carbon1 per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower C02 in the top gas. Riche has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher C02 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen enter-

Jan 1, 1936

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By B. Gorain, O. A. Bascur

"The advent of digital revolution has now enabled us with numerous tools that could be leveraged to transform our operational data into actionable insights. Key opportunities with digitization include better visualization, transparency, integrated planning and execution for value-chain optimization, that results in smarter production, intelligent response to changes in ore, process and equipment conditions, reduce energy and waste along with prevention of asset breakdown, safety and environmental issues. It is important to realize that these digital tools have limited value, from a metallurgical operational context, if we cannot bring-in the appropriate domain expertise along with getting the basics right. The focus within Barrick is to ensure that there is adequate depth of different disciplines built into our platforms along with breadth to integrate other disciplines such as geology and mining for an effective Mine-to-Mill integration. A gold recovery improvement strategy based on optimal Gaudin size distribution, leaching performance monitoring and guidance via feed grade maps is discussed. Simultaneous identification of process and equipment constraints enable finding the best overall conditions for Gold recovery. This paper discusses the methodology, findings, and challenges in the ongoing journey of implementing a Metallurgy Analytics platform that evolves from being retrospectively descriptive to anticipatively prescriptive.INTRODUCTION The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stakeholders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance."

Jan 1, 2018

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

Dielectrophoresis is a separation technique that uses a non-uniform electrical field to separate particles on the basis of their permittivity. There are many areas of mineral processing that might benefit from the application of dielectrophoresis. These include: coarse removal of gangue, recovery of ultrafine particles, upgrading of flotation concentrates or simply as a laboratory analysis technique. In order to determine the potential value of dielectrophoresis to the mineral processing industry, the response of composite particles was investigated. The electrical properties of composites involve complex relationships between the shape, distribution and permittivity of the individual grains within the rock. The relationship between mineral composition and dielectrophoretic force was measured on single particles from two ore types. The results were used to populate a model that could predict the separation characteristics of the ore. The insights gained from this model separator allowed potential applications of the technology to be examined and their performance evaluated.

Sep 1, 2012

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

By Luiza Esteves

Corrosion testing was performed in white liquor from a Brazilian Kraft mill. Specimens of duplex stainless steel (DSS) and lean duplex (LDSS) were exposed at 170 °C for 30 days to simulate conditions of the digester. Corrosion rates were determined from weight loss measurements. After this exposure, the corrosion products formed on the steel surface was characterized by using scanning electron microscope (SEM) equipped with EDS, X-Ray Diffraction (XRD), and X-ray photoelectron spectrometer (XPS). EBSD can be used to quantify of basis balance phases in DSS and LDSS. General corrosion rates for UNS S32304 LDSS were higher than the UNS 31803 DSS in industrial white liquor at 170 °C for 30 days. XPS and XRD analyses indicated that the film formed after the immersion test may be consisted by Fe and Cr oxides and sulphides.

Oct 30, 2017

Planning the primary development of a mineral deposit usually is done only once during the life of a mine. As a consequence, not optimizing the primary development of a mineral deposit can cause disadvantages over the whole life of a mine and can lead to higher costs. As a contribution to an improved primary development design procedure beyond the already existing work a study of the identification and quantification of the influence of parameters on primary development based on operational data from working mining operations has been completed. Based upon such a quantification of the influence of parameters a sequenced decision model was developed, that enables to develop an initial concept for the design of the accesses from the surface based upon a few critical parameters. Such a model will not replace detailed planning work within a feasibility study, but it is intended to reduce the amount of planning efforts at an early project stage through providing information what are most likely economic solutions, based on simple rules.

Jan 1, 1997

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By E. Isokangas

A mine is essentially a series of operations, including drilling and blasting, crushing, milling, flotation, and leaching, that are interconnected and therefore interrelated, with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often causes potential economic benefits and energy savings to be missed. However, the PIO methodology is a thorough approach which considers these individual process activities within the context of the whole process. The basic principle is to optimize the process as a whole, rather than each process step in isolation from the others. Metso?s Process Technology and Innovation (PTI) group offers a global consulting service for the mining and construction industries. A significant amount of this consulting work involves process integration and optimization (PIO) studies. When conducting a PIO study, every aspect of the process is considered. In addition to drilling and blasting, transportation, handling and storage, crushing, screening, grinding, flotation, separation, and recovery, other aspects including equipment utilization and energy consumption and even greenhouse gas emissions are also included if necessary. In a PIO project, it is very important to understand what type of material is being processed at any point in time. That is, which domain or domains is the material part of? This is necessary in order to observe the effect of different ore sources (and the blending of sources) on concentrator performance. Linking the ore from the pit to the concentrator required the development of an ore tracking system. As a result, PTI developed a radio-frequency based material tracking system called SmartTag?. This system allows tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles, and finally into the concentrator. Using the SmartTag? system, definitive correlations can be made between the performance of the plant and the plant feed characteristics, including the domain from which the feed ore originated. Since its commercialization in 2007, SmartTag? has been used in the majority of PTI?s consulting projects and several permanent systems have been installed worldwide1. Successful applications of the SmartTag? system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This paper describes how the SmartTag? system is being utilized by PTI and the benefits being gained by its use in PIO projects, as well as presenting some case studies.

Jan 1, 2012

By J. C. van Dyk

In a previous study by Van Dyk, et al., (2006) and Van Dyk et al. (2006), a FactSage model was developed to understand the chemistry and interpret mineral matter transformation during a fixed bed counter-current gasification process. It was concluded that the FactSage model developed, compared with HT-XRD experimental results and that the FactSage thermodynamic modeling sup-plies insight into specific mineral reactions and slag formation. The specific value for Sasol in using FactSage, in combination with HT-XRD is that it can be used to analyze equilibrium conditions for reactions occurring between inorganic and organic materials together, as well as to provide insight into mineral transformation and slag formation. The purpose of the present study was to improve the current FactSage modeling approach, by combining specific zones in the gasification process. This can improve and speed-up the interpretation of mineral matter transformations and flow properties of reacted mineral matter in coal and assist in identifying and quantifying slag formation in the gasifier operation at temperatures not reflected by normal AFT analyses. The updated and improved FactSage model compared favorably with the original model as well as with HT-XRD results and thus will be able to supply results in a faster and more convenient manner. In the new FactSage model, supported by HT-XRD experimental findings, it is indicated that feldspar formation (including anorthite) correlated with slag formation at temperatures around 1000°C and no slag formation in the base case coal was observed in the drying and devolitilization zone, as was to be expected. Feldspar is one is the mineral species which has the lowest AFT causing the most slag-liquid formation and forms probably as a product between the SiO2, Al2O3 and Ca-containing species. In the gasification zone it was clear that slag-liquid formed at a temperature of 1000°C, with a decrease in the feldspar content. Mullite formation was also observed in the base case sample in the temperature range 1000°C and 1100°C. The decrease in the amount of SiO2 at 1100°C is related to the formation of mullite, but also that the slag-liquid phase also contains an amount of SiO2 in the molten form.

Jan 1, 2014

By H. W. Glen

The use of a personal style (mainly active voice and first person) makes technical writing more pleasant to read, and helps the writer to express his meaning clearly and to avoid many of the stylistic errors normally encountered in that type of writing.

Jan 1, 1979

By Armando Vazquez

Steel Dynamics Inc. (SDI) and Tenova Goodfellow Inc. (TGI) have successfully commissioned the first hybrid extractive/laser system for continuous and full spectrum analysis (CO, CO2, O2, H2 and H2O vapor) on two twin shell furnaces at Butler, Indiana. NextGen® technology using off-gas analysis as a main tool for EAF practice optimization is a proven effective method for improving plant productivity. Significant benefits attributed to the NextGen® system are operational cost reductions through the use of real-time dynamic control of chemical energy and improved environmental conditions through reduced GHG emissions. Additionally, the implementation of Tenova’s Water Leak Detection Technology® has shown results as an effective tool for operators to identify in real-time the presence of water during both reducing and oxidizing conditions. This paper will include project details, trials and results and will also outline the latest hardware developments and multipoint capabilities

Oct 30, 2017

By Colleen A. M. Gibbs

On July 30, 1979 New Council on Environmental Quality (CEQ) regulations for implementing the procedural provisions of the decade-old National Environmental Policy Act went into effect. These new regulations replace approximately seventy different sets of agency regulations, providing some uniformity throughout the Federal government in the conduct of environmental reviews and preparation of environmental impact statements (EIS). This attempt by the Federal government at a general improvement in the preparation and quality of EIS's presents an opportunity for the mining industry to evaluate how the EIS process for mining proposals can be expedited. The environmental impact statement is often a key element on the critical path of a major mining project. Preparation of the EIS is ordinarily the responsibility of the Federal agency with primary decision-making authority over the project. Still, the proponent, i.e. the mining company, can play a major role in the process and have a major impact on the timeliness and adequacy of the effort. Typically, the Proponent will conduct (or will hire consultants to conduct) environmental baseline studies of, for example, air quality, wildlife, geology, water quality, vegetation and archaeology. These studies are then compiled into an environmental report and submitted to the agency. The agency verifies the data and incorporates them into the environmental impact statement.

Jan 1, 1979

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By O. C. Ralston

The use of copper sulfate for improving the flotation behavior of sphalerite is probably at least 15 years old. The original discovery of its activating influence is somewhat obscure. The story goes that in the mill at Mascot, Tenn., its favorable action was discovered by accident, early in 1914, as follows: The original laboratory test work on a sphalerite ore gave favorable flotation results, but after a mill had been built the flotation concentration of the ore was very unsatisfactory. In diagnosing the probable reasons, one fact pointed out was that the laboratory test machine had been constructed of bronze whereas the commercial machine allowed pulp to come in contact only with wood and iron. A plate of sheet copper was hung in the flotation machine and results immediately improved. At first fanciful explanations of electrolytic and electrostatic behavior were given credence, but when the copper plate was removed and a small amount of copper sulfate substituted in the pulp an even more favorable result was obtained. Toward the end of 1914 copper sulfate was also adopted in the acid flotation circuit of the Butte and Superior Copper Co. Just who is responsible for the original discovery the present writers do not know. It seems strange that in that era of flotation litigation this discovery was not patented. While for pragmatic purposes it [nay be sufficient to know that the mere addition of copper compounds to a flotation pulp is sufficient to activate the flotation of the sphalerite, for scientific purposes it is quite desirable to know more about how the action takes place. It is the purpose of this paper to present certain evidence dealing with the mechanism of the beneficial effect. The description of the effect as activation in contradistinction to depression is now common in both the English and German languages. It makes no assumptions as to whether the zinc sulfide surfaces have been filmed with copper compounds. In fact, the principal differences of opinion expressed in the literature deal with whether there is an actual formation of CuS (or even Cu2S) on the surface of the sphalerite. Activation of sphalerite takes place in alkaline, neutral or weakly acid solutions and whereas the present day flotation of sphalerite is usually in ah alkaline solution, the early use of copper sulfate was in a sulfate solution.

Jan 1, 1930

By J. M. Minguet

El cálculo de investigación de la mina tiene por objetivo investigar los procedimientos necesarios para que por determinadas galerías (generalmente talleres) circule un caudal de aire suficiente para hacer posible el trabajo en dichos puntos. Sin embargo, los cálculos de redes de ventilación se limitan a los análisis de redes previamente establecidas por métodos matemáticos que no pueden ser utilizados en pequeños ordenadores. En ese sentido, el presente texto señala las aplicaciónes del nuevo algoritmo matemático aplicable al cálculo de redes por ventilación de minas.

Sep 1, 1975

By A. Banerjee, J. P. Weiler, J. Jekl, J. T. Wood, R. Berkmortel

"The work presented here is part of an ongoing project designed to develop predictive capabilities of the local mechanical properties, and thus, structural behaviour of a thin-walled high-pressure die-cast AM60B magnesium alloy component. This work focuses on developing correlations between process parameters and local microstructure. Numerical simulations of the die filling and solidification behaviour of the AM60B component were used to estimate local process parameters such as solidification rate, temperature gradient, filling velocity, etc. These estimated parameters were used to establish semiempirical correlations with measured VALUES (of the local microstructure measured in regions throughout the component of different solidification conditions. INTRODUCTIONHigh-pressure die-cast magnesium alloys are experiencing increasing use in structural automotive components. A strength-to-weight ratio comparable to steels and its ease of castability allow for these alloys to be utilized in such capacities as instrument panel beams, seat and door frames, and engine cradles, among others (Gjestland and Westengen, 2007). However, the current use of these alloys is limited due to variations in local mechanical properties. These local property variations restrict part designers to assume lower than actual properties, resulting in larger sections, thus diminishing the light-weighting advantages of magnesium alloys. If these local property variations could be predicted, part designers would be able to optimize die-cast magnesium alloy components and fully take advantage of the light-weighting capacity of these materials.The work presented here is part of an ongoing project aimed at developing predictive capabilities of the local mechanical properties, and bulk mechanical performance, from variations in local microstructure, and ultimately from local process parameters in die-cast magnesium alloys. This project, unique in its nature, is based upon the results determined from fifty sequentially cast AM60B magnesium alloy instrument panel beams provided by Meridian Lightweight Technologies (shown in Figure 1)."

Jan 1, 2012