Search Documents

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By J. Stuart Warner

The reaction COSO4(c)?CoO(c) + So3(g)was investigated from 950° to 1170OK by two different methods. The sulfate was decomposed in a previously evacuated space and Pso3 calculated from the measured total pressure on the assumption that Pso2 = 2P02. The sulfate was also decomposed under conditions of controlled oxygen pressure. The difference in the results obtained by these experimental techniques is attributed to the effects of thermal diffusion. The standard free energy change for the reaction is given by ?F° = 66,292 + 17.273T log T — 102.57 T (±300 cal/mole). It was found by DTA and X-ray diffraction studies that CoS04 undergoes a transformation at 617°± 4°C. THE metal sulfates may decompose directly to the oxide or pass through one or more intermediate basic sulfates. Provided the oxidation state of the cation does not change in the course of the reaction, the decompositions may be described in general as follows: One of the major objectives of this work was to determine the validity of Eq. [3] as much of the existing sulfate data has been calculated from decomposition pressures by Eq. [5]. The type of apparatus generally used for these measurements consists of a reaction vessel at high temperature which communicates with a manometer at room temperature. A temperature gradient is thus imposed on the gas phase causing thermal diffusion which brings about a partial separation of the different gaseous species present in an initially uniform mixture. The basic theory and experimental facts associated with this phenomenon are summarized elsewhere1 and it will suffice to state here that the heavier gaseous species diffuses down the temperature gradient. Since thermal diffusion destroys the homogeneity of the gas phase, it is not necessarily true that Pso2 = 2Po2 in any particular volume element of the gas phase even though there are twice as many molecules of SO, as of 0, in the gas phase considered as a whole. Under these conditions, the decomposing sulfate gives off SO, which dissociates to SO, and 0, and all three species are distributed throughout the system by thermal diffusion. However, the sulfate will continue to dissociate until the equilibrium value of PSo3 is established on the hot zone. Thermal diffusion may distribute SO2 and O2 throughout the gas phase in any way so long as Eq. [2b] is satisfied in the hot zone; i.e. Pso2(Po2)1/2=K3pso3. When a steady state is reached, we can characterize Pso2 in that

Jan 1, 1962

By A. C. Losekamp, J. B. Conway

Thermal-expansion data for, tungsten, rhenium, tantalum, .molybdenum, niobium, W-25 pct Re, Ta-10 pct W, ant1 Mo-50 pct Re are presented covering the range from room tempature to 2500°C. In these measureMents, made in a resistively heated tungsten tube furnace operating in a helium atmosphere, data for rod and sheet specimens were found to be identical; in addition, arc-cast and sintered tungsten were found to yield essentially identical results. Optical rneasurenlents of thermal expansion .made in any atmosphere other- than vacuum are subject to a refraction error which can be quite substantial. Specimens tested in helium appear shorter than when tested in racuum and hence a special correction factor must be applied to the helium data in order to obtain accurate results. WHILE it is true that linear thermal-expansion data for many of the refractory metals have been measured to very high temperatures, it is also true that except in a few instances the data from various investigators are not in good agreement. This is particularly evident in the case of tantalum and niobium although some tungsten data have been reported which differ by as much as 40 pct from the data of other investigators. Due to the sensitivity of both tantalum and niobium with respect to impurity absorption during exposure to high temperatures, it is probable that this single factor accounts for the majority of the discrepancies in the thermal-expansion data for these metals. However, this same factor can probably not be employed to explain the existing differences in the tungsten data. In all probability, these are due to errors in the measurement technique, to material composition variations, or to changes which take place in the material during the heating process (e.g., additional densifica-tion resulting from heating a sintered specimen above the original sintering temperature). In view of the discrepancies which exist in the linear expansion data reported for many of the refractory metals, the current study was initiated in an attempt to resolve such differences. Also, no high-temperature linear thermal-expansion data were found to be available for several refractory metals. Providing such data was another objective of the current investigation. MATERIALS In this study test specimens were employed in either rod or sheet form and in several instances both arc-cast and sintered material were employed. Material compositions are presented in Table I. Helium gas was fed to the furnace at a rate of about 0.5 SCFH and no special purification procedures were employed. However, the helium contained less than 50

Jan 1, 1967

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By E. Zucker

In this paper, as in the 1960 CIM paper of the same name, s1gmf1cant new developments in electrical-mechanical mining equipment are briefly described. These include static thyristor-supplied D.C. drives for mine hoists, load-haul-dump systems, process controls with small and medium-size computers, and several other new items of equipment and Concepts. All the new hardware descriptions are given in the context of over-all process integration. This means the actual mechanical linking together of two or more processes and the preliminary step in the development of production-line mining.

Jan 1, 1969

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-substitution with clays and organically bound. Rare earth minerals (REMs) such as monazite exist in coal and have a grain size less than 5 microns. Froth flotation was successful in concentrating REMs existing in a thickener underflow material derived from Fire Clay seam coal which contained around 300 ppm of rare earth elements (REEs). Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2300 ppm REEs. Using a laboratory flotation column, a concentrate containing around 4700 ppm of total REEs was produced equating to an enrichment ratio of 10:1. INTRODUCTION Rare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets, and batteries [1, 2]. REE recovery from alternative sources such as coal and coal by-products has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials. The average REE content of the world coal is around 60-70 ppm [2]. There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia (300-1000 ppm), the Fire Clay coal seam in eastern Kentucky (500 ppm), and the Sydney Basin in Nova Scotia, Canada (72-483 ppm) [3-6]. The occurrence of REEs in coal and coal by-products can be classified into three types, i.e., rare earth minerals such as monazite and xenotime, ion exchangeable REEs in clays, and REEs associated with organic matrix. The particle size of the rare earth (RE) minerals in coal and coal by-products is very small and normally in the micron and/or nanometer scales. The flotation technique, which is based on the surface chemistry difference, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime, and bastnaesite [7-11]. As such, flotation is a promising method for the concentration of REEs from coal and coal by-products. In the current study, rare earth flotation was conducted using the fine coal refuse generated at an operating coal preparation plant treating coal from the Fire Clay seam. REE concentration by flotation required an appropriate amount of grinding and control of the pH value while using typical collectors. Prior to RE concentration, release tests were conducted to evaluate the floatability of the recoverable coal and the REE distribution in the flotation fractions in the fine refuse. Mineralogy of the REE was studied using SEM-EDX."

Jan 1, 2017

By V. V. Trusova, Shiyrav Gandandorzh, K. V. Fedotov, V. A. Domracheva

"In Russia, 1.1 million tons of mercury-containing waste are stored. The amount of mercury in soils and heaps of industrial enterprises is estimated at 3000 tons; in dumps, concentration tailings, sludge dumps of the gold mining industry up to 6000 tons have been accumulated. Mining is one of the main sources of mercury emissions in the natural environment that poses a real threat to the natural environment. At present, the process of amalgamation is prohibited and not applied in gold extraction. The application of amalgam technology in gold mining led to the accumulation of highly toxic products in the form of gold-bearing amalgam and metallic mercury, with a mercury content of dozens and even hundreds of times greater than the maximum permissible concentration for soil (1). Therefore, mercury-containing tailings constitute an ecological hazard to the environment. According to published data, at waste storage sites of industrial enterprises, up to 50 tons of mercury enter soil annually, and up to 3.5 tons pollute the air. At the same time, mercury-containing waste due to the reduction of the country's mineral resources is an additional source of mercury. Therefore, it is necessary to recycle mercury-containing waste. INTRODUCTION Paperobjective: demercurization of technogenic raw materials (amalgamation tails, discharge outlets of tailing dumps) to be recycled. Under natural conditions, the mercury usually migrates in the form of three most common compounds: elementary mercury (Hg); mercuric mercury ion (Hg+2); methylmercuryion (Hg (CH3) +. Chemical compounds Hg (II) are found in natural conditions much more often than Hg (I).The authors propose to conduct demercurization of technogenic raw materials (mercurial tailings) in two stages. At the first stage, the mercury in the form of small balls, the finest particles (drip mercury) can be extracted by applying the gravitational method. We propose a method for centrifugal processing of crushed waste in the apparatus of Itomak company, Novosibirsk, as the basis of the technological process for mercury recycling. The extraction of metallic mercury out of mercury-containing waste into commercial products, according to the technological characteristics of the Itomak apparatus, reaches 86.0% (2, 3). At the second stage, the extraction of mercury out of technogenic raw materials is performed applying a sorption method and using carbon sorbents based on fossil coals. Hard coal of the Kuznetsk Basin has been already used for industrial production of active carbons (carbon sorbents) of the KAD-iodine type, which is one of the prerequisites that determine the choice to use it for the aims of this study."

Jan 1, 2018

By Walter R. Hibbard, Ming-Kao Yen

VARIOUS rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two,1 three,2 five,4 an indefinite number,5 and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, † the necessity for the operation of slip systems capable of producing the required, changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: I. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, - the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only-not translation, inversion, nor others-is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal dose-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1948

By C. S. Barrett, P. Coheur

ANNEALING twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the recrystallization texture,1 and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (111), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3,4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture this is true, for example, with the (113) [211] texture so commonly reported for brass-hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism . MATERIALS AND METHODS The samples investigated were of secondary copper (melted in Belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice has not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip 10 cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a cameral that traversed

Jan 1, 1946

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3&apos;4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3&apos;4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By George H. Found

DURING recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" of a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating mechanisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experimental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,1 damping due to localized inelastic stress relaxation at inhomogeneities within the metal,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.4 How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables have been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About 100 hr, after straining, a stable value is reached of magnitude proportional to the amount of strain.7 In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By Edward Saibel

THE various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure, no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3,4 or on the energy required to form new surface.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agreement between calculation and experiment. It has been pointed out by several observers7 that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so - nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory Of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermo- dynamic theory of the tensile strength of isotropic bodies based on work of Born9 relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melt- ing phenomenon, Fürth obtains an expression for the rupture stress u, in the form [ ] where Q is the melting energy per unit mass, ? is the density, and µ is Poissons’ ratio. Fürth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By B. N. Das, J. B. Darby, P. A. Beck, Y. Shimomura

A POWDER pattern for the (Cr, Mo, Co)R-phase annealed at 1200°C was reported in 1951.1 Through the courtesy of Prof. D. P. Shoemaker of Massachusetts Institute of Technology the authors became aware of inconsistencies of this pattern with that to be expected from the structure of the R-phase, as determined by Komura, Shoemaker, and Shoemaker.&apos; In addition, Professor Shoemaker also noted that the powder pattern reported8 for the (Cr, Mo, Co)D-phase, annealed at 1300°C, agreed fairly well with that to be expected from the newly determined structure of the R-phase. In view of these findings, the previously reported powder patterns of the R-phase and of the D-phase were compared carefully. It was found that most lines in the two patterns (22 lines) were to a fair degree of accuracy related to each other by a single conversion ratio for the corresponding d spacings. The value of the conversion ratio was found to be 1.0058, so that the d spacings of the D-phase pattern previously reported were larger than the correspond- ing d spacings for the reported R-phase pattern by approximately that factor. The intensity relationships between corresponding lines in the two patterns were similar, as judged visually. The following exceptions were noted: Lines Nos. 2, 3, 19, 20, 21, 22, 23, 24 and 25 of the D-phase pattern,:&apos; all designated weak or very weak, were missing in the apparently somewhat fainter R-phase pattern used.&apos; Lines 1, 2, 3, 5, 15 and 34 (all weak or very weak), reported for the R-phase, were missing in the D-phase pattern, Table I. In view of these observations it seemed probable that the two patterns differed from each other mainly by a slight change in lattice parameters (with c/a remaining approximately constant), and that the pattern previously reported for the R-phase contained some weak extraneous lines, most likely to be attributed to impurities. In order to check the foregoing assumption, two specimens of an alloy containing 43 pct by weight of cobalt, 41 pct molybdenum, and 16 pct chromium, which was within the composition range of stability of both the D-phase at 1300°C and of the R-phase at 1200°C, were homogenized at 1200 and 1300°C, respectively, and quenched. X-ray diffraction patterns of the powders of these two specimens, obtained with CrK radiation, were compared carefully with each other and with the D-phase pattern previously

Jan 1, 1959

By R. A. Masumura, C. S. Pande, D. Agassi

"Grain size has a different effects on the critical current density (Jc) of high and low transition temperature (Tc) superconductors. In high Tc superconductors, the critical current density Jc across grain boundaries depends sensitively on the misorientation 8. It was pointed out by Pande that this dependence is directly related to dislocation structure of the grain boundaries i.e., it is due to dislocation cores and stresses. These ideas are developed further in this paper leading to a relation between Jc and 8. The analytical result is compared with the experimental results on bicrystals and used to explain the difference in behavior between high and low Tc superconductors.IntroductionThe grain size distribution and its evolution with time and temperature is important in determining the properties of high and low transition temperature (T c) superconductors. The distribution is a convenient function to characterize the processing of a high Tc material during sintering. For example, it is known that the maximum density of ceramic materials is obtained when the grain growth is reduced but grain boundaries are still mobile. For practical superconductors, the processing parameters are selected to achieve optimum properties: highest possible T c and maximum critical current (Jc). In terms of an average grain size, the requirements for optimum T c and Jc are sometime in conflict. In A15 type superconductors and even in NbTi, larger Jc have been measured in smaller rather than larger grain sized material. Conversely, in a high Tc materials like YBa2Cu307, higher Jc have been found in larger grain sized or single crystal specimens.Extended defects such as grain boundaries in low T c superconductors can be effective pinning agents for magnetic flux lines, thereby increasing the transport critical current density of these materials [1]. On the other hand, the transport critical currents in polycrystals of high Tc superconductors such as YBa2Cu307 is found to be relatively small (much smaller than those in single crystals of the same material) [2]. It is now known that grain boundaries in high Tc polycrystals can in many cases form ""weak links"" reducing the critical current density across them. This phenomenon can be studied more precisely by experiments on bicrystals, where there is only one grain boundary. It is found that the critical current density is quite sensitive to the misorientation angle of the bicrystal [3,4]. Although the original experiments were conducted on YBa2Cu307, other Tc superconductors have been shown to give the same result [5]."

Jan 1, 1994

By T. I. Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook&apos; and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field&apos;s production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company&apos;s Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946