Search Documents

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

Two of the problems long associated with the complete extraction of level pillars in the wide ore bodies of Broken Hill have been: (1) The high cost of maintaining level gangways through areas of slow subsidence to provide adequate trucking roads for the transport of sand filling; and (2) The difficulty and high cost of completely filling depleted areas. This paper deals with the experiments conducted to devise an apparatus for transporting, with the aid of compressed air, sandfill from the underground sand passes to the stopes and describes the sand blower which has been developed. This apparatus has to a large degree overcome the difficulties and removed much of the hazard associated with the rapid extraction of level pillars.Special attention is drawn to the sizing analysis of the sand and to the fact that it is not dry material. It was early found that these factors were determinants in the design and development of the apparatus described.Acknowledgment is made to the General Manager of Broken Hill South Limited for permission to present this paper, to the engineering department for assisting in the design of the apparatus, and to the underground staff for their co-operation in training the operators and in bringing to success this method of stope filling.PREVIOUS FILLING METHODSThe South Mine, with a monthly production of approximately 32,000 tons of lead-sHver-zinc sulphide ore by cut-and-fill mining methods, requires about 11,000 cubic yards of filling per month. With the exception of a small and variable quantity of developmental mullock, all this filling is...

Jan 1, 1941

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By D van der Wal, R Dobbe, K Moeller

"Ore mineralogy and texture are primary variables controlling mill recovery efficiency in flotation plants. However, tracking daily variations of key mineralogical characteristics such as species-by-species liberation is not possible with current on stream analysers and assay lab techniques. In addition, traditional plant mineralogical analysis limited by long data turn-around times from central analysis laboratories typically provides only a time-averaged view of mill performance, e.g. by means of monthly composite feed, con or tailings analysis.This paper presents the results of a development and first field test of an on-site Automated Mineralogy solution (MLA or QEMSCAN) with the specific goal of monitoring recovery variation, ore quality and flotation performance on a mineral species-by-species and day-by-day basis, from up to twelve million direct particle observations per month. The trial was performed at a Pb/Zn-Ag operation in the US from November 2012 to April 2013. The focus of the study was three-fold: to validate the robustness of equipment and operational procedures for daily use by mine site technicians at a remote mine site to develop a methodology to boil down hundred-thousands of Automated Mineralogy particle data from size-by-size con and tailings samples to a couple of numbers meaningful to chief metallurgists to monitor recovery trend changes and correlate these to changes in the feed properties and/or flotation efficiency.The study focused primarily on the Pb/Ag rougher-concentrator circuit. Ten polished blocks of two and three size fractions of con and tailings were prepared by mine site technicians during a daily twelve hour shift. Eight hours of daily measurement time by the instrument revealed an estimate of the dayÆs recovery performance, ore quality and flotation performance for Freibergite (Ag-species) and Galena (Pb-species), within 36 hours from initial sampling. Data quality was assessed by means of calculated versus measured assay reconciliation. Cumulative sum curves of recovery performance, ore quality and flotation performance reveal trend changes with a frequency of 1 to 4 weeks. These were correlated to cumulative sum curves of e.g. locked and slimed particle classes of the mineral species of interest, attempting to identify a possible root cause of recovery performance trend changes. Systematic over-grinding and flotation chemistry issues were the primary causes of below average plant operations during the trial.CITATION:van der Wal, D, Dobbe, R and Moeller, K, 2013. Development of an on-site mineralogy solution for metallurgists, in Proceedings MetPlant 2013, pp 126-132 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By T N. Little

The author contends that geoscience is presently under-utilised in the rock fragmentation by blasting process. Before we can set standards in this area, the following is required: mine geologists need to gain a better understanding of the blasting process and the blasting team needs to obtain a better appreciation of geology. Both groups need to be informed of what can be done to improve blasting outcomes, why it is necessary and how it can be achieved. By working closely together, both the geoscience toolkits and blasting expertise can be applied and focused on priority blast sensitive issues, with potential to improve mine economics and safety. Finally, and ideally, mine geologists need to take a leadership role in raw rock mass data collection and data management, and invited to take an active role in rock mass related behaviour data collection, integration and presentation.This paper attempts to provide insight into all these prerequisites for setting a new standard for collaboration and mutual learning in this strategic opportunity area. The potential for blasting to leverage downstream processes is highlighted. Blasting objectives and blast design principles are introduced along with the required rock mass related inputs. Some hazardous geological materials and environmental conditions are described, along with how they can affect operational complexity.Four case examples are used to illustrate the need for closer liaison between geology and blasting professionals. The first related to grade control blasting, aims to demonstrate how a blasting geology approach can add significant value. Case example two demonstrates how geological models and bench face analysis can assist with fragment control. The third and fourth case examples involve an overview of two case studies where timely geological and geotechnical knowledge input and intervention into blasting activities may have reduced losses due to blast initiated open pit slope collapses.CITATION:Little, T N, 2017. Geoscience input into blasting operations – let’s set a new standard, in Proceedings Tenth International Mining Geology Conference 2017, pp 375–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Mansour Asri, Philippe Somogy, Youssef Daffi, Amor Karim

Very few cases of Cast Blasting use in phosphate mining are reported. However, in open-cast coal mining, Cast Blasting is a common practice. And yet, the geological structure of both types of deposits is similar. Accordingly, advantages for phosphate open-cast mines are manifest, especially as future conditions of phosphate deposits fit quite well with the approach.

Jan 1, 2015

By W. P. Roux

Owing to decreasing high-grade ore reserves, there is a need for better understanding of the jigging process to improve the recovery efficiency of finer, lower grade material. The use of positron emission particle tracking (PEPT) was examined as a technique to study the motion of iron ore particles inside a laboratory batch jig. PEPT is a non-invasive method that can provide three-dimensional kinetic data on a particle in laboratory-scale processing units and has been successfully used to study mills, hydrocyclones, and flotation. Experiments were conducted to determine whether PEPT would be a viable technique to study iron ore jigging and what valuable information could be obtained. The results indicated that detailed information on the stratification rate of a particle could be obtained, with adequate resolution to track the particle?s movement through an individual jig pulse.

Jan 1, 2014

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By J. S. Mason

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Detailed paragenetic studies of the post-tectonic fracture-hosted vein mineralisation have demonstrated a complex paragenesis, reflecting a multi-phase combination of regional metallogenesis and tectonics through time. Previously published work regarding paragenesis and zoning was oversimplified. Two major epochs of mineralisation resulted in the emplacement of the A1 group of assemblages, from which lead, copper and silver were the main metals mined, and the A2 group, whose galena is only moderately argentiferous but which were major sources of lead and zinc. Tectonic and tentative isotopic evidence points to post-orogenic relaxation as the mechanism for development of the A1 assemblages in the early Devonian, whereas the A2 assemblages are believed to reflect Variscan extensional regimes and regional metallogenesis in the early Carboniferous and Permian

Jun 19, 1905

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By Roxana Barrantes Huamán

El presente texto describe la geología económica del depósito aurífero Alpacay ubicado en Arequipa, Perú. El depósito Alpacay es un típico depósito mesotermal, filoniano que es explotado por la Cía Minera Yanaquihua, donde el mineral es procesado en una planta de cianuración, gravimetría y flotación. Costa. Asímismo, se realiza en la Franja Aurífera Nazca-Ocoña que alberga innumerables minas y depósitos en vetas angostas como Arirahua, San Juan de Chorunga, Chalhuane, Las Clavelinas, María Eugenia, entre otros. La alteración es básicamente argílica en la vecindad de las vetas y propilítica hacia el exterior.

Sep 12, 2011

By Lawrence F. Johnsen

In 1989, the Connecticut Department of Transportation authorized the evaluation and design for a reconstructed Route 1 bridge over the Quinnipiac River in the City of New Haven, Connecticut. The project extends from the intersection of Route 1 with East Street, easterly for approximately 3/4 mile to the intersection of Route 1 with Wheeler Street and Stiles Street. The reconstructed roadway will be relatively on-line and widened to provide for four lanes of vehicular traffic and a single-track railway line. The existing bascule bridge and approach spans, which were constructed in 1924, will be replaced by a 270-foot span lift bridge and new approach spans. The lift bridge will have a main lift span weighing approximately 3000 tons, second largest after the Burlington Northern Bridge over the Williamette River in Portland, Oregon. The new bridge will widen the navigation channel to 24 0 feet and provide vertical clearances of 13 feet when closed and 62 feet when open. The project is located in an industrial area. Adjacent properties include retail gasoline sales, auto repair, railroad transport and bulk storage of petroleum. Existing structures include the Yale Boathouse and several retaining walls serving as containment dikes for petroleum storage tanks. The Yale Boathouse, located on the east bank of the river, was constructed in 1909-1910 and is eligible for listing in the National Register of Historic Places.

Jan 1, 1993

By M. Bustillo, S. Ordonez

"Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The Mississippi Valley-type deposits occur in massive, homogeneous dolostones from which diagenesis has obliterated all primary sedimentary structures. The mineralisation forms irregular, lens-shaped stratabound bodies, mostly in the lower part of the dolostones. They are composed exclusively of sphalerite, galena, pyrite, marcasite and barite, with white sparry dolomite a common cementing phase. Mineral zoning can be recognised from pyrite and marcasite in the east to barite in the west. Sphalerite, the most common sulphide, occurs basically as colloform and banded crusts and galena as isolated cubic or skeletal crystals, mainly in the centre of the banded botryoidal sphalerite. The combined observations of the deposits' geology, geochemistry and ore petrology suggest a three-stage genetic model: carbonate sedimentation in a shallow-water environment; dolomitisation, probably after compaction, by fluids of connate origin and lateral evolution; and mineralisation by migrating solutions, perhaps related to oil-field brines, that originated in deep zones of the basin during diagenesis of the basinal mudrocks in the NE"

Apr 1, 1995

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988