Search Documents

By W. L. Phillips

The plastic properties of lithium fluoride and magnesium oxide under compression were investigated in the temperature range 25° to 1000°C. At the higher test temperatures, the critical resolved shear stress and the rate of work-hardening of both materials decreased. At the same time, the number of stress lines decreased and the individual stress lines became wider. The density of dislocations decreased for a given strain the higher the test temperature for lithium fluoride. The decrease in the critical resolved shear stress as a function of temperature could be fitted by the equation 7 = Toe-KT. THE influence of temperature on the stress-strain curves of a variety of metal single crystals has been studied for a wide range of temperature.1"5 In general, it has been found that both the critical resolved shear stress and the rate of work-hardening decrease rapidly with increasing temperature and fall to a value of essentially zero well before the melting point is reached. AS the test temperature is increased, the density of slip lines has been found to decrease, while the width of the individual lines increases. Recently, Gallagher,' Graf et al.,7 and Pate1 and Alexander8 have found that single crystals of germanium and silicon, which have a covalent bond, can be plastically deformed at elevated temperatures. In compressing germanium it has been found that the strain-hardening coefficient decreased very rapidly as the temperature was increased. The coefficient did not tend to zero, however, as the melting point was approached. The plastic properties of ionic crystals at elevated temperatures have not been extensively investigated. In the only work previously reported Tamman and salge9 and Theile10 have shown that the yield point of sodium chloride single crystals tested in tension and compression decreased slowly with increasing temperature, falling to zero at the melting point. As the temperature was increased, they found a substantial increase in the amount of plastic deformation that could be sustained before fracture; and at temperatures above 400°C in tension tests there was an obvious necking which produced local extensions of up to 3000 pct. The purpose of the present work is to extend the knowledge of high-temperature deformation to the ionic crystals, lithium fluoride and magnesium oxide. The following were investigated: 1) The gross shape of the stress-strain curve at several temperatures. 2) The change in the critical resolved shear stress as a function of temperature. 3) The appearance of slip bands and the density of dislocations as a function of strain and temperature. EXPERIMENTAL TECHNIQUES The lithium fluoride and magnesium oxide used in this investigation were purchased from the Harshaw

Jan 1, 1961

By Dever C. Ashmead

Anthracite was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and the method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they are mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracitc. Mining Methods and Their Relation to Preparation In the beginning of the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a, knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal. Real mining of anthracite began about 1808 when Judge Jesse Fell, of Wilkes-Barre, discovered that the "common stone coal of the valley" could be burned in an open grate. For some years thereafter mining was conducted near the surface. The working p1aces were driven narrow; only the best of the coal was selected and the remainder was left in the ground. Only the lumps could be used, as no market existed for other sizes. As time passed, however, it became necessary either to go farther into the ground or to widen the working places. When these places were widened, falls of roof were apt to occur, making it necessary

Jan 1, 1922

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By Charles C. Hawes

DETERMINATION OF SILICA OXIDE iron ores usually are found in intimate association with silica and phosphorus compounds. Their quantitative separation and purification sometimes present difficult problems to the chemist. Silicic acids may represent various degrees of dehydration. They are exeedingly weak, but combine with metallic oxides and form some of the most stable oxides in nature, the silicates. When iron ores are treated with hydrochloric acid, they yield practically all their iron. However, apart from rare exceptions, varying amounts of insoluble residues of silica, alumina, lime, magnesia and compounds of phosphorus, sulphur, titanium, chromium and others will be left. If the oxides of silicon, aluminum and titanium are present in small quantities, the insoluble residue is generally very small, but the presence of these oxides is more usual in larger quantities. Therefore, only a special treatment can break the bond between these elements. Ore Residues Acids remove the soluble constituent of the ore, leaving the insoluble residue, which chemically is rock or gangue and must be treated accordingly. Alkali carbonates are used frequently to break up the residue, but other fluxes have also been recommended, such as a number of lead and boron salts. The introduction 0f these salts, which offers certain advantages, requires, however, their removal before the other constituents can be analyzed, and this elimination is sometimes difficult. Usually in quantitative analysis silicates are dissociated by fusing them in a platinum crucible with sodium carbonate, thereby forming sodium silicate, Na2SiO3, sodium aluminate, Na2Al204, sodium titanate, Na2TiO3, and carbonates of other elements. All the carbonates are soluble in hydrochloric acid, but also some silicic acid is formed that must be rendered insoluble. To this end the solution is evaporated several times, as the first evaporation still leaves as much as 5 per cent of the silica soluble. Even after a number of evaporations, minute quantities of silica may be found with the iron and alumina present. Perchloric Acid as an Agent for Dehydrating Silicic Acid Perchloric acid, HC104, (60 per cent), has been used for years as a solvent, but few chemists have used it to dehydrate silica. It is derived from anhydrous perchloric C1207, which is most unstable and dangerous. Perchloric acid is a strong oxidizing agent, which boils at 203°C. It is more effective in rendering silica insoluble than any other known agent, and most rapid in action. After perchloric acid is added to a mixture containing silicic acid, the resultant solution is

Jan 1, 1945

By Foster Bain

THE outstanding characteristic of the last hundred years has been the world-wide rise in the standard of living. Man's dominion over nature is increasing with an accelerating pace and more and more the forces and materials of this world are being made to serve man's necessities and his convenience. We demand both quantities and varieties of goods that were beyond the dreams, to say nothing of the reach, of our fore-fathers, and our possession of them has become so much a matter of course that they excite no remark. Literally, thousands of young folks have required an explanation of a recent popular song, "Thanks for the Buggy Ride," for the reason that their own experience does not extend back into the pre-flivver age. This transition from the use of vehicles made mainly of wood and drawn by animal power, to metal made cars propelled by mineral fuels is all but complete and the memory even of older conditions is already fading. This is symbolic of what is happening all around us. In a recent book, Dr. Frank J. Goodenough, president of Johns Hopkins University, referred to Chinese civilization as a ?vegetable" civilization meaning thereby that the Chinese depend mainly upon the plant world for food, clothing and other necessities and luxuries. Our own people did the same hardly more than a hundred years ago. In 1820, this country produced and used only 5 lb. of pig iron per capita, but a quick and enormous change was wrought in the hundred, years that followed, and in 1920 the amount was 119 times as much, or 597 lb. It has since increased even beyond this and touched a peak of 809 lb. in 1923. In that year our output was more than twice that of 1903 and nine times that of 1883. This increase in production

Jan 10, 1926

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By Fazel G. Jahromi, Ahmad Ghahreman

"Several studies were performed on the atmospheric leaching of copper sulfide minerals in the presence of activated carbon and a new catalyst, AF 5. AF 5 is a carbon based catalyst with similar properties to those of activated carbon however much better mechanical properties. The activated carbon surface chemistry has been investigated in various studies; however the connection of the surface chemistry of activated carbon and AF 5 with the sulfide minerals during the atmospheric leaching process is not well-understood yet. Based on the surface analysis, AF 5 showed higher surface area than activated carbon (AC). Adsorption and oxidation of copper, arsenic and iron ions in the presence of different activated carbon were investigated. Adsorption properties of both catalysts were similar and 18-24% of iron, 12-18% of copper and 10% of arsenic adsorbed on the catalysts surface form 5 g/L Fe(III) and Cu(II) and 2 g/L As(III) at 80°C. In oxidation experiments, both catalysts reduced Fe(III) and Cu(II) ions and re-oxidized the reduced species in the presence of oxygen and oxidized As(III) ions. The addition of oxidizing ions can enhance the oxidation process kinetics and increase the catalytic capability of carbon.INTRODUCTION Hydrometallurgical processes of copper sulfide concentrates are under development and various different methods have been proposed to increase the atmospheric leaching rate of copper sulfide minerals. These methods include using different media, reagents, and catalysts. Among different methods, leaching of the copper sulfide minerals in the chloride media has some advantages over sulfate media. Smaller scale of operation, increased leaching rates, and lower sulfate formation are some of the benefits of the chloride leaching media over other similar media. Moreover, using ferric and cupric ions as oxidants and utilizing activated carbon as a catalyst has been proven to enhance the leaching rate of copper sulfide minerals effectively. Activated carbon (AC) and AF 5 (micro porous carbon based catalyst) are two of the most efficient and practical catalysts in copper sulfide leaching processes. AC can enhance the copper recovery of enargite in chloride media from 69% to 92% after 96 hours of leaching under the similar conditions (Jahromi & Ghahreman, 2016). It has been shown that AC at acidic pH can generate hydrogen peroxide in the presence of oxygen which can leach copper minerals (Ahmumada et al., 2002)."

Jan 1, 2017

By David C. Grant

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. Mter mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability.

Jan 1, 1982

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

By B. K. Gorain

Barrick' s Buzwagi copper-gold deposit in Tanzania comprises oxide, saprock and sulphide mineralized zones averaging approximately 0.058oz/t gold, 0.13% total copper and 0.03% cyanide-soluble copper. A comparative evaluation of the project based on two potential flowsheet alternatives is presented. The first flowsheet included a gravityconcentration and carbon-in-leach (CIL) plant. The second flowsheet was based on a Gravity-Flotation-CIL plant, which proved to be more economically robust. Selective flotation of copper minerals to produce a saleable copper concentrate proved to be challenging. Detailed characterization of the Buzwagi deposit was carried out through understanding of ore mineralogy, mineral liberation, floatability and selectivity, reagent chemistry and regrinding issues. With this insight, a flotation concentrate of greater than 25% Cu was achieved, recovering a significant amount of copper minerals and tellurides. The overall economics of the project improved significantly with the addition of flotation. Leach tests on gravity and flotation tailings showed an overall increase in gold recovery of approximately 6% for a Gravity-Flotation-CIL plant compared to that for a Gravity-CIL plant.

Jan 1, 2007

By E. S. Leaver

THE amount of gold that occurs in a ton of milling ore from most of the large-scale copper mines is so small that unusual care and special attention are necessary to recover it. In some cases the gold is not considered important enough to warrant daily assays of the various products. Considering the large tonnage of copper ores that are now concentrated by flotation, as computed in a recent review, the gross gold content is surprisingly large, probably amounting to over 10 million dollars per year in the United States. The indications are that in many of the copper-milling operations with gold content under $1 per ton, only 50 per cent. of the gold is recovered in the flotation concentrates. Lime is generally used as a depressant for pyrite in the flotation circuit. The authors have shown that high lime or a solution high in calcium ions is also a depressant for gold. Their experiments on several well-known ores show that by careful regulation of the alkalinity of the mill solutions, a higher flotation recovery of the gold can be obtained, together with equally good copper recovery in a good grade of copper concentrates. In cyanidation for the recovery of gold, the best accepted practice demands that the mill solutions be tested and regulated by simple chemical reactions at definite periods during treatment or with each change in the treatment. It is similarly important for the recovery of gold that the solution in the flotation circuit be analyzed for calcium ions at regular periods and at each step in the flotation practice. The lime should be added when and where needed and not in excessive amounts at the head of the mill.

Jan 1, 1931

By R. A. L. Black

Rock mechanics is a very new science. It has been accepted as a recognized discipline for some two decades, but it is only within the last five to ten years that it has been common to include the teaching of rock mechanics as a separate subject in undergraduate curricula at universities. Thus, few senior mining engineers practicing in industry, either men in charge of production or those engaged in mine planning and design, are familiar with the subject. That this unfamiliarity has continued so long is also due in part to the fact that the results of rock mechanics investigations have been published in a large number of different periodicals covering subjects ranging from experimental stress analysis to obscure branches of applied earth sciences. The first really useful textbook ' in the English language was published only in 1965, in Canada. It made available to students and to practicing engineers, for the first time in concise form, the essential body of accepted knowledge about rock mechanics and developed the theories on which it is based in a simple, clear and logical manner. Another factor which has resulted in rock mechanics science being slow to be accepted by the mining industry is that research work has often appeared to be esoteric and unpractical. Senior engineers have been reluctant to spend money on the application of new knowledge when the process of application seemed uncertain and ill-defined, and where the cost of field investigations (which is necessarily high) appeared to offer no certainty of economic reward. This is a reasonable attitude on the part of mining engineers; they are responsible to skeptical boards of directors whose chief concern is, very properly, the net return on capital invested. The application of rock mechanics science has not in the past,

Jan 1, 1968

By Roger Holmberg, Kenneth Mäki

This paper describe; open pit studies where blasting damage introduced in the remaining rock has been investigated. Results from two open pit mines are described and discussed. Parallel performed laboratory experiments, where simulated blasting damage has been introduced into samples before shear strength testing took place, are also reviewed. These studies are tied together in order to throw some light upon how the blasting damage influences the slope stability. A mathematical model is also described which will make it possible to optimize the blast design for a specified damage zone in the rock mass.

Jan 1, 1983

By William L. Lennemann

Chemistry of uranium with respect to its hydrometallurgical recovery from carnotite ores was investigated and well defined during the radium boom period between 1900 and 1920. Since that time, methods used to extract uranium from its ores have remained basically either acid leaching or sodium carbonate leaching. Until about 1950, the only practical methods known for achieving a better than 75 pct U2O3 concentrate from the leach liquors involved fundamental chemical techniques for either purifying a solution prior to the uranium precipitation, or refining a crude uranium concentrate that was produced by neutralizing a pregnant mill liquor.

Jun 1, 1956

The volumes of Transactions, which are published annually, contain the list of officers, rules, etc., the Proceedings, and the papers revised for final publication. (In this revision, after the preliminary publication, authors are permitted to use the largest liberty; and the changes and additions made in papers are sometimes important. It should be borne in mind by those who study or quote a paper in the preliminary edition, that they may not have in that form the ultimate and deliberate expression of the author's views. It should be added, however, that in the majority of cases there are no important changes.) These volumes are for sale as follows, in paper covers:

Jan 1, 1917

Discussion * of the paper of H. M. Chance, presented at the butte meeting, august, 1913, and printed in bulletin No. 79, July, 1913, pp. 1315 to 1341. George H. Ashley,+ Washington, d. C.:-Mr. Chance's long practical experience in reporting on coal lands admirably fits him for a discussion of the value of such lands. On behalf of the government geologists, I wish to express my appreciation of Mr. Chance's friendly, constructive criticism of the government method of valuing coal land in the first part of his paper and, at the same time, to reply to some queries he makes. All admit that coal has no " intrinsic "-monetary value, in the sense that a pound of coal of certain chemical and physical characters is worth " intrinsically " so many cents or fractions of a cent. The term has, however, been found very useful as including those natural factors of coal value, among which are its position and location in the earth, that affect its sale price in contrast with the other cost elements involved in the labor and capital necessary in mining, preparing, transporting, and selling the coal (extrinsic factors). Mr. Chance, while recognizing the " dual origin of value," does not offer any better terms. The survey agrees with Mr. Chance in his definition of coal conservation, that it means the fuller utilization of the heat contents of the coal, and the more complete recovery of the coal from the ground. Coal land withdrawals have not been made to keep such lands off the market, but to prevent their acquisition as non-coal lands before they could be classified so as to be disposed of under the proper law. Nor has the pricing of the more valuable coal lands above the minimum been to raise money for the reclamation fund, to which the money goes, but primarily to discourage the alienation, for holding or speculation, of coal lands not intended or needed for development, and, secondarily, to secure to the people the ?unearned increment," which they are certain in any case to be charged.

Jan 11, 1913

By F. J. Hogan

In early 1982 Atlantic Cement Company, a wholly-owned subsidiary of Newmont Mining Corp. will come on line with a new water granulating grinding facility at Sparrows Point, Maryland to produce 800, 000 tons a year of separately ground granulated blast-furnace slag. The process and product will be unique to the United States. This paper will review some initial investigations undertaken to evaluate the cementitious properties of granulated slag. The effect of slag fineness on strength development is discussed and data is presented showing a relationship between glass content and hydraulicity and grindability of slag.

Jan 1, 1982

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. 1). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By Robert P. Larkin

The necessity for mineral extraction and its impact on man and the natural environment is a subject of increasing concern to Americans. Rising living standards and new demands for energy require increased mineral extraction, whereas the "new environmentalism" and concern over social well-being warn of the dangers to both the environment and the social system. This dilemma can only be solved by a complete understanding and analysis of all the factors relevant to human welfare which include environmental considerations, economic implications, and the social and psychological dimensions. A decision-making framework is therefore necessary which will encompass all relevant views of the problem.

Jan 1, 1975

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977