Search Documents

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

By Cyril Stanley Smith

ON the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1958, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Cavallo3,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold-working restored it. He encountered some samples of brass that could not be rendered magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condition, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitters in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant,9 Honda and Shimizu, 10,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1941

By R. P. Carreker

THE experiments described in this report were conducted as a part of a general program designed to document the deformation behavior of pure metals over a wide range of temperature. Material The silver used in this investigation was obtained from the Handy and Harmon Co. as 99.97+ pct pure. It is from the same length of wire as that designated H-H silver by Hoffman and Turnbull in their investigation of self-diffusion in silver.' The silver was drawn at room temperature from 0.060-in. diam to 0.020-in. diam wire without intermediate annealing. Seven-inch lengths of cold-drawn wire were annealed in groups of ten by placing them in individual quartz tubes spaced circumferentially about and near the vertical furnace axis. Dry nitrogen was passed through the furnace to lower the partial pressure of oxygen. The three annealing temperatures used were 700°, 800°, and 900°C, producing grain sizes of 0.017, 0.040, and 0.250 mm diam after 30 min at temperature. Testing Procedure The details of the testing procedure have been described in the reporting of results of a similar investigation of Copper. Annealed specimens of 5-in. gage length were gripped between grooved plates. Tests were performed using an Instron tensile-test-

Jan 1, 1958

By J. P. Conway

The yielding-rock-bolt concept, as developed in South Africa, consists of a smooth-bore die or collar fitted to a standard rock bolt. Laboratory testing at the Bureau of Mines Spokane Mining Research Center under slow and fast strain rates showed that extrusion loads can be controlled by varying the configuration of the die bore and that theoretical analysis (using basically Sachs' theory of wire drawing) predicts extrusion loads of the different die-bore configurations. A derived equation, based on this research, can be used for designed die-thread combinations for any desired extrusion load. Dynamic loading resulted in slightly higher loads (15 percent) than static loading. The strain hardening effect, which increases yield and ultimate strength, was partly offset by adiabatic heating of the threads, which decreases strength.

Jan 1, 1975

By Howard J. Smith

For several years this Institute has recorded in its Transactions the various discoveries of potash‡ in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons of salts with an equivalent of 144,342 tons of pure potash. Mine and Plant Improvement During 1935, the American Potash & Chemical Co., at Searles Lake, Calif., began to reap the benefits of its previously enlarged plant facilities, which increased its productive capacity to 180,000 tons of muriate annually. The United States Potash Co., at Carlsbad, N. Mex., improved its operations by installing trolley locomotives and other haulage facilities and is maintaining its development headings two years in advance of operations, with projected plans for orderly mining for years to come. The hoisting shaft at its mine is now equipped to hoist at the rate of 1,000,000 tons annually, and the refinery to produce 150,000 tons of muriate containing less than one per cent of impurities. The Potash Co. of America, at Carlsbad, N. Mex., completed the conversion of its plant from a prospecting to an operating basis late in 1935. The coarse-crushing plant, with a capacity of 150 tons an hour, formerly on the surface, was installed underground, with ore pockets

Jan 1, 1938

BHP BillitonÆs Yandi channel iron deposit has a large resource of approximately 1.3 billion tonnes. This is a bulk mining operation with a high degree of selectivity not being practical. In contrast the deposit geology is a complex interrelationship of primary channel facies, secondary enrichment of iron and a secondary redistribution of the major contaminants. These variations in geology and alteration can occur over ranges of hundreds of metres down to knife edge contacts. In addition, differences in primary facies and mobility during alteration often result in the iron and contaminants having different patterns of enrichment and depletion. Despite the scale of these operations, if the geological domaining is not optimal, significant errors in the resource estimate of grades and tonnage will occur. Getting the geology right has become a common clichT among mining professionals. However, in many situations, obtaining optimal geological domains for resource modelling is best achieved when there is input from geology, statistics and geostatistics. In this paper, moving window statistics are utilised to see through locally high variability to identify trends that assist in locating difficult to identify geological boundaries. After the creation of geological domains, univariate and multivariate statistics and principal component analysis assist in validating and characterising geological domains. Finally, variography and domain contact analysis are used to analyse the nature of the boundaries between geological domains. At the Yandi channel iron deposit, the inter-relationship between geological and geostatistical analysis has resulted in significant improvements to geological domaining and the treatment of domain boundaries during estimation of iron and contaminates.

Jan 1, 2005

By A. Kishimoto, Yoshida Honmachi, T. Uda, Y. Taninouchi

Recycling of e-scrap is often performed by utilizing a pyrometallurgical Cu smelting process. Several valuable metals, including precious metals, can be efficiently recovered through the Cu smelting process. However, recovery of Sn is quite difficult because it is distributed in slag during the smelting process. Sn is used as solder and plating in electronic devices, and its recycling will be more important in the future. In light of this background, a pretreatment process that can extract Sn directly and selectively from e-scrap was developed in this study. The proposed Sn extraction process involves alkaline leaching using iodate ions, IO 3, as an oxidizing agent. We conducted leaching experiments for Sn, Sn-Ag-Cu alloy solder, and Cu, and the effective dissolution of Sn was confirmed. In principle, the electrodeposition of Sn from the leach solution and regeneration of IO3 are possible by a subsequent electrolysis process. The results obtained in this study suggest that the proposed leaching process can be an effective and useful pretreatment for Cu-smelting-based e-scrap recycling. INTRODUCTION Electronic scrap (e-scrap), including waste printed circuit boards (PCBs), is one of the fastest growing waste treatment streams in the global urban environment. E-scrap contains numerous valuable metallic elements, including Cu, Sn, and precious metals, in rich quantity. Furthermore, some metals and other materials contained in e- scrap are hazardous to human health and the environment when they are not properly managed. The recycling of e- scrap is therefore a major concern in terms of resource supply and waste treatment, and it has been performed by many companies using a variety of methods.

Jan 1, 2019

By Woolsey McA. Johnson

In metallurgical circles it is known widely, but somewhat vaguely, that the ease of reduction of metallic oxides depends largely on the way they hare been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction temperature of zinc oxides variously prepared and of several kinds.' In said paper it was shown that the temperature at which zinc oxide evolves zinc according to the equa-tion ZnO + C = Zn + CO depends upon the nature of the two reacting bodies. The determina-tions had a range of accuracy of from 2° to 6°C., whereas differences were found to amount to an extreme of 90' C. So the differences are real ones and must have a definite cause. The equation of boiling water, (H2O)4 D 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. In general, all equations reacting in the liquid or the gaseous phase have well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the tempera ture conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules. In other words, there are two forces to be overcome: a certain

Jan 1, 1914

By Hans W. Brodbeck

The main problem in tunneling without the use of explosives lies in the development of tools capable of continuous mechanical destruction of rock, resulting in a fragmentation which lends itself to a smooth, uninterrupted transportation of the broken rock away from the tunnel face. While all moles of U.S. design mainly achieve this by crushing the rock by means of "disk cutters" or "roller bits," a boring system based on the principle of cutting the rock came into being in Europe, whereby the rock is worked in a manner very similar to the milling of metals. For tunneling purposes, this principle was first developed by the late Austrian engineer Wohlmeyer. Between late 1962 and the spring of 1965, the first experimental machine was tested in a German coal mine, working in coal and shale over a distance of some 3000 ft, divided over two runs separated by a period of time to allow for equipment modifications. In 1964, a collaboration was started between Wohlmeyer and the Habegger engineering firm of Thun in Switzerland. The normal Habegger range of equipment consists of aerial ropeways, ski lifts, and certain tool machines, to which in later years have been added monorail passenger-transport systems. One of these was installed as the main mode of transport at the 1967 World Fair in Montreal. After taking over the Wohlmeyer patents, Habegger further developed the original cutting principle, aiming at more robust machines in order to be able to tackle harder rock. A first machine was built and tested at a site near Thun in sandstone averaging 17,000 psi compressive strength and limestone of 25,000 psi. In May 1966 this machine was delivered to Japan for the boring of a pilot tunnel for the Honshu-Hokkaido railway connection under the sea. A second machine, incorporating many improvements based on experience gained with this first mole, was built during 1966 and tested in the same limestone as mentioned previously (25,000 psi), before being installed to bore the head race tunnel of the Julia hydroelectric power scheme near St. Moritz, Switzerland, in the early summer of 1967 (Fig. 1 ) .

Jan 1, 1970

By Howard J. Smith

For several years this Institute has recorded in its Transactions the various discoveries of potash‡ in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons of salts with an equivalent of 144,342 tons of pure potash. Mine and Plant Improvement During 1935, the American Potash & Chemical Co., at Searles Lake, Calif., began to reap the benefits of its previously enlarged plant facilities, which increased its productive capacity to 180,000 tons of muriate annually. The United States Potash Co., at Carlsbad, N. Mex., improved its operations by installing trolley locomotives and other haulage facilities and is maintaining its development headings two years in advance of operations, with projected plans for orderly mining for years to come. The hoisting shaft at its mine is now equipped to hoist at the rate of 1,000,000 tons annually, and the refinery to produce 150,000 tons of muriate containing less than one per cent of impurities. The Potash Co. of America, at Carlsbad, N. Mex., completed the conversion of its plant from a prospecting to an operating basis late in 1935. The coarse-crushing plant, with a capacity of 150 tons an hour, formerly on the surface, was installed underground, with ore pockets

Jan 1, 1938

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in .he discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in he smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently n the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of he joined pieces (base metal). The filler metal, older or braze, is always of lower melting point than the base metal. Consequently with these) recesses there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Joining operations carried out at temperatures above 500°C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used.

Jan 1, 1975

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By H. F. Easter

(San Francisco Meeting, September, 1915) THE lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly oil a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been clue partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lead or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted heady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. This matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is clone by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 8, 1915

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

By Fuller P. G, Miller D. R

Hydraulic fill using surface sand deposits or cycloned tailings has been used in underground mining for at least fifty years. Current technology requires a permeable fill and high cement additions for strong fill. Shortages in quantities of acceptable fill with finely ground ore may require rockfill or aggregate to be introduced as a supplement and these usually incur additional distribution costs. Alternative approaches to the problem are now being developed whereby the pulp density of the fill is raised so that it is delivered either as a dense slurry or as a paste. These regimes of fill behaviour are defined together with the plant and pumping techniques required to prepare and deliver the materials. Test techniques to define the different regimes of behaviour are identified and the variation in material properties for fills with varying pulp densities are outlined. The results indicate that high pulp density fills are stronger and have less permeability restrictions than conventional fills and that aggregate can be carried with the pulp. Thus the disadvantage of finer materials can be turned into an economic advantage. Criteria are developed for defining the type of operation suited to this Technology.

Jan 1, 1986

It is very apparent that the hydrogeotogicat characteristics of mineral deposits in China be dominated by meteoric factors, terrain factors and the kind of karstic aquifers as a main source threatening the mining.The hydrogeotogicat characteristics of mineral deposits in dry areas are very different from that in non-dry areas.The rote of precipitation is very important to mine dewatering.The difference of water recharge condition of a mineral deposit located upper (or under) Local erosion basis is existing. There are more than two million square kilometers of carbonate in China.Many water-bearing deposits are distributed in it.According to the karst shapes the surrounding karstic aquifers of mines can be divided into three kinds including solution fissure aquifer,karstic cave aquifer and underground stream (karst stream) aquifer. Underlier invasion is a main feature of karst water-bearing coal mine and upper tier incoming is a main feature of skarn copper and ferro mine.Swatlor pillar and collapse is a special feature of karstic water-impregnated mine.

Jan 1, 1988

By T. V. Philip, R. E. Lenhart

C. G. Dunn(General Electric Research Laboratory)— It is well recognized that understanding of the formation of the cube-on-edge texture in annealed commercial cold-rolled Si-Fe strip is important industrially as well as scientifically. I would like to make a few remarks on this subject, discuss some points in the present paper, and list two remaining problems that appear to be particularly outstanding. Attention should be drawn to the paper by P. K. Koh,23 which also considers the kinetics of secondary recrystallization in 3 pet Si-Fe, produced commercially by the Allegheny Ludlum Steel Corp. Koh covered a much larger temperature range than do either the present authors or P. N. Richards, whose work is mentioned in a footnote. Koh found an induction period (of short duration) even for isothermal anneals at 1260oC (2300°F). Koh and Dunn24 also found a change in texture during the 1260oC anneal for the same material. On the other hand, the material in coil D, according to Philip and Lenhart, underwent no sec-condary recrystallization, only continuous grain growth. The grade classifications of the four coils studied would suggest, however, that all four materials had developed the cube-on-edge or (110) [001] texture, but to varying degrees. Since no data on this are given and since watt loss depends

Jan 1, 1962

By W. David Leyshon

This paper compares the general characteristics of Florida phosphate rock for the manufacture of fertilizers and phosphoric acid. The subjects covered are relative reactivity for superphosphate manufacture and various properties of the rock for use in phosphoric acid production, including gypsum filterability, sulfuric acid consumption, foaming, relative cor-rosiveness, chemical composition, and others. Comprison will include rocks of North Africa, the western U.S., and other locations. This paper reviews some of the important properties of phosphate rock, giving particular attention to a comparison of Florida phosphate with some of the major phosphates produced in the world. It also discusses some of the techniques available for evaluatine Phosphate. rock for phosphoric. acid and fertilizer use. The use of Florida rock outside the U.S. has been increasing steadily, evidence in itself of certain desirable properties of this rock. Table I is a list of the major producers and exporters of phosphate rock as of 1965. Florida, meaning in this case Central Florida, was the largest producer of phosphate rock and the largest exporter of rock. Of a total world production estimated at 60 million tons, about 50 million tons were produced during 1965 by the areas listed in Table I. One major producing area omitted from Table I and from subsequent evaluations in this paper comprises Nauru, Ocean, and Christmas Islands, whose output totaled about three million tons in 1965. This phosphate is marketed entirely by the British Phosphate Commissioners, primarily in Australia and New Zealand, and does not get into the world market elsewhere to a significant degree at the present time. South Africa, Egypt, Israel, and North Vietnam also produce lesser quantities of rock for the international market, and these materials are also excluded from this review. The phosphate industry is now seeing the introduction of several new areas that will be significant factors in the rock market in the future. The North Carolina and North Florida areas each have capacity at present or in the near future for producing about three million tons per year. The Djebel Onk mine in Algeria has a potential of about 800,000 tons per year. In addition, announcements have been made of significant development of deposits in Peru and in the Spanish Sahara, and sizable expansions are planned in several of the existing areas that are now of minor importance. Competition for the rock market appears to be increasing so that more attention will probably be paid to evaluating phosphates available from different areas. It is not possible here to go into all the properties of even a few of the materials listed in Table I. However, it is practical to discuss some comparative properties important for making phosphoric acid and fertilizers, and to touch on the techniques used for the evaluation of various phosphate rocks. Table II gives typical analyses of the major phosphate rocks available in the world as of 1965. There is, of course, an inherent danger in labeling any analysis as typical, but it appears that variations between two samples of rock within one given area are generally less than between two samples from different areas. The analyses listed were compiled from several years of data so they may not be representative of the present output of any particular area. The range of grades represented by these analyses goes from 66 BPL for Gafsa rock to 85 BPL for Kola

Jan 1, 1968