Search Documents

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By Don Reining

The sand and gravel industry in Southern California has made a sizeable contribution to the construction development of the 15 County area in this part of the State. Facing this mineral extraction industry, in the next decade, is a problem of meeting the market demand. The question is, "how can sand, gravel and rock operations be made compatible with goals for sound and attractive community development?" Three basic principal characteristics of the land needed for this-mining industry are: 1. The land must have workable sand, gravel or stone deposits. 2. The land must be properly located for transportation purposes close to the market in order to sell the aggregate at a minimum cost. 3. The land must be zoned so that it will be permissible to mine.

Jan 1, 1967

By Patricio Campos

Durante los diez últimos años, la perforación hidráulica ha desplazado al sistema neumático en aplicaciones mineras y obras civiles. En ese sentido, el presente texto describe las ventajas e inconvenientes de este sistema hidráulico como alternativa futura en el campo de la perforación. La aplicación de esta tecnología aumentó la productividad en la perforación de roca y disminuyó a un costo menor de operación que la de perforadora neumática. De forma que se la considerará como proceso obligatorio en breve plazo, al tiempo que mejora el ambiente de trabajo del personal.

May 1, 1982

By R. V. Ramani, R. Bhaskar

Control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. Understanding the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been at-tempted. In this paper, first, a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It in¬corporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1987

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By Andrews Allen

THE large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc. have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired hoisting tonnage can be secured and, since only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining.

Jan 2, 1921

By A. M. Talbot

THERE is still considerable controversy as to the exact nature of the mechanism of the age-hardening process, in spite of the many experi-ments already performed. For this reason, a considerable number of typical systems should be examined in detail and their results correlated. Furthermore, the methods of studying the changes that take place during the progress of this phenomenon should be carefully scrutinized and the different methods applied to the same samples, preferably at the same time. The experiments described in this paper are presented to supply information on one age-hardening system and to show how the various methods of investigation compare in their indication of what has hap-pened. In brief, the progress of aging in magnesium alloys containing about 10 per cent by weight of aluminum at different temperatures was followed by measurements of hardness, electrical resistivity, dilation and lattice parameter, and by microscopic observation.

Jan 1, 1936

By Eugene T. Sheridan

This report presents data on individual plants of the fuel-briquet and packaged-fuel industries that were circularized by the Bureau of Mines, United States Department of the Interior, in its annual survey for 1958. Only plants that processed fuels of mineral origin were included; specifically, plants that manufactured briquets from charcoal were excluded. Fuel briquets and packaged fuel are manufactured by mixing fine-sized fuels with binders and compressing into small individual shapes. Both are used mainly for residential heating in the United States, but they differ considerably in appearance and physical characteristics. Briquets usually are produced as small, pillow-shaped forms, 2 to 4 inches in length, weighing from 2 to 4 ounces. Pack-aged fuel consists of 3-to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. Briquets are made with a water-insoluble binder and are designed for rough handling and outdoor storage, whereas packaged fuel generally is made with a water-soluble binder and must be stored indoors to prevent deterioration. Briquet plants are relatively large and usually are at mines or in dock areas where large quantities of fine-sized fuels accumulate. Packaged-fuel plants are smaller and are used chiefly by retail dealers to convert locally available coal and coke fines into a product that can be burned efficiently in residential beating equipment.

Jan 1, 1959

By Herbert H. Fields

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (1), and pipeline--quality gas was introduced into a commercial pipe-line. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed,

Jan 1, 1975

By E. J. Duggan

In the course of the grinding experiments conducted at Climax over the past twenty years one interesting phenomenon was discovered. This was that balls made of certain types of steel grind more ore than some others. The most significant variation was found in the results secured with a hard alloyed forged bail compared with the forged carbon ball supplied by most ball manufacturers These findings were confirmed in many repeated controlled tests. The value of these tests depends on the methods used, the facilities available and the care with which the investigations were conducted. These are described in the following. This testing has largely been done in eight 91 x 81 low discharge ball mills in closed circuit with 7811 duplex screw classifiers. The mills run at 20 RPM on a feed approximately minus 3/8 inch. The ore is ground through 28 - 35 mesh in one stage. Each mill and auxiliary classifier is in a separate, parallel grinding and flotation section The, ore to each: section is the same in every particular and is fed to each mill bin from a common conveyor tripper. The ore from the bin to the ball mill is weighed on a conveyor scale. The power input to each mill motor is determined with a watt hour meter which measures the power to the mill motor only. Both the scales and meters are checked periodically by standard methods and have been found to give consistent readings. Automatic samplers are employed on each section to obtain accurate measurement of the size reduction. A size analysis of the classifier overflow is made each shift and a composite size analysis is obtained from a weighted average of the various shift analyses. The mills are driven by 450 horsepower synchronous motors so that there is no speed variation and shell liner age is kept as nearly the same as possible in mills under test. The same set of operators is assigned to a mill under test as to the control mill. In all other particulars such as ball load, mill density, liner design, etc., the mills are operated in precisely the same manner. This is an ideal arrangement for plant testing. From observations of ball mill performance over the past twenty years, it is the opinion of the operating staff that variations of as little as one to two percent in mill capacities may be determined if sufficient operating hours are devoted, to a test. Relations between mill capacities, fineness of grinds and power consumptions have been established with a high degree of accuracy. In Table I are given the figures for one test. These show that while the grind with the hard ball was slightly coarser, the tons ground per hour was 5.4 percent greater with the soft ball, and 6.1 percent greater on the basis of minus 100 mesh produced. The power consumed per ton with the hard ball was 4.4 percent greater on a tons per hour basis. The soft ball was inferior in wearing qualities and steel consumption per ton of ore was 24 percent greater with it. In this test the mills were charged with the two different balls for a period of three months to allow the ball loads to come to equilibrium. In Table II are given the specifications of the two balls. The difference in grinding rates may be accounted for by the nature of the ball surfaces. The surfaces of the soft balls after being worn a while are rougher to the touch. Enlarged photographs of the worn-in surfaces of hard and soft balls are shown in Figure I. These show the presence of scratches or skid marks on the hard ball surface which indicates less nipping effect. The Climax ore pulp has a pH of 6.0 and is in a dispersed state. The viscosity is low compared with most ores especially those that are conditioned with lime. This would lower the tendency of the pulp to adhere to the balls with a lower grinding efficiency as a result. It was also thought that the relative rates of wear from surface to center might affect the make-up of an equilibrium ball charge. This probably has little effect on capacity as shown by the size analyses of the two ball charges in Table III. This hypothesis was subsequently investigated by the use of rationed charges. The rationed charge did not overcome the advantage in

Jan 1, 1958

By Mark Malamphy

MOST igneous rocks, and particularly those of the basic type, con-tain relatively high percentages of magnetite and other iron oxides, which give them moderately high magnetic susceptibilities and make them responsible for an important percentage of the magnetic anom-alies observed during the course of geophysical surveys by the mag-netic method. The irregular form and high susceptibility of the igneous rocks make them readily polarizable and the position and strength of the magnetic poles formed are not always explicable by theoretical calculations of anomalies due to certain assumed forms in the normal magnetic field of the area under study. During the last four years our field work has permitted us to make detailed observations of anomalies due to igneous rocks in all the states of south Brazil. The form and position of the igneous rock at some places were fairly accurately known, which made it possible to calculate theoretical anomalies and compare them with the observed data. Some of the data we obtained have been published and additional cases are now awaiting publication. In this paper, we will present a few specific cases where the geology is moderately well known and which we believe to be of considerable value as representing typical magnetic anomalies in the south magnetic hemisphere, where the inclination of the magnetic field is very low. Although the vertical intensity is negative in the Southern Hemis-phere, we have adopted the convention of plotting increase in intensity (negative) as a positive anomaly; i.e., above the x axis. This conven-tion facilitates comparison with anomalies in the north.

Jan 1, 1936

By R. Barany

The heats of formation of gehlenite and talc were determined by hydro-fluoric acid solution calorimetry. The results are reported in terms of the constituent oxides (?H298.15 = -31.1 ± 0.5 kcal/mole for gehlenite and ?H298.15 = -44.9 ± 0.3 kcal/mole for talc) and in terms of the constituent elements (?H298.15 = -952.8 ± 0.7 kcal/mole for gehlenite and ?H298.15 -1,415.5 ± 1.4 kcal/mole for talc).

Jan 1, 1963

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,' an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By W. B. McCarter

Broadly speaking, the year 1934, one of the most active in the history of the Coast, has been both disappointing and revealing. Of the 18 new oil-producing areas, only two have shown the qualities of a first class oil field. Many of the new areas are discouraging for the horizons exploited, because of close association of gas and salt water, and the absence of any appreciable oil zone. In spite of amply fulfilling the expectations of drilling and geophysical development, the year has fallen far short of the results that normally should be expected from such a campaign. In 1934, the Cockfield zone has been disappointing because its exploration down the dip from the Conroe and Tom Ball fields revealed only such distillate fields as Splendora, Eureka, and the great gas-sand thickness at Katy. The zone proved good at Raccoon Bend. Newer Oligocene and Frio fields in Texas, with the exception of Hastings, were also disappointing, as Van Vleck arid Old Ocean attest. The discovery at Dickinson is not startling. The development of Hastings, Tom Ball, Dickinson and the deep zone at Raccoon Bend will be slow. A new strip of prospective territory of minor importance lying inland from the Conroe trend was opened by the Kittrell discovery. During the year 206 unproductive wildcats were drilled on the Texas Coast, compared with 207 during 1933 and 141 during 1932. During 1934, there were 835 oil and gas wells and 229 dry holes drilled in proved fields, in contrast with 1100 in 1933 and 512 in 1932. The past year's production was actually 60,868,260 bbl., or 2,020,764 bbl. less than in 1933. The present annual rate of Texas Gulf Coast production is about 61 million barrels per year. The daily Texas Coast production decreased 5537 bbl., or 3.2 per cent, during the year. The total daily production at the end of the year was 173,598 bbl. Eighteen wildcats opened up new oil and gas pools during 1934, so that there are now 78 active pools and 3753 producing oil wells. The production of the average well is 45 bbl. per day. The price of crude oil was almost uniform in 1934,

Jan 1, 1935

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953

By P. H. Griffin

The manufacture of iron in the Province of Quebec forms one of the most interesting subjects in the development of this great industry in America. It began soon after the first steps taken in the New England colonies, where iron was first practically made in America. In both cases the ores smelted were bog-ores. In Qaebec the first work was done in and about, the town of Three Rivers, and many interesting facts in connection with the development of this industry may be found in the paper read at the Halifax meeting, September, 1885, by Mr. James Herbert Bartlett, of Montreal,* which traces the industry from its inception, about 1730, down to 1883, at which time the St. Maurice forge is declared to be the oldest active furnace on the American continent. A few years later the Canada Iron Furnace Company, Ltd., became interested in the enterprise, the extent of which has been greatly enlarged beyond all former limits. In fact, the manufacture of this particular class of iron has never been attempted on the scale now practiced by this company. This work has been carried on for the purpose of supplying a grade of iron hitherto procurable only at heavy cost for Canadian consumption from the United States, and for English consumption from Sweden. The manufacture of iron in the Province of Quebec was based entirely on bog-ores during the period referred to; and as the supply of iron made elsewhere from cheaper ores became more abundant, the local manufacture, handicapped by want of shipping facilities, lack of capital, and other natural causes, was gradually discontinued. It was always admitted that for certain purposes the iron made in the Province possessed special value; but the demand for articles requiring such special virtue was limited, and cheaper grades were gradually substituted for general uses. Some years ago we were led to test, in our car-wheel shops at

Jan 1, 1893

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By Ruilin Lang

This paper presents an application of 3-D plots and non-linear regressions to define a sitespecific form of the charge weight scaled distance. The PPV (PPA) of single hole blasts is normally considered as a function of two independent variables - the charge weight and the distance. It is of great importance to obtain the relationship of the function accurately for a concerned site in terms of blast vibration analysis and modeling. However, in pre-computer time it was difficult to plot 3-D graphs. Consequently, a charge weight scaled distance was used to plot the PPV (or PPA) against the scaled distance as 2-D graphs. Blast vibration investigators use several forms of the charge weight scaled distances to plot data. We can exemplify them with the cube root of charge weight scaled distance, the square root of charge weight scaled distance, and other forms (Hossaini and Sen, 2004). Each of these scaled distances assumes relative contributions of the charge weight and the distance to the vibration attenuation. For example, the charge weight is assumed to have a less contribution to vibration in the cube root scaled distance than it is assumed in the square-root scaled distance. In reality, for different sites the relative contribution of the charge weight and the distance may be different and site-specific. This may explain that in some cases, the blast vibration data plots using these charge weight scaled distances are scattered. This could be largely due to the fact that the definition of the form of the charge weight scaled distance is not adequate for the particular site condition.

Jan 1, 2006

By J. Bartrum

Semi-autogenous, (SAG), milling operations can realize substantial Increases in mill throughput by removing and crushing critical size, slow grinding, material from the SAG mill. Full-scale plant testwork showed that modifying the Kidston SAG/ball circuit to a semi-autogenous-ball milling-crushing (SABC) circuit would increase plant throughput by 25 to 30%. The methods used to determine the value of the SABC circuit and the design of the circuit are discussed.

Jan 1, 1988