Search Documents

By Phillip J. Maddex

Transportation is a major part of yours in the industrial minerals industry. Whereas federal income taxes merely take 50 per cent of your firms profits, transportation cost may take 50 per cent of the gross realization - selling price plus transportation - on your product, f. o. b. customers plant.

Jan 1, 1969

By Franklyn W. Oatman

In order that the conditions which obtain in an oil well may be readily understood, a brief description of a typical California well and a number of the phenomena accompanying same will be given. That the necessity for the exclusion of water be realized, the effects of water intrusion, a description of methods of prevention, .and a discussion of causes of failure will be presented, followed by a summary and recommendations. Fig. 1 shows a section of a typical well which illustrates the relation of oil sands to overlying strata. It indicates a deep water sand separated from the oil sand by shale, and the proper place for the final shutting off of water. In this well a comparatively thick stratum of compact shale protected the oil from overlying water so that the operation of landing the water string was a simple matter. In some wells the protecting stratum may be only from 3 to 5 ft. thick and very careful operation is necessary in order to land the water string of casing properly and not puncture through to the oil sand. The cases just cited are common, but occasionally, after excluding overlying water, productive oil sands are drilled through in the expectation of finding more productive underlying sand, and a water-bearing stratum is tapped. In this case the problem is the reverse of the normal; water must be prevented from ascending rather than descending. A discussion of well-drilling methods is not within the scope of this paper, except such operations as pertain to shutting off of water. A brief outline of the several conditions which may accompany drilling follows. Some or all may be present in any particular case. The direct relation of these to prevention of intrusion will be discussed in detail further on. In drilling, the hole becomes more or less irregular in shape, and rough, and as the casing follows the bit into the well it does not fit snugly against the walls. As a result, water may descend between the casing and walls of the well. If a circulation pump is not used during drilling, the hole is simply punched through and the pulverized material removed from the well by means of a bailer. If circulation is maintained there is a continual flow of water down inside the casing and up around the outside between the pipe and the walls of hole. This keeps an open space around the pipe.

Jan 1, 1915

By Fidel Torres Inga

El presente texto describe la aplicación de las pruebas con sistemas de iniciación electrónica en la Compañía Minera Suyamarca – unidad Pallancata del grupo Hochschild. Los exámenes se desarrollaron entre diciembre del 2010 y enero del 2011. Los parámetros técnicos evaluados en las pruebas son: el avance efectivo de la voladura, sobrequiere y medias cañas y el costo de extracción de material minado, perforación y voladura.

Apr 1, 2012

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

1. What Is a Rock Burst? . . . . 569 Jack Spalding . . 569 A. F. Robertson . 569 W. R. Crane . 569 G. S. Rice......569 P. J. Shenon........... 569 L. C. Graton........... 569 2. What Are the Causes of Rock Bursts? 573 Jack Spalding..........573 A. B. Yates and P. J. Shenon 574, 578, 592, 596 A. F. Robertson . . . . . 575, 595 W. R. Crane. ... 579 G. S. Rice.........582 Oscar Weiss .........582 P. B. Bucky..........582 P. H. Bird.....588, 592, 593, 595 M. K. Hubbert.........593 G. Wheeler.......... .593 B. F. Tillson........593, 595 T. T. Read............594 3. How Can Rock Bursts Be Prevented?. 597 Jack Spalding..........597 A. B. Yates and P. J. Shenon ... 598 A. F. Robertson.......599 W. R. Crane....... .602 G. S. Rice............602 Page 4. How Can Rock Bursts Be Predicted?. 602 Jack Spalding.........602 A. F. Robertson.......602, 603 A. B. Yates and P. J. Shenon ... 602 W. R. Crane......602 G. S. Rice......602 B. F. Tillson...........603 5. How Can Rock Bursts Be Controlled? 603 Jack Spalding..........603 A. F. Robertson.......603 W. R. Crane...........604 A. B. Yates and P. J. Shenon 604 Oscar Weiss........605 G. S. Rice......- 604, 609 R.D.Hoffman..609, 610 R. D. Hall..........609 R. H. Cromwell . . 609 P. J. Shenon...........609 P. B. Bucky......609, 611 B. F. Tillson.........609, 611 A. B. Yates...610, 611 P. H. Bird.......610 6. General Discussion........ 611 Jack Spalding.......... 611 R. D. Parker....... . 616 C. Baring Horwood........ 618 P. B. Bucky........... 619 Foreword This symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge, which, if successfully met and overcome,

Jan 1, 1946

By Euler M. De Souza

"This paper presents a study developed to assess the potential use of salt tailings as backfill to control surface subsidence and as a mine bulkhead used to isolate areas of potential brine inflows. A series of index tests, centrifuge model tests and quasi-static creep consolidation tests were performed to evaluate the creep and consolidation properties of salt backfl1l and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. The centrifuge models were specifically designed to study the mechanical behaviour of salt backfill under the influence of brine inflow and long-term creep. Test results indicated that salt tailings could be applied underground as a bulkhead to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. It is hoped that this study will assist mine planners to develop contingency plans to control brine inflow occurrences. IntroductionThe use of salt tailings as backfill is a technique that would assist in the control of potential brine inflows and surface subsidence, and would have a very positive impact on the long term adverse environmental effects associated with surface salt tailings disposal. A centrifuge testing program was designed to evaluate the behaviour of salt tailings as backfill; the effectiveness of salt backfill as a bulkhead used to isolate areas of potential brine inflow and the potential use of salt backfill to control surface subsidence. The testing program was also used to evaluate the creep-consolidation properties of salt backfill and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. This paper presents the results of the experimental centrifuge testing program and a comparison of results with models tested under I g using an electrohydraulic servo-controlled loading frame (MTS) and a creep consolidation cell. Applicability of the results to practical underground soft rock mining is also discussed.The centrifuge model tests indicated that salt tailings could be applied underground as bulkheads to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. Because the applied stresses (1.2 MPa) and fill consolidation were relatively low, the centrifuge simulated bulkhead did not retain all of the inflow brine. At typical field stresses it is expected that the fill would be able to seal off panels with brine inflows. Further testing at higher stresses are suggested to determine the consolidation and stress levels at which the fill would completely retain any potential brine inflow head and positively act as mine bulkhead."

Jan 1, 1994

By Komosa T, Muir D. M

Mixtures of ammonia and cyanide at low concentrations leach gold selectively from copper-gold ores. The effects of various reagent compositions on three different ore types containing between 0.3 - 1.5 per cent Cu are reported. It is shown that the results and optimum compositions vary according to the ore, which is attributed in part to the mineralogy and adsorption of solution species on the mineral surfaces. The solution chemistry of the Cu-NH3-CN system indicates that Cu(CN)a - and Cu(CN)3 species are involved in the leaching mechanism. Rotating disc studies on pure gold and copper are reported which show that the Cu(CN)32- species leach gold at about half the rate of CN but leach copper at the same rate. The presence of ammonia retards the leaching rate further. Mixtures of Cu(CN)a3- and NH3 effectively leach gold from Telfer tailing without leaching copper. The role of ammonia appears to be to control the precipitation of copper rather than the kinetics of leaching.

Jan 1, 1991

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By Paul T. Allsman

This paper gives the cost and describes the mining of 55 tons of nickel-bearing rock by hand methods from a prospect in southern Nevada, June 15, 1937, by the Mining Division of the Bureau of Mines. The geology, mineralogy, and problems related to future development also are discussed briefly. The main object was to obtain a 55-ton sample within the limited period during which funds were available; little time was available to make a first-hand detailed study of the possibility of commercial ore deposits being found. The sample was desired by the Metallurgical Division of the Bureau for experimental purposes at the Electro-Metallurgical Station at Boulder City, Nev. The term "ore" is used loosely in the following discussion to designate dike material containing nickel and copper, without consideration of its commercial value. ACKNOLEDGMENTS Material concerning the geology and mineralogy of the prospect and district as obtained from Geological Survey publications by Bancroft3/and Longwell4/.

Jan 1, 1938

By R. W. Guill

"The Apex Mine is currently scheduled to be brought back into production by Hecla in the first quarter of1990. Its projected productivity rate will be exceptionally high for a small underhand cut and fill mine.The ore mined at the Apex Mine occurs within a pipe-like structure as a series of iron oxides containing both gallium and germanium, plus significant amounts of silver, zinc, lead, and copper.Ground conditions in and around the ore zone have dictated that unique approaches be utilized. To date, these have included a prototype 0.5 cu. yd diesel LHD, and the use of fibrous shotcrete in 4ft by 7ft headings, and the first pneumatically-placed cemented backfill in North America. Above all else, it is the combination of new technologies with a small and dedicated workforce which has allowed for the successful development of this ore body.IntroductionThe Apex Mine is an example of the typical small underground project. It has high grade, but low tonnage and is deposited in poor ground. In such cases, conventional planning and thinking generally results in an uneconomical evaluation and negative production decision. Fortunately, some unconventional thinking was allowed to take place during the planning and evolution of the Apex Mine development. The result now serves as an example of how such unconventional thinking can lead to the type of innovations described below.The job necessitated the development and use of new equipment and materials to execute a highly flexible underhand cut and fill mine design/pneumatic backfill concept, that must be constantly modified as different than assumed conditions become evident in and around the ore zone."

Jan 1, 1990

By R. F. Hehemann, Darrell W. Smith

The kinetics of alloying- in W-5 rot pct Re powder compacts were investigated at temperature about the upper limit for the formation of the x phase, such that a single intermediate phase was involved in the process. The rates and directions of motion of the a-o and o-b interface were assessed as functions of tinze at the sintering teri7peraticve by quantitative izetallog-ralhic techtziques. The iiotion 01 these interjuces could be specified approxitnate1.y by u Parabolic )-ate law and deviations from this ,rate law were attribuled to a complex interaction between surface dif'fusion and volume diffusion during the initial stages of sintering. WHEN binary or more complex alloys are produced by sintering compacted blends of elemental powders, a complication is encountered which does not arise in the sintering of pure metals. In addition to concern for grain size and densification, the rate of inter diffusion of the component elements must be considered. The general problem of alloying during sintering has been treated by numerous investigators.'-7 These investigations have been concerned only with systems that form continuous series of solid solutions and a concentric-sphere diffusion model4 provides a useful description of homogenization in these stems.' Some controversy remains, however, over the contribution of surface and grain boundary diffusion to the homogenization process. Heckel% ePorts that homogenization can be described by volume diffusion at all temperatures, whereas other invetiators'' recognize the importance of surface and grain boundary diffusion, particularly at lower temperatures. Analysis of the homogenization process in partially miscible systems is complicated by the motion of the interfaces separating the individual phases. A simple analytical solution does not exist for such finite systems with spherical symmetry. It was the purpose of this work to examine the kinetics of the formation and dissolution of an intermediate phase in a binary system through an assessment of the motion of the interfaces separating this phase from the terminal solid solutions. PROCEDURE The W-Re system is an example of a partially miscible binary system and was selected for study because of its current importance in refractory-metal technology. The equilibrium phase diagram, Fig. 1, shows that the o phase will be formed by interdiffu-sion between tungsten and rhenium. At temperatures between approximately 2125" and 282O°C, the o phase will appear as the only intermediate phase in the diffusion system. In this work, a mixture of elemental powders containing 5 pct Re was employed. In such a mixture, the rhenium particles will be distributed randomly in a tungsten matrix. During sintering, a o-phase layer will form at the W-Re interface. The development and subsequent disappearance of the o phase are controlled by the relative rates and directions of motion of the 0-0 and a-p interfaces. The motion of these interfaces can be inferred from quantitative metallographic measurements of the average radii of the o shells surrounding rhenium particles. Elemental tungsten and rhenium powders of commercial purity were employed in these investigations. The rhenium powder was spheroidized from +200 mesh agglomerates by plasma-arc spraying and was then classified to yield a powder composed of essentially

Jan 1, 1967

By Howard S. Bryant

FROM the viewpoint of the oil producer, the oil refiner, the oil marketer, and the investor, in oil securities, a brief picture of the crude oil supply and demand in the present critical season of the year will be timely and interesting. Although crude oil production has been in a comparatively poor statistical position this year, increased sales and sustained refinery and crude oil prices have allowed increased profits for many oil companies. The large amount of crude oil going into storage during the present period of peak consumption, just previous to the major yearly fall decline in consumption, has caused oil producers to make plans to leave the oil in the ground for the present in several of the areas of large flush production. The present moment is looked on as the turning point in the current year.

Jan 1, 1929

By L. Lamothe, C. H. The

"Pilot precipitator tests were conducted at Noranda's Horne Smelter in late 1978 to evaluate methods of improving converter dust collection efficiency. A bout 35 Nms/min. of converter off-gas were isokineticatly diverted from the converter flue to the pilot precipitator leased from Flakt (Canada) Ltd., consisting of three fields, one transformer-rectifier set per field and 77-m2 total collecting plate area. The effects of gas volume flow rate and conditioning the gas with sulphur trioxide and/or additional moisture were tested. II was found that gas flow rate and moisture level had the most pronounced effect on collection efficiency. Based on a techno-economic assessment of different options for improving converter Courell efficiency, waffle hoods and water sprays were installed on the converters to reduce air infiltration and increase the moisture level in the gas.BackgroundThe Horne Smelter of Noranda Inc. is situated in northwestern Quebec and, since the closure o f the min e in 1976, has been operating as a custom smelter. The concentrates treated at the smelter come from various mines with mixed sulphide ores , many o f them containing significant amounts of lead and zinc which makes dust collection in electrostatic precipitators mo re difficult than normal.As part of a continuing program on reducing smelter dust emissions, the No . 6 Cottrell was installed in 1972 up stream of Nos. 2 and 4 Cottrells (in parallel) in a n attempt to improve dust collection by increasing the over- all precipitator capacity ( Fig. I). However, it has never per formed a t its designed efficiency o f 94%. The average efficiency established in various test s was in the range of 60 – 65%."

Jan 1, 1985

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.'-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

By C. P. Naudé

Mechel, a large, integrated steel, stainless steel, and ferroalloy producer in Russia is committed to upgrading its facilities to world class pyrometallurgical process and environmental practice. Yuzhural Nickel currently uses shaft furnaces to produce a matte containing iron, nickel and traces of cobalt. This rather old technology is thermally inefficient and is characterized by high operating costs. Mechel has investigated suitable equipment and processes to upgrade the plant, and awarded a contract for the construction of a 12 MW DC smelter, located near the town of Orsk, to Bateman Engineering Projects in June 2008. The selection of DC furnace technology for laterite smelting can be considered as a strategic highlight for the pyrometallurgical treatment of low-grade lateritic ores, and could be the first industrial-scale implementation of this technology. This project has been designed to achieve multiple goals including the demonstration of the process and associated equipment technology at commercial scale, to confirm the scale-up design parameters of the forthcoming 2 x90 MW, twin electrode DC furnaces, and to prove the environmental emission superiority of closed furnaces. It also provides a valuable operator training platform. This paper deals with the process design, key technology building blocks and design features which have been incorporated to produce a pyrometallurgical vessel capable of (i) resisting slag superheat and chemical aggressiveness, (ii) process fine material without pre-agglomeration, (iii) achieve high nickel recoveries and(iv) being tolerant to the variations in chemical composition of laterite ore. The approach to increasing campaign lives between partial and complete rebuilds, through the use of composite furnace module (CFM) technology originally developed and patented by the University of Melbourne, is also followed in more detail. Unfortunately, results from hot commissioning and lessons learned from initial operation are not available because the project completion has been delayed due to the worldwide downturn in demand for commodities. Keywords DC furnace, ferronickel laterite smelting, corrosive slag, coppercooler technology.

Jan 1, 2010

By P. Yu, L. X. Liu

"A mechanistic model for tumbling mills was developed during PhD studies at the JKMRC. The concept was presented at the IMPC of 2014, followed by progress in a sub-process of the model presented at the IMPC of 2016. Additionally, a number of papers on the sub-models and breakage function have been published. This paper provides a consolidated summary of the outcomes and status of the model. The overall model structure is presented along with the sub-models such as appearance functions, breakage rate functions, energy distribution, transport, and multicomponent grinding interaction model. The strengths and capabilities of the model structure as achieved to date are presented. The gaps in knowledge and sub-processes are also presented, providing a guide to the areas that require further research and development. It is proposed that the approach developed in this paper provides a structure that can accommodate future mechanistic, dynamic mill model evolution that can incorporate the latest research outcomes and provide a platform to test modelling improvements. This can assist in substantially improving the predictive mill modelling capability in the industry, the importance of which should not be underestimated for this workhorse of mineral processing.INTRODUCTION Grinding is almost the largest single energy-consuming process in the mineral processing industry, which was estimated that about 0.2% of global, and 1.3% of Australia’s electricity is consumed by comminution of gold and copper ores (Ballantyne and Powell, 2014). Although there are some relatively new grinding mills, such as stirred mills, vibrating mills and HPGRs (High-Pressure Grinding Rolls), etc., tumbling mills, as the traditional grinding facilities, are more extensively used."

Jan 1, 2018

By R. A. Campbell, R. R. Rogers

"AbstractThe experiments described show that crude bismuth metal containing up to 5 per •cent lead, 0.14 per cent silver, 0.015 per cent copper, 0.02 per cent iron, .and small amounts of antimony, nickel, and tin may be refined to a bismuth content of 99.98 per cent by distillation followed by chlorination. It also is shown that bismuth trichloride of high ,purity may be produced by passing chlorine over hot •crude bismuth metal and allowing the resulting vapours to •condense in a cooler .part of the system.IntroductionBISMUTH is used in the production of alloys and pharmaceuticals. During 1952, the New York price for the refined metal was $2.25 per pound in ton lots.Some months-ago a Canadian producer requested the Mines Branch to investigate methods of refining the bismuth which they had been producing. Their crude product had been selling for $1.50 to $1.70 per pound and it was desired to increase its purity to at least 99.98 per cent so that it could be sold for $2.25 per pound."

Jan 1, 1955

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By D. B Kibler

The Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Alber-tus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. Early Mining The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to I-yd. capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas power- I house near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939 approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore 1 they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for I the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today i only three companies are operating. These

Jan 1, 1942

By D. B. Kibler

The Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Alber-tus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. Early Mining The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to I-yd. capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas power- I house near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939 approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore 1 they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for I the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today i only three companies are operating. These

Jan 1, 1942