Search Documents

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By James R. Brown

Mount Isa Mine should be regarded as a large mining complex rather than one mine. This arises from the geography, variety and extent of the orebodies, the mining methods, and the use of 14 shafts for ventilation distribution. A brief resume is presented here since comprehensive descriptions of lead-zinc mining methods {11}, copper mining methods {2 }{3}, geology 241, stope fill {5} and ventilation techniques {6}{7}, have all been published in the last five years. Mining extends over a north-south strike length of 2.5 miles (4 Ian) with a maximum width across dip approaching 3 200 ft (1 Ian). Current mining is to a depth of 3 150 ft (960 m) with the ore hoisting shafts extending 660 ft (200 m) deeper. The composite longitudinal section, Figure 1, shows a representational disposition of the copper and lead-zinc-silver orebodies in the central shaft complex where the main service and hoisting shafts are located. To the south the X41 man and materials shaft provides access to the copper area. The mine layout is typical of high tonnage track- less mines, utilising a large diesel fleet, raise- borers and some large diameter hole stope drilling. Mining methods include sublevel open stoping, slot and massfire, and a trial vertical crater retreat in the copper ore, and sublevel caving, sublevel open stopes with and without rib pillar recovery, and mechanised cut and fill in the numerous lead orebodies. All ore reports to one of the three crushing systems located below 19 level in the central shaft complex. Copper ore is hauled exclusively along the 19 level computer assisted Rockflo haulage system, and lead-zinc-silver ores report via central orepasses from Granby haulages on 13 level and 15 level. Tonnages hoisted during the 1977178 financial year were 5.0 million for copper at 3.2%. and 2.3 million for lead-zinc-silver at 7.8%. 6.3% and 7.06 oz/ton (216 g/tonne) respectively.

Jan 1, 1980

Edward S. Simpson, Perth, Western Australia (communication to the Secretary): In 1896 the East Coolgardie gold-field was divided into three fields, viz. : Area, square miles. Officia1 Centers. (1) East Coolgardie,. . 634 Kalgoorlie. (2) Broad Arrow,. , 588 Kurawa. (3) Northeast Coolgardie,. 22,960 Kanowna. The whole of the area embraced by the eastern gold-fields is covered with late Tertiary sands and gravel, with occasional beds of clay shales. These mostly overlay granite which occasionally shows through in small round hills. At Coolgardie, Kalgoorlie and other mining centers, belts of diorite, serpentine and highly metamorphosed sedimentary rocks appear on the surface. The rainfall at Kalgoorlie in 1897 was 4.75 inches. That the climate has not always been so arid is evidenced by the recent discovery at Coolgardie (only twenty-five miles away) in the late Tertiary formations of a thick bed of brown coal, containing numerous fossil fern-leaves. As assayer and mineralogist to the Government of Western Australia I have had occasion to examine a large amount of the Kalgoorlie ores, both in Perth and at the mines at Boulder itself. The only tellurides I have been able to determine are

Jan 1, 1899

By T. Imaizumi

Covering the whole scope of the MMIJ activities, i.e. geology and exploration, mining, mineral processing, and metallurgy, the technical innovations and improvements since 1972 were reviewed. Special references were made to the MMIJ Research Committees which were subsidized by the Japan Mining Promotive Foundation, in connection with those activities.

Jan 1, 1976

By C. S. Matthews, M. J. F. Rosenbaum

The purpose of thir work wax to lcarn it~lzut infori~lation could he obtained from various typs of pilot water floods and to attempt to find the optunum pilot patter11, for a revervoir which had previously been depleted by a solution gas drive. The study was made in the laboratory with mathemetical methods a dynamic analog and a potentiotnetric analog. Results werp tested against the field llistorics of a nrrnlber of pilot water floods. At a reasonable valrre of currzulative injection, the total production rate for the one-injector five-spot should reach about 6.5 per cent of injection rate, and for a four-injector five-spot, about 9 per cent. Accurate estimates of ultimate recovery cannot be made on the basis of such snzall prorluction rates. However, with a pilot composed of nine ir1jector.s and 16 producers the production rate is approximately 50 pcr cent of injection rate at a reasonable value of camulative injection. Sonle inforn~ation for extended performance predictions might he obtained from such a large pilot. These conclusions were drawn on the basis of results obtained for unit mobility ratio, and a sturly using tlre potentiometric analog was made of the effect of other mobility ratios to determine the range of applicability of these predictions. For the four-injector, five-spot pilot with the ratio of production to injection rate (before water breakthrough) is about twice that for with it is about two-thirds; and with M0= 10, it is about one-third For high mobility ratios, it was found that the production rate increased considerably as water-cut increased. These result can be used to modify, qualitatively, the inter.pretntions based on curves for the unit rnobilit\. ratio CaSeS. It was found that the maximum ratio of production rate to injection rate obseriled in field pilot floods was of rhe scime order as that prerdicted by these methods. The time required to reach thisr maximum did not generally agree with the time predicted for a homogeti~orir reservoir. The differcrlce between predicted and observed time of response gives an indication of the permeability profile and of the condition of the producin,g wells. Pilot water floods of the pattern type are generally carried out in reservoirs which have been depleted by solution gas drive and are at low pressure. Under these conditions, oil and water can be considered incompressible. It is assumed that, as the water is injected, an oil bank forms ahead of it and that there is a distinct interface between the water zone (or bank) and the oil zone (or bank) and between the oil zone and the region ahead of the oil zone. It is further assumed that only gas is mobile in the unflooded (gas) region, only oil is mobile in the oil bank and only water is mobile in the water bank. The saturations and the mobilities associated with each zone are assumed uniform. We idealize our reservoir to be homogeneous, horizontal and of constant thickness. Effects of gravity within the producing layer are assumed negligible. If the actual time-dcpendent flow problem is approximated by a acries of steady-state problems. the potential and stream function in the oil bank and water hank satisfy Laplace&apos;s equation in two dimensions. We can therefore use a poteiitiometric analog of this system. Potentiometric models have yielded uscful results in this laboratory&apos; and clsewhere in the study of a variety of secondary recovery problems. For the case where M = I, we generally prefer to use theoretical mcthods as well as a simpler dynamic analog. Except where otherwise noted, the ratio, side of five-spot/wellbore radius. is taken to be 3,600. a figure which corrcsponds to a normal-size wellbore in a 10-acre well spacing. THEORETICAL EVALUATION OF VARIOUS PILOT PATTERNS, Mw0 = 1 <&apos;he theoretical models which we used to examine the performance of various pilots are shown in Fig. 1. Image theory was used to determine the ratio of production rate to injection rate as a function of the volumc of the flood. The ratio of production rate to injection rate was chosen because this is an easily measurable quantity which is characteristic of a pilot

By R. M. Treco

THE purpose of this work has been to investigate recrystallization characteristics of zirconium after cold working and annealing. In order to do this, hafnium-contain ing crystal bars of Foote Mineral Co. iodide zirconium were selected for high purity. maximum diameter (about ½ in.), brightness of surface, and absence of core wire. A typical lot analysis is shown in Table I. In order to obtain uniformity of starting material, all bars were cold-swaged to 0.310 in. diam, annealed for 2 hr at 1000°C, and furnace cooled.

Jan 1, 1957

By T. Reed Scollon

Before we can attempt to answer the question of what can be expected from coal research, let us examine why research is done in other fields and what others expect for the money they spend on research and development. Up to 1900 almost all organized research was carried out at universities. Most of the support came from the university, and by present standards the amount of research was extremely small. The motivation for university research was basically discovery of new phenomena, with the objective of advancing knowledge. Side by, side with this organized effort was that of individual inventors who were primarily responsible for applying this new-found knowledge to useful purposes. During this period inventors were rarely supported by anyone, and experimentation was carried out either in their spare time or at the expense of earning a living. Men like Edison, I believe, were the first to demonstrate on a large scale that one could systematically apply newly discovered scientific principles to inventions that would serve useful purposes and would return a profit to those engaged in the effort. The tremendous expansion in research therefore began with the realization and demonstration that the scientific discovered could be applied in such a way as to return a&apos; handsome profit to those who invested in it. The motivation of many of the research personnel however, remained the satisfaction associated with new discoveries, The money to support their efforts came from those interested in a return on their investments. Since the First World War and a rapidly accelerating rate since the Second World War another important motive for supporting research has appeared--the needs associated with national defense; this type of research has been supported almost exclusively by the Government.

Jan 1, 1959

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By 13409, B. Arjang

"Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxial strain cells were performed at several mine sites to provide stress data for stability evaluations and mine design. Pre-mining stress determinations carried out at depths between 60 m to 1890 m resulted in the following average stress gradients:Maximum horizontal stress, s Hmax = 8.18 + 0.0422 MPa/m depthMinimum horizontal stress, s Hmin = 3.64 + 0.0276 MPa/m depthAverage horizontal stress, s Ha = 5.91 + 0.0349 MPa/m depthVertical stress, a; = 0.0266 ± 0.008 MPa/m depthThe maximum and minimum horizontal compressive stresses, with an average ratio of J.75 ± 0.45, prevail in east-west and northerly directions, respectively. Horizontal compressive stresses in excess of vertical overburden load were determined, indicating large variations in ratios to a depth of about 1000 m with decreasing trend toward depth.From present data, a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined.A common feature at mines with near vertical orebodies is that the maximum horizontal stress acts perpendicular to strike while the minimum horizontal stress is aligned on-strike. The vertical stress components approach the gravitational overburden load."

Jan 1, 1991

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

By L. G. Huntley

I. HISTORY OF OIL DEVELOPMENT IN MEXICO THE occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopote" as a building cement.1 DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de Ias Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 ft. deep was drilled by a company organized in Mexico City, in what is now known as the Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said too have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican, Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State -

Jan 9, 1915

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By G. Jim Cardwell

The question "what constituents should be determined?" is one that defies a simple answer, because earth scientist being what you are, the rock and mineral analyst will eventually be called upon to determine about three quarters of the elements in the periodic table. The concentrations of these analyses will range from as low as 1 ppb to 100% of the material being analyzed. The most important thing to remember about a quantitative analytical result is that it can only be an estimate of the concentration of the analyte present. A measure of the reliability of that estimate is given by statistically derived statements of the precision and accuracy of the measurement. When evaluating your data an understanding of precision and accuracy are of paramount importance. Precision is the measure of agreement between replicate values while the accuracy of a determination is the concordance between it and the true value. There is no quarantee, however, that a precise answer is an accurate one. The numerical difference between the two values is the error. When evaluating your data, the repeats analyzed with your samples will identify the precision and control standards of U.S.G.S. or Canadian Certified Materials quality will identify the accuracy. The main problem is this data is routinely withheld from the report, or was it ever included in the analysis of your samples?

Jan 1, 1983

By E. P. Youngman

The basic mining law of Netherland India is contained in N. I. Statute 1899 , No. 214 , as amended by N. I. Statute 1910 , No. 588 , and 1919 , No. 4 , which is quoted as the " Indian Mining Law, " the effective date of which was fixed as May 8 , 1907 , by proclamation dated October 12 , 1906. The Indian Mining Law was supplemented by Ordinance No. 38 , of 1930 , which was passed by the Volksraad on March 18 , 1930 , to become effective on October 1 , 1930 ( superseding an earlier ordinance entitled " Government Gazette , " 1906 , No. 434) . An important law with respect to American petroleum rights , Statute No. 23 , passed February 9 , 1928 , approving contracts between the Indian Government and the Netherland subsidiary of a large American oil company , is in the nature of a private law or of an enabling act ( see section of this paper entitled " Rights of Foreigners" ) . Statute 1930 , No. 348 , effective October 1 , 1930 , sets forth in minute detail conditions under which prospecting and mining permits may be granted. Statute 1930 , No. 341 , effective October 1 , 1930 , embodies the police regulations of the mining industry.

Jun 1, 1931

By Alvarez A. R, Garcia H. l

A fuzzy expert system, DIME, has been developed, under Matlab v 5.1. to assess the coal and gas outburst risk in underground mining. Expert systems and fuzzy logic are powerful tools to manage information represented by linguistic statements,

Jan 1, 1998

By Na Wang, Chao Du, Yao Zhang Shuqiang Jiao, Hongmin Zhu

"Na2NbAlO5 was synthesized using Nb2O5 and NaAlO2 as raw materials in molten NaCl-CaCl2 by a solid reaction. With an addition of sodium into the melts, Na2NbAlO5 was subsequently reduced to form NbAl3 intermetallic compound with a particle size of 50-300nm.IntroductionThe intermetallic compounds of niobium aluminides have been a subject of research interests as high temperature materials because of their properties such as high melting temperature, large specific strength at elevated temperature, good resistance to high temperature oxidation, low density and large ductility [1,2]. They are applicable for turbine blades in aircraft engines and stationary gas turbines [3,4].In recent years, the methods of powder synthesis have been widely discussed. There are many methods to synthesis intermetallic compounds such as conventional melting and solidification [5], powder metallurgy [6,7], reaction sintering [8] and reaction sintering with prior mechanical activation [9,10]. There is a prominent weakness in such methods that they use metal to produce intermetallic compounds by the means of diffusion reaction. Although the metal can diffusion sufficiently, it is still hard to avoid maldistribution of the constituents which impairs the properties of the materials."

Jan 1, 2012

By A. Qaredaqi, M. Mohammadi

Wet High Intensity Magnetic Separators, for short, WHIMS are used for recovery of Iron ores with low magnetic susceptibility. A Jones patent WHIMS with "grooved plates" matrix is being used in Dry Tailing processing line in Hematite Recovery Plant at Golgohar mining & Industrial Co. for recovery of Hematite. In this kind of separators Matrices are used for increasing the Magnetic field intensity and providing high magnetic field gradient. The laboratory WHIMS in Golgohar Iron Ore and Steel research Institute is capable to provide a background magnetic field strength up to 0.85 Tesla and in presence of ‚expanded metal? matrix, magnetic field intensity could increase up to 0.9 Tesla. More than 50% of feed particles in this separator were finer than 36 micron and recovery of these particles needs more magnetic field intensity. Hence, ‚Grooved Plates? matrices with Js= 2 Tesla and 3.8 mm gap were constructed. Measurements indicated that magnetic field intensity around the matrix will increase to 1.25 Tesla. Graph of Magnetic field intensity around the matrix to background magnetic field intensity was plotted and a model with Rsquare= 0.9 was offered. In addition, magnetic field gradient and magnetic force were calculated. In WHIMS with feed top size of 150 micron, the main effective forces on separation process are the magnetic force and the hydrodynamic drag force. With assuming that the particles are smooth and spherical and the flow is laminar, Recovery of fine magnetic particles is problematic in this separator because of drag force. Considering these facts and mentioned model, finest particles that are recoverable in different magnetic field intensities were calculated. Computations illustrated that with magnetic field intensity more than 0.8 Tesla, particles as fine as 4 micron are theoretically separable but it should be noted that in practice a larger attractable particle size would be expected.

Jan 1, 2014

By F. H. Wilson, E. W. Palmer

The solid solubility of iron in 2 to 10 pct cupro-nickels increases with temperature and nickel content. Property changes accompanying various heat treatments indicate typical precipitation hardening behavior. Iron content also affects softening temperature and sub-scale formation. These factors, as well as impingement corrosion resistance, influence the optimum iron content of commercial alloys. FOR many years Cu-Ni alloys have been used extensively in the form of tubes, pipes, and plates for the construction of salt-water lines and surface condensers on shipboard and in tidewater power stations. The 30 pct Ni alloy has been considered more resistant to rapidly flowing sea water than alloys of lower nickel content, and has been standard on ships of the U. S. Navy. Some ten years ago, the still better corrosion resistance obtained by modifying the 30 pct Ni alloy with approximately 0.5 pct Fe was recognized, and the iron-bearing alloy rapidly superseded the plain alloy as the standard material for severe service. In 1945, Tracy and Hungerford1 published a study of the effect of iron on the corrosion of various cupro-nickels in sea-salt solutions, and their data indicated that the 10 pct Ni alloy containing about 0.75 pct Fe was equivalent to the 30 pct Ni alloy containing 0.5 pct Fe. This was confirmed by LaQue in discussion of the above paper, and by results in an experimental condenser set up at the Kure Beach marine test station of The International Nickel Co., reported by Freeman and Tracy.&apos; The 10 pct Ni iron-bearing alloy is now being very widely used in applications where the 30 pct Ni iron-bearing alloy was formerly considered standard. While this "substitution" has undoubtedly been stimulated by the present extreme shortage of nickel, it must be emphasized that it involves no loss of service performance, and would have occurred anyway in the course of time, for economic reasons. In view of the increasing use of the 10 pct alloy, it seems desirable to make generally available the results of several investigations of Cu-Ni-Fe alloys carried out in the Metallurgical Research Laboratory of The American Brass Co. in recent years. The present paper, deals with the constitution of these alloys in the copper-rich corner of the system, and with the variations in hardness and tensile properties resulting from the heat treatment of alloys containing various amounts of iron. Most of this work is concerned with alloys containing 10 pct Ni. With over about 0.75 pct fe, the 10 pct Ni alloy is suscep- Alloys Several series of cupro-nickel alloys containing iron were used in these investigations. Most of them were prepared in the laboratory, but two samples of commercially fabricated alloys were included. Series A—Nominally 2 and 5 pct Ni, each with 0 to 1.5 pct Fe. Series B—Nominally 10 pct Ni with 0.1 to 0.4 pct Fe. Series C—Nominally 1.0 pct Ni with 0 to 2 pct Fe. Series D—Nominally 10 pct Ni with 3 to 5 pct Fe. Series E—Nominally 10 pct Ni with 1 and 1.5 pct Fe.

Jan 1, 1953