Search Documents

By A. G. Oppegaard

Most iron ores treated by the R-N direct reduction process yield metallic iron products considerably lower in titanium, manganese, and chromium oxides and alkaline metal sulfates/sulfides than were contained in the original ores. These metallic iron products are suitable as feed stock for the open hearth and electric steel-making furnaces. The elements which are rejected in part are acceptable in the product since the product is designed to by-pass the blast furnace. R-N reduction conditions (PCO+H2-1 atmosphere, 1830° to 2150° F.) are adjusted for each ore. The iron ore which is reduced to 90 to 95 percent metallic iron is then subjected to the conventional beneficiation techniques. Under these conditions, 55 to 80 percent of titanium oxides, 75 to 95 percent of manganese oxides, 60 to 90 percent of chromium oxides and up to 97 percent of alkaline metal sulfates contained in the ore are rejected with the gangue to the non- magnetic tailings. The metallic iron products illustrated in this work contained 89 to 96 percent total iron, one to five percent TiO2, 0.2 to one percent MnO, 0.3 to 1.6 percent Cr2O3 and/or up to one percent alkaline metal sulfide. Usually only one of these components was present. Recoveries ranged from 80 to 96 percent of the iron in ore.

Jan 1, 1958

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Jorma Miettunen, Reijo Kalapudas, Pertti Koivistoinen

A new method for measuring the mill filling was developed by Outokumpu’s Pyhäsalmi concentrator during 1989-90. The method utilizes the power draw oscillation which is caused by the mill lifters. Each lifter bar causes a peak in the power draw and thus a continuous oscillation results. In a fixed time scale, the oscillation peaks will shift as the lifter bare hit the mill charge sooner or later depending on the volumetric filling of the mill. Thus the measuring method is based on the phase shift of the power oscillation. So far the measurement is utilized for maximizing throughput of the primary mills at Pyhäsalmi and Enonkoski concentrators and at Harjavalta slag concentrator. The paper describes the new method and the results achieved.

Jan 1, 1992

By Hugo Elcorobarrutia P.

En la industria minera, el óptimo resultado de las voladuras es un factor determinante en la producción y seguridad, siendo elementos indispensables para la vida del obrero. En este sentido, el objetivo del texto estriba en señalar los tiros fallados en las voladuras, a fin de mejorar el rendimiento de las voladuras, como prevenir accidentes. Existen dos tipos de fallas en las voladuras: el tiro soplado y tiro cortado, el primero se produce principalmente por falla en la dosificación del explosivo de acuerdo a la dureza de la roca, mientras que el segundo se da cuando fallan los elementos que intervienen como los fulminantes, la guía de seguridad, y dinamita. siendo este tiro el más peligroso de tratar y del que se mostraran casos y posibles formas de tratamiento.

Jul 20, 1961

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years, Many sophistications of the method have been developed during this time. However, the ability to simulate mathematically still hinges on the ability to ignore unimportant details which would complicate the mathematics and make simulation impractical, Thus, with this attitude in mind, it becomes very easy to design a pseudo- simulator which will predict average conditions very well, but can not truly allow a detailed study of the system being simulated. Most simulations fall into this category, along with the case mentioned here. This paper is not intended to be a critical treatise of the simulator used to study a particular mining system. Instead, it will be used to illustrate the aspects of simulator development. The steps in the development of any simulator are described, along with same detail of the phosphate mine simulator itself.

Jan 1, 1966

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By M. S. Miller, R. H. Mullennex

The growing need for development of thinner, more erratic, or less easily-mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modeling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modeling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities but requires thorough we of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller's logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions may prove more applicable to coal character delineation than mapping of the coal itself. Depositional modeling and trend projection may also serve as a guideline in reserve classification and confidence levels in reserve estimations.

Jan 1, 1983

By Fabricio Reis de Almeida

O presente trabalho tem como objetivo mostrar os ganhos financeiros e produtivos do Laminador de Aços Longos da CSN através da otimização do plano de passes. Analisando a árvore de calibração identificamos a possibilidade de ganhos com a unificação de famílias de bitolas. No laminador temos duas famílias: Família Ø 5,5 mm (bitolas 5,5; 7,0; 9,0; 11,0; 14,30) e Família Ø6,3mm (bitolas 6,3; 8; 10; 12,5 e 16) para a fabricação destas bitolas utilizamos até 18 passes no laminador duo horizontal/vertical e mais ate 10 passes no laminador acabador cantilever. Após um estudo detalhado do plano de passes existente, verificou-se a possibilidade da eliminação e unificação de passes entre as duas famílias. Para corroborar as alterações propostas, decidiu-se utilizar um modelo matemático que representasse os passes e realizasse os cálculos para verificar as reduções e capacidades dos equipamentos visando minimizar os riscos e custos adicionais com modificações de ferramental. Após mais de 60 horas de simulações e testes, foi desenhado um novo plano de passes para a Laminação eliminando-se a necessidade de troca de 8 cadeiras, o que representa um aumento de 6 horas no tempo disponível para produção por mês e também a redução de 8 pares de cilindros de laminação, redução de guias e roletes, e tempo de preparação na oficina de cilindros. Só após verificação e aprovação desta etapa foram iniciados os testes no laminador que confirmaram os resultados obtidos nas simulações.

Aug 16, 2017

By Greenwald, H. P

The Bureau of Mines has been conducting experiments on the explosibility of coal-dust in the experimental mine for more than 17 years. The results have been published from time to time3, and a forthcoming technical paper4 will summarize the results and discuss them in some detail. The present paper will be limited to a statement of the more important facts that these researches have discovered.

Apr 1, 1929

By V. V. Severov, Z. Lafhaj

The flotation separation of salt type calcium minerals is problematic, due to the similarities in their formation properties and the same active Ca2+ related site for interaction with anionic collectors and similar physicochemical characteristics such as solubility, point of zero charge, surface speciation, Ca-site density. The work was performed to achieve effective and selective separation of the calcium-minerals using pure minerals samples: four calcite, two fluorite, and two apatite samples. The effect of pure and mixing anionic collectors such as oleic and linoleic acid to different ratio (2:1; 1:1; 1:2) as well as the role of nonionic collectors on the selective separation of Ca minerals were studied. All flotation tests were performed in self-aspirated flotation cell. The results obtained with the blend of anionic collectors with the molar ratio of 2:1 show a separation between apatite and calcite at pH 5 and a ratio 1:2 at pH 9. The enhancing of separation contrast using the sodium silicate as a depressant for calcite and apatite is also examined as a function of oleate/linoleate ratio. Additionally, this paper discusses the enhancing of the selective separation of Ca minerals when anionic collectors were blended with nonionic reagents. The surface reactions in aqueous mineral suspensions and the adsorption of anionic collectors blended with nonionic reagents were studied by FTIR spectroscopy. An unexpected synergistic effect was observed for some ratios between anionic and nonionic reagents. The mixture of fatty acids and nonionic reagent showed very high flotation efficiency in comparison with fatty acid alone for the flotation of an igneous low-grade phosphate ore.

Jan 1, 2016

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By Alexander Pomerantsev

In recent years, bucketwheel excavators have found wide application in open pit surface mining not only because of their large production capacities, but also because they easily lend themselves to automation. Krupp, Orenstein & Koppel, Buckau-Wolf, Mechanical Excavator, Lauchhammer, Manufacturers in Eastern Europe designed and installed many models of bucketwheel excavators that can excavate any type of materials, could be used in any climate conditions and for any type of technological schemes in open pit surface mining, (Photo I, II and III)

Jan 1, 1979

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By A. R. MacPherson

The procedure to arrive at an energy efficient autogenous grinding plant is carried out in the following steps: First Step - Determine power requirements to grind a particular ore. This work carried out on small samples ground in a 450 mm diameter Aerofall Hill and the results are checked against a standard Bond Index test. Second Step - A bulk sample from the ore zone is ground in a 1.8 m diameter pilot mill. This work is carried on until the power objectives as indicated from the first step have been realized. Third Step - Correlate the pilot mill data, with the data from the numerous samples ground in the small 450 mm mill and arrive at design criteria for the commercial plant. Ensure commercial mill design will be suitable to obtain similar results as those obtained in the pilot mill.

Jan 1, 1981

By John C. Carpenter

Solvent extraction is used to selectively recover copper from iron containing sulphate solutions. As chloride ions, which form series of complexes with transition metals, are now being used for leaching. Little is known of the effects of these ions, on solvent extraction behavior. It has been shown that commercial extractants of the L1X and Kelex series extract copper from chloride media: (1) at a lower pH than from sulphate solutions, (2) to similar loadings, and (3) except for L1X 63, without transferring chloride to the organic phase. A process for selective extraction of copper from chloride solutions should thus be compatible with standard stripping and electrowinning practice. Of several diluents, differing in aromaticity, kerosene gave enhanced extraction only with L1X reagents. A change in operating temperature had little effect on equilibrium metal distribution. All the extractants examined gave adequate separation of copper from iron. L1X 63 was found to extract chloro-complexes of copper and of iron and thus transfer chloride to the organic solution. Consequently this extractant and its mixtures are not preferred for use with chloride leaching systems.

Jan 1, 1976

By W. A. Zingg

Impervious zones in copper waste heaps create a problem in contacting the rock with leaching solutions. These zones are normally associated with compacted layers .formed on the surface of each lift by dump truck traffic and by disintegration of the rock exposed to atmospheric conditions. These layers are usually only a few feet in depth--but, nevertheless, act as barriers to vertical flow causing the leach solution to perch in the heap, Consequently, much of the rock remains untouched and the leach solution breaks out the side of the heap instead of continuing downward to bedrock. One solution to this problem is breaking the hard pans with explosive charges. However, to use explosives means adopting new explosive materials and methods. To use this process successfully requires finding answers to operating conditions inherent to waste heaps. Foremost among these are: (1) type and size of casing that can be used because of limitations brought about by drilling problems, caving and, corrosive conditions; (2) perforating the casing at required levels; (3) an explosive capable of being pumped; (4) obtaining detonation of the, main charges through, the wail of the casing; (5) an explosive with the ability to propagate through the voids of the rubble and one which is not affected by water, acidic solutions, or back pressure conditions from hydrostatic heads; (6) to heave and rupture the compacted zones without chambering or recompressing the waste material.

Jan 1, 1970

By R. L. Stanton

"The present contribution is complementary with a preceding one on the field association of the conform-able ""pyritic"" deposits. It considers the more important features of their mineralogical constitution and their microtextures, re-examines the present interpretations of these, and of-fer-some alternative explanations. The term ""pyritic"" for these de-posits is m many cases a misnomer, as two quite distinct ore types are inuolve. One is a banded pyritic sphalerite-galena-chalcopyrite ore (for which the term '•pyritic"" is in-deed quite suitable), while the other is non-banded and is composed essentially of pyrrhotite and chalcopyrite. In addition to these constitutional differences, each is distinctive in general appearance and texture. The occurrence of two such consistent but clearly distinguishable ore types is attributed -rather than to difference in source material and pressure-temperature conditions of deposition -to the contribution of similar source material to dissimilarly oxygenated environments of sedimentation. Textures in the banded ores generally thought to be indicative of replacement or of high-temperature exsolution are explained by slow, law-temperature segregation in situ during compaction, folding, and regional metamorphism."

Jan 1, 1960

By Stewart W. Daniel

Competitive pressures involving product duality, uniformity and economics are increasing the interest in and accelerating' the adoption of automation by the cement industry. The demands of this industry on instrumentation and control manufacturers for more effective and reliable control of process variables is also increasing. The trend to replacing small grinding mills with a fewer number of larger mills is lowering the investment requirement per unit of capacity both for the mills and for their automation. Cement process control systems of today are more sophisticated than the equipment installed two or three years ago, not because the process itself is more complex but because todays demands require a higher degree of control action and accuracy. Because of increasing labor costs, an important objective of an automation program is a reduction in the process labor content. This can be realized by allowing the operator free time for other duties, by increasing the number of grinding circuits one operator can supervise and by removing to. a large extent the need for the operator to make process' adjustment decisions.

Jan 1, 1965

By Z. T. Bieniawski

Results of in situ investigations are discussed providing comparisons of rock mass deformability measurements by three methods: 'petite sismique' technique, the Goodman borehole jack and flat jacks. The tests were performed in exploratory tunnels constructed for site characterization purposes of an underground hydro-electric scheme. Due to the large number of data (41 petite sismique measurements, 45 Goodman jack tests and 19 flat jack measurements), it was possible to evaluate thoroughly the testing techniques employed. The purpose of this paper is to indicate the problems encountered in the interpretation of the results and to offer suggestions for selecting in situ tests. INTRODUCTION In situ tests are expensive and time consuming but they are an important aid in tunneling applications since they can provide deformability data of rock masses in contrast to rock material characteristics obtainable from small laboratory specimens. Some in situ tests are relatively easy to perform but their reliability may be in question unless a comparison of the data obtained by several different test methods is possible. Although many in situ techniques are available for determination of rock mass deformability (1), those more convenient to use are the Goodman jack, flat jacks and 'petite sismique. These methods are considered convenient because the Goodman jack is a borehole device; flat jacks can provide not only deformability data but also information about the stress field around excavations; while 'petite sismique' is based on seismic refraction surveys. Accordingly, these three methods have been selected for comparison.

Jan 1, 1979