Search Documents

By Gordon Matheson, Bill Yancey, David K. Miller

"Current regulatory limits for blast vibration and airblast control in Virginia do not specifically addressunderwater explosive testing. Underwater detonation of explosives generates an initial shock wave and a gas bubble. The gas bubble expands and collapses several times before reaching the water surface. This expansion and collapse of the gas bubble as it rises to the surface is called a “bubble pulse”. The bubble pulse generates low frequency vibrations that have the most potential for damaging structures and causing blasting complaints even below damage levels."

Jan 1, 1999

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By R. F. Dickerson, D. A. Vaughan, A. F. Gerds

ALTHOUGH the metallurgy of uranium has been under intensive study since the early 1940's, no systematic effort has been made to identify the non-metallic inclusions in uranium. Uranium carbide (UC), which is probably the most common inclusion found in graphite-melted metal, has been tentatively identified by previous investigators, but the other nonmetallic inclusions have received little attention. Since metallography is a valuable tool in metallurgical studies, the metallographic identification of the nonmetallic inclusions in uranium is important. Such an investigation has been completed and the identification of slag-type inclusions and of uranium monocarbide, uranium hydride, uranium dioxide, uranium monoxide, and uranium mononitride is described. Metallographic Preporation It is often possible to prepare specimens for metal-lographic examination equally well by several methods. The specimens which were examined in this work were prepared by one of two acceptable methods. For the convenience of the reader, both methods will be discussed in detail and will be referred to simply as Method I or Method II in the subsequent sections. For both Methods I and 11, specimens for microscopic examination usually were mounted either in bakelite or in Paraplex room temperature mounting plastic. Method I—Specimens were ground in a spray of water on a revolving disk covered successively with 120-, 240-, and 600-grit silicon carbide papers. It was necessary to perform the final grinding operation carefully on worn 600-grit paper to keep the scratches as fine as possible. After washing and drying, the specimens were polished for 3 to 4 min on a slow speed wheel (250 rpm) covered with a medium nap cloth. Diamet Hyprez Blue diamond polishing paste, Grade 00, 0 to 2 µ, was used as abrasive with kerosene as lubricant on the wheel. Specimens were washed thoroughly in alcohol and final polished electrolytically in an electrolyte composed of 1 part stock solution (118 g CrO, dissolved in 100 cm3 H2O) with 4 parts of glacial acetic acid. A stainless steel cathode was used. At an open circuit potential of 40 v dc, a polishing time of 2 sec retained inclusions well with the bath at room temperature. If additional etching was required to sharpen the interface between the metal and the inclusions, an electrolyte composed of 1 part stock solution (100 g CrO3 and 100 cm8 H20) and 18 parts glacial acetic acid was used at room temperature. Best results were obtained by etching for from 10 to 15 sec at 20 v dc in the open circuit. Surfaces obtained by this method are suitable for microscopic examination. However, if desired, they may be etched further with other chemicals. Method 11—Rough grinding was done on a wet 180- or 240-grit continuous grinding belt. The specimen was then ground by hand successively on 240-, 400-, and 600-grit silicon carbide papers in a stream of water. Final polishing was accomplished on a 4 in. high speed wheel (3400 rpm) covered with Forstmann's cloth. Linde B levigated alumina, suspended in a 1 volume pet chromic acid solution, was the abrasive. Specimens usually were polished in 5 min or less by this technique. Often the inclusions present in the metal were identified in the mechanically polished condition. When etching was required to outline inclusions more sharply, one of the two following methods was used. In the first method, the specimen is etched lightly while electropolishing in the chromic-acetic acid solution described above (1 part of stock solution to 4 parts of acetic acid). The electrolyte was refrigerated in a dry ice-ethyl alcohol bath and specimens were etched at 60 v dc on the open circuit for 2 or 3 cycles of 3 to 4 sec each. The second technique utilizes electrolytical etching at about 10 v dc (open circuit) in a 10 pet citric acid solution at room temperature. X-Ray Diffraction Technique The major problem in the identification of inclusions in metals by X-ray diffraction techniques is the extraction of a sufficient amount of each type of inclusion to obtain an X-ray diffraction pattern. In the present study, X-ray diffraction patterns were obtained from individual inclusions of the order of 10 µ diam. The polished and etched samples shown in the micrographs were examined at a magnification of X54 or XI00 with a binocular microscope. This allowed sufficient working distance to extract the inclusions with a needle probe for powder X-ray diffraction analysis. Friable inclusions such as MgF2, CaF2, UO2, and UH3 could be freed from the metal by probing the as-polished and etched surface. The fine particles then were picked up on the end of a Vistanex-coated glass rod (0.002 in. diam) which was held in a brass adapter made to fit the powder X-ray diffraction camera. The end of the glass rod was centered in the path of the X-ray beam. In the case of the UC, UO, and UN inclusions which are smaller in size, more metallic in appearance, and less friable than the other inclusions, it was necessary to etch the inclusion in relief before extraction. UN inclusions etched sufficiently in relief in the electrolytic polishing solution described in Methods I and II by increasing the polishing time. UN inclusions were relief etched by extending the

Jan 1, 1957

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By Henry Louis

Four alloys of gold and silver were prepared, containing the metals in the following proportions by weight: I. Gold:Silver::1:2.62.

Jan 1, 1894

By Marie-France Caille, Carl Caumartin

"Audrey Resources' Mobrun Mine is located in Dufresnoy Township some 30 km to the northeast of Rouyn-Noranda. The Mobrun tine deposits consist of two major massive sulphide lenses; the newly discovered 1100 lens located 450 m south of the Main zone, and one ntellite lens, the 850-870-930 complex.The 1100 lens is hosted in a large pyroclastic unit bounded to the mouth by rhyolite and andesite flows and by a thick rhyolite unit to the art h. stratigraphically belon the three lenses. It consists of approximately 15 Mt of massive sulphide, of which 10.4 Mt are of economic ade. The Main lens lies comformably above thick rhyolite flows, ecciated and pyritized by the sulphide horizon, and is overlain by ttercalated ash tuffs and rhyolites which host the over-lying satellite ns. The Main lens consists of 3,3 Mt of massive sulphide, of which 523 000 tgrade0.80% Cu, 2.44%Zn,30.19 g/t Ag, and2.2 g/t Au he richer satellite lens (180 000 t) is part of the same volcanic stem and resulted from a resurgence of hydrothermal activity. ructure played a role in the final geometry of the deposits but did not eatly affect the volcanogenic and stratabound nature of the lens. Total production since the start of operations in 1985 amounts to 58 000 t and is restricted to the Main lens. Production from the 100 will come onstream in 1992 as ore reserves from the Main and e satellite lenses are exhausted.RESUMELa Mine Mobrun de Ressources Audrey inc. est située dans le mton Dufresnoy, a quelque 30 km au nord-est de Rouyn-Noranda. lle comprend deux lentilles de sulfures massifs d’importance majeure ~i sont les lentilles 1100 et Principale, et une lentille satellite qui est complexe 850-870-930.La lentille 1100, la plus ancienne, est contenue dans une épaisse 1ite pyroclastique bordée, au sud, par des coulées de rhyolite et d’andésites, au nord, par une épaisse unité rhyolitique. Cette lentille contient environ 15 Mt de sulfures massifs dont 10,4 Mt à teneur économique. La lentille Principale repose sur d’épaisses coulées rhyolitiques brechifiees et pyritisees à proximité de l’horizon de sulfures; elle est recouverte de tufs a cendres et de rhyolites interlitees qui contiennent la lentille satellite. La lentille Principale est constitute de 3,3 M t de sulfures massifs dont 1 523 000 t sont économiques avec une teneur moyenne de 0,80% Cu, 2,44% Zn, 30,19 g/t Ag, et 2,2 glt Au. Faisant partie de ce second épisode volcanique, la riche lentille satellite (180 000 t) temoigne d’une recrudescence de l’activité hydrothermale. La structure joue un rôle important dans la géométrie finale des dépôts mais ellen' affecte pas, de fa~on significative, la nature volcan génique des lentilles. Depuis le début des opérations, en 1985, la production totale est d’environ 568 000 t, provenant essentiellement de la lentille Principale. La mise en production de la lentille 1100 est prévue pour 1992, alors que les réserves des lentilles Principale et Satellite seront probablement épuisés."

Jan 1, 1990

By Fred W. Gordon

It is my purpose to call attention to the close approximate correctness of certain coefficients and formulas concerning the flow of gases, and their applicability to the practical construction of flues and

Jan 1, 1886

By M. B. Cortie

An account is given of the development of ferritic stainless steels since their discovery in the early years of this century. The alloys became very widely used in the 1950s, the market during that decade being driven strongly by a demand for automobile trim made of ferritic stainless steel. The production of ferritic stainless steel declined as a proportion of the total at the end of the 1950s as consumer preferences changed. However, the market is now growing strongly again, this time driven by a demand for oxidation-resistant alloys for motor-vehicle exhaust systems. The tonnages produced, applications, and market shares of the various alloys are discussed and compared. Trends in world stainless-steel production, product forms, technological development, and usage are examined.

Jan 1, 1993

By Milan Lj. Stamatovic

The hydrometallurgical recovery of zinc from recycled blast furnace dust from a steel plant (Smederevo Metallurgical Company, Yugoslavia) was investigated. The dust contained 22% Fe, 17% Zn and 0.2% Pb. X-Ray diffractometry showed that the main components were hematite and magnetite, in combination with zinc oxide. Individual particles were generally spherical and ranged in size from 10 to 150 microns; 63% were less than 33 microns in diameter. An effective hydrometallurgical approach proved to be by caustic leaching and electrowinning. Recovery of zinc in the form of zinc powder was over 90%; this material can be used for the cementation of impurities in the conventional hydrometallurgical process for zinc production.

Jan 1, 1994

Early American history is filled with records of the search for and extraction of minerals-a Northwest passage to the treasures of the Indies-an overland route to the goldfields of California. Mining and its associated minerals industry have heralded advancing civilization throughout the ages. The two basic resources on which we all depend for our food, clothing, shelter, and other comforts are agriculture and minerals. Our endowment and how we use it; the spirit and industriousness of our people; our form of social organization all converge to make up our standard of living-our way of life.

Jan 1, 2012

By T. Yun

The process automation of coal production is one of the important component parts for achieving the modernization of coal industry. To realize the coal mining process automation serves the significant, function of increasing productivity, improving the quality control of raw coal, making efficient use of mineral resources, saving energy and is of great importance in enhancing the safe operation and improving the labour conditions as well.

Jan 1, 1989

By J. P. Remi Proulx, Juan Camilo Gonzalez T., Winston B. Wilches

Alabama USA based Drummond Ltd. operates two open pit mines in the Cesar Coal Basin of Northern Colombia. The mines produce a combined total of over 25 million tons (22.7 Mt) of thermal coal per year which is transported by rail to Puerto Drummond, a direct ship loading facility, where it is exported to over 15 countries. The company has proven and probable reserves in excess of one billion tons of thermal coal.

Jan 1, 2015

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By Shuli Teng, Vladimir Sujansky, Matthew Rawls, Ivan Junarsa

In recent years significant advances have been made in chemical processing technology. In particular, process intensification using micro-technology has had some success in changing and improving chemical processes including mixing. Process Intensification is the miniaturization of unit operations and processes whereby a smaller compact piece of equipment takes the place of a larger one at the same given capacity or mass flow rate. This paper summarizes research into the application of the technology for manufacture of high internal phase water in oil ammonium nitrate emulsions (ANE’s) at low energy cost and with very low oil/fuel blend content. The emulsions can be used as precursors for preparation of explosives. The quality of the emulsion prepared was assessed through droplet and crystal analysis and compared with that of emulsions made by conventional large scale jet mixing technology.

Jan 1, 2014

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998

The incidence of colliery disasters has highlighted the need for more centralised and directed coal mining safety research in Queensland, with particular impetus from explosions at Box Flat in 1972, Kianga in 1975 and Moura No 4 in 1986. Inquiries which identified the likely causes recommended measures and, research and two outcomes have been the present Mines Safety Research Advisory Committee and The Safety in Mines Testing and Research Station at Redbank, near Brisbane, dealing with all mining problems, coal and metalliferous. Already, important research into ignition and explosion and other health and safety matters has been accomplished; the Station has become an accredited testing laboratory; and international recognition has been achieved. Now the advisory, testing and research arms are soundly in place to pursue preventive investigations and be ready to provide assistance in any emergencies.

Jan 1, 1991

Achieving continued economic growth with social equity within the natural limits of the Earth's 'eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By Edward S. Frohling

Va a ser discutida la información que se requiere para un estudio preliminar de viabilidad y la información adicional que se requiere para el estudio final de viabilidad de un nuevo depósito de mineral. El estudio preliminar de viabilidad se realiza con muy poca información y con un mínimo coste para el propietario. Sin embargo, el diseno del informe preliminar es similar al utilizado para el informe final. En este momento, se supone que el resultado del estudio preliminar es favorable y el propietario autoriza el estudio final de viabilidad a una compañía de ingeniería. Se describirá el tipo de organización para completar el estudio final de viabilidad. El informe final incluirá toda la información y datos relativos al nuevo depósito de mineral. La información presentada debe ser entendida lo mismo por el personal financiero que por el técnico.

Jan 1, 1982