Search Documents

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By A Poliakov, E Donskoi, K Vining

The automated optical image analysis software Mineral4/Recognition4 (M4/R4) is capable of performing comprehensive characterisation of different materials throughout the iron ore value chain, including ore fines, lump, sinter, pellets and coke. It has been successfully used by CSIRO for industrial and research projects and has been independently licensed to several world leaders in iron ore production and ironmaking. The M4/R4 software was strongly integrated with a Zeiss microscope to make use of the company’s powerful AxioVision software. This required users to own both Zeiss microscope hardware and AxioVision software in order to be able to use M4/R4 to its full image acquisition and analysis capacity. Therefore, it was not available to the users of equipment produced by other major microscope manufacturers. In recent times however, Zeiss has indicated that the AxioVision software will no longer be supported. To overcome this limitation, CSIRO has proceeded with the next generation of this software, Mineral5/Recognition5 (M5/R5). Importantly, the M5/R5 system has been developed without any dependence on a specific microscope hardware/software platform. Furthermore, the image analysis functionality is now based on openCV open access software and has been fully rewritten using stateof- the-art software development tools to allow reading and processing of all major image formats. Although past applications have been specific to iron ore and ironmaking applications, other improvements, such as an increased number of minerals allowing better gangue segmentation, flexible mineral definitions, improved software modules behaviour and refined analysis routines enables the platform independent M5/R5 image analysis system to be used by researchers in any area of mineralogical or materials research.

Nov 8, 2021

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

By Jenny Alsén, Hans Hogard

"Construction of large facilities underground in urban areas has many advantages. In order to show the advantages, a case study of the Norsborg metro depot in Stockholm Sweden has been made. The Norsborg metro depot will be the largest and most modern underground metro depot in northern Europe. The depot has been built in hard rock in an urban area with small impact on the environment and local residents. The paper describes how it is possible to build underground facilities in a cost efficient way and take care of the challenges regarding working environment that comes with locating a permanent working place underground. INTRODUCTION The Stockholm area is one of the five fastest growing regions in Europe and home to more than a fifth of Sweden's population on just two percent of Sweden's surface. The population is growing rapidly, with about 35,000 people per year and is expected to reach 2.6 million in 2030. In order to meet the development and enable continued growth, housing projects and expansion of infrastructure need to keep the same pace; this is an easy conclusion to make but much more difficult to realize in practice. The main challenge is to accomplish development in a sustainable and efficient manner, minimizing the use of resources and land. By constructing facilities underground more urban space will be made available for development and/or for greening of city centers. Considering sustainability factors such as land value in decision making for placing of structures or facilities, underground locations could become a first choice alternative. During 2015 and 2016, several major underground infrastructure projects in the city of Stockholm will start, including a 14 km sewage tunnel and an 18 km by-pass highway tunnel. Furthermore the Stockholm metro system is currently undergoing the largest expansion since the 1970’s, a 19 kilometers extension of the metro system including new trains and new stations is planned. During 2013 - 2015 Skanska Sweden took part in the construction of a new metro depot placed underground in the southern part of Stockholm; the Norsborg metro depot. This is a top modern urban underground facility that in 2017 will serve as depot for 17 new metro trains. The project was selected for “Outstanding Project of The Year” at the ITA Tunneling Awards 2015."

Jan 1, 2016

By H. H. Alexander

In the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. In 1900 the number of bags was again increased, making a total of approximately 2,800. The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting, As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 1, 1915

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

By A. S. Callen

These iron mines of Spain are located on the mountain ridge forming the boundary between the Teruel and Guadalajara provinces, called Sierra Menera. They form a property of 25 mines extending over an area of 1,677 hectares (4,140 acres) situated at a height varying from 1,200 m. (3,940 ft.) to 1,500 m. (4,920 ft.) above sea level. The deposit follows the direction north to south; huge masses of ore are being found both on the slopes and at the summit of the Sierra. The ore occurs among quartzites and magnesite limestone, in some places overlaid by quartzite 15 m. (50 ft.) thick; in some others (and this is more general) the ore is overlaid by earth and boulders of quartzite origin; this layer is about 8 m. (26 ft.) thick. The ore beds occupy the geological horizon of the Superior Trias or Muschelkask, which are here in direct contact with the Silurian quartzites. The lime-stones have been more or less transformed. There is ample evidence to show that these mines were worked in very ancient times—objects and tools employed in mining by the ancient Romans and Arabs are to be found plentifully in old workinigs which extend down into the deposits. It has been estimated that more than 10,000,000 tons of ore were mined in the old days in this district and carried to the primitive forges in the vicinity where iron of much renown in Spain was extracted. Remains of more than 20 of these forges are found in the neighborhood of Sierra Menera and are usually situated near waterfalls and forests. Much investigation has been carried on for the purpose of determining the quantity of ore to be found in these mines, but no exact calculations can be made at present. When the investigation is completed it will surely be found that the deposit contains a much larger quantity than the 100,000,000 tons indicated by the present workings. The mines are now worked as open quarries and this method can and will be followed for a long time, probably until the deposit is worked out. Figs. 1 and 2 give some idea of the quarries in operation and the reserves, the iron-ore stocks, screening installation and general arrangement. From these quarries 1,000,000 tons can be mined annually (987,000

Jan 1, 1916

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920

By R. E. Wade

THE Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. &. P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at. either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 11, 1913

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By Xue Ping

Sm2Fe17 alloy is an important precursor for the preparation of Sm2Fe17Nx magnet, which possesses a higher Curie temperature, larger anisotropy field, better resistance to oxidation and thermal stability. In this paper, the wet chemical co-precipitation was developed for synthesis of the Sm-Fe alloy oxide precursor. Based on the principles of simultaneous equilibrium and mass balance, a series of thermodynamic equilibrium equations of Sm(III)-Fe(II)-NH3-C2O4 2--H2O system at ambient temperature were deduced theoretically and the thermodynamic diagrams of lg[M2+]T (M=Sm, Fe) versus pH at different solution compositions were drawn. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH value, reactant concentration, reaction temperature and aging time, etc. It is found that by precise control of the process, the Sm-Fe alloy oxide precursor was synthesized with fine crystallization and special size &size distribution.

Jan 1, 2008

By Deno M. Pappas

The objective of this Bureau of Mines investigation was to identlfy and evaluate alternative binder materials for use in stabilizing and consolidating highly fractured roof along longwall faces and gate roads. The desirable characteristics of a stabilization material were defined, and an extensive search was conducted to find materials satisfying these characteristics. Of 20 materials originally scrutinized, 9 were chosen for laboratory analyses. The laboratory tests evaluated bond strength and tensile strength under both dry and wet conditions. An optimum material was not found. The laboratory analyses indicated two possible candidate materials for longwall stabilization: high-aluminous cement and two-component epoxy; however, the tensile strength of the high-aluminous cement was mediocre, and the epoxy cement is toxic, flammable, and fairly expensive. The potential market demand for an effective and economical stabilization macerial is discussed in the appendix.

Jan 1, 1988

[Separates of all the Technical Publications published in 1929 are available at lnstitute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions.] Metal Mining Technical Pdbli- Title Author Meeting Trans. cation . Volume No. and Page* 182-A-23 The Royal Commission on Mining Henry Louis New York Subsidence Feb., 1929 183-A-24 Cycles in Metal Production D. F. Hewett Nen. York T29, 65, 95 Feb., 1929 199-A-25 Ventilation at the United Verde Oscar A. Glaeser New York T29,- 114. Mine Feb., 1929 206-A-26 Air Conditioning In Deep Mines R. W. Waterfill New York T29. 99, 112 Feb., 1929 245-A-27 Bumps in No. 2 Mine, Springhill, Walter Herd New York Nova Scotia (with discussion) Feb., 1929 257-A-28 Misfires: Their Causes, Prevention New York and Treatment on Occurrence Feb., 1929 Misfires in Anthracite Coa1 T. D. Thomas Mines (With Discussion) Misfires in Bituminous Coal W. H. Forbes Mines (With Discussion) Misfires in Non-metallic Mining A. W. Worthington (Limestone) (With Discussion) Milling and Concentration 195-B-15 A Study of Differential Flotation C. R. Ince New York Feb., 1929 196-B-16 Elements of Operation of the Arthur F. Taggart New York Pneumatic Table H. L. Lechmereoertel Feb., 1929 202-B-18 Silver-bearing Minerals of Some A; W. Habn New York T29, 325 Ores from Tintic Mining District Feb., 1929 204-B-17 Experiments with Flotation Re- A. F. Taggart New York agents T. C. Taylor Feb., 1929 C. R. Ince 208-B-20 Cyanide Regeneration or Recov- C. W. Lawr Sun Francisco ety as Practiced by the Com- Oct., 1929 pania Beneficiadora de Pachuca, Mexico 214-B-19 Calculations in Ore Dressing W. Luyken New York E. Bierbraer Feb., 1929 217-B-21 Differential Grinding Applied to Leon M. Banks San Francisco Tailing Retreatment George A. Johnson Oct., 1929 224-B-22 Reducing and Oxidizing Agents Research Staff San Francisco and Lime Consumption in Flo- of United Verde Oct., 1929 tation Pulp Copper Co. 247-B-23 Copper Sulfate as Flotation Acti- 0. C. Ralaton San Francisco vator for Sphalerite 0. R. King Oct., 1929 F. X. Tartaron

Jan 1, 1929

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By P. D. I. Honeyman, P. A. Faust

At the Miami plant of the International Smelting Co., Inspiration, Ariz., there are four reverberatory furnaces, all 120 ft. long. At present only one of these furnaces is in operation. It is operated as a wet-charge furnace, the charge being distributed for about 65 ft. down the furnace length. Usually this charge contains about 12 per cent moisture and runs 25 per cent sulfur, of which there is eliminated in the furnace from 25 to 30 per cent. The furnace is oil-fired, the fuel being burned in a battery of Cananea-type, low-pressure burners. The flame is kept short and conditions so adjusted as to obtain complete combustion within the furnace. The average furnace draft, taken through the verb arch, amounts to only 0.02 in. of H2O. Draft is purposely kept low to cut down infiltration through the flues and boiler settings, and control dampers are regulated to maintain this uniform condition throughout the charging as well as the smelting period. Hot gases discharge from the furnace uptake through a common header flue to the waste-heat boilers. The general layout and dimensions of the plant are shown in Fig. 1. Four Stirling boilers, two of class M-26 (713 hp.) and two class M-31 (850 hp.), serve the furnace. Three usually are sufficient to take care of normal operation, the fourth boiler being used as a spare when necessary. The distribution of hot gases to the various boilers is regulated by the dampers in the boiler exit flues. Normally the boilers closest to the furnace uptake would evaporate more water than do those farther away, but dampers are regulated so as to distribute fairly well the load between the several boilers. Steam from the waste-heat plant is delivered to the adjoining power house of the Inspiration company, where it is used both in the Nordberg blowing engines and for electrical generation. Steam pressures and temperatures recorded are those in the main power-plant header and are thus inclusive of all losses in about 500 ft. of 10-in. line. Steam for smelter heating and auxiliary use is taken from the main waste-heat header, is reduced to 125 lb. and distributed through separate lines. Boiler feed water is supplied by the power plant and consists of returned condensate, augmented to a large extent by make-up water

Jan 1, 1934

By Paul C. Miclea

In case of a major fire in a tunnel between stations or ventilation shafts, if the buoyancy effect of the hot gasses is stronger than the airflow induced by the fans, the risk of backlayering could restrict the safe evacuation of people. Obstructions in the tunnel and alternate airflow paths can further reduce the air velocities past the fire. Currently there are two computer programs available to address the issue of underground fires: o "Subway Environment Simulation" (SES), Version 3.0, developed by Associated Engineers, a Joint Venture of Parsons Brinckerhoff Quade & Douglas, Inc., De Leuw Cather & Co., and Kaiser Engineers, Inc. for the U.S. Department of Transportation o "MFIRE", Version 1.26, developed at Michigan Technological University for the U.S. Department of the Interior, Bureau of Mines. As implied by its name, the SES program was developed specifically for the analysis of subway ventilation systems. It can be used to analyze the heat released into, and removed from, a subway or vehicular tunnel and to determine the effect of ventilation elements on airflows throughout the network of stations or other merging tunnels. It has a special feature allowing the user to predict the effects of a fire at any location within the subway system. Version 3.0 of the SES program is designed to be used with a "critical velocity" calculation in order to determine whether or not tunnel airflows can be controlled during a train fire emergency. The original version of the program was written in FORTRAN for mainframe computers, such as the IBM 4381. Recently ICF Kaiser Engineers has compiled a version of the SES program for PC use. The MFIRE program simulates the interdependence between a mine ventilation system, with its pertinent fans and structures, and changes in ambient conditions or a source of heat, such as a fire. It also accounts for natural ventilation. The program is written in FORTRAN 77 and compiled for 8086/8088 based microprocessors, allowing it to be run on an IBM PC or compatible computer with a 2.0 or a later version of DOS, 256K random access memory (RAM), and a text editor. This paper reports the comparative results of an application of both programs for the same network in a recent study.

Jan 1, 1991

By R. G. Knickerbocker

THE copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and. terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers.

Jan 1, 1932

By Rudolf Kudlich

"The realization that fuel costs, high as compared with those enjoyed prior to the war, are apparently permanent, has caused steam power plant operators to apply their best efforts towards improving the fuel economy of their plants.Though they have given much attention to the reduction in combustion losses by improving methods of firing and improved equipment, and to diminishing the heat losses by more care in maintaining clean heating surfaces and tight and adequate baffling, they have almost universally neglected the waste that occurs from discarding unconsumed combustible with the boiler refuse.This loss varies between extremely wide limits, depending on the quality of the coal, the type of plant and the firing practice in general, the higher the ash content of the coal the greater will be the amount of combustible appearing in the refuse, and the losses will be greater as the boilers are driven at higher ratings. The refuse from stoker fired boilers is apt to have a lower aver-eve percentage of combustible than that from hand fired boilers if operated at the same rating, but stoker fired boilers are usually pushed to higher ratings and the combustible in the refuse will run higher.In actual operating practice the amount of unconsumed combustible in the boiler refuse may range from a few percent to as high as forty or fifty percent. In an informal statement one well known combustion engineer estimates that the average amount of combustible in the refuse from a large stoker fired central station boiler plant is about 15 or 20%. Assuming that the coal burned contains 12% of ash, and allowing for flue dust losses, approximately two percent of the coal will be lost through this channel. The operating engineer of one large modern central power plant reports that when burning coal of about the same ash content, the average amount of combustible in the refuse was in the neighborhood of 33%, en tailing a loss of approximately 4% of the heating value of the fuel fired. Where the coal used daily runs up into hundreds of tons, an appreciable economy could be effected by recovering this percentage."

Sep 1, 1924

By E. Cortese

Phosphate occurs in many places in Egypt, in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the camel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following that track, after having crossed the watershed, underlain by rocks like granite, serpentine, porphyry, and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil, and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Aures-sensis Coq. sp. = R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismaely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconform-ably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 1, 1918