Search Documents

By Bernard L. Cohen

INTRODUCTION The most serious occupational radiation episode in U.S. history was the exposure of uranium miners to radon daughters in the 1945-1968 time period. Although the maximum permissible dose at that time was 12 WLM (working level months) per year, average exposures were several times that figure, and ten times higher exposures were not uncommon. Starting in the early 1960s, mounting epidemiological evidence appeared for an excess incidence of lung cancer among these miners; up to 1974, there was an excess of 134 cases (159 observed vs 25 expected) among the 4000 in the group under study (NAS-1980). When this excess became apparent, the Federal Government took jurisdiction, greatly tightened enforcement, and in 1969 lowered the maximum permissible exposure to 4 WLM per year. These standards were met largely by a great improvement in ventilation. As a result of these measures, average miner exposures were reduced 5-fold from 1965 to 1968 and by another factor of 3 by 1970. In 1978, the 4 WLM/year maximum permissible exposure was exceeded by only 37 of 7500 underground miners, for only 16 wars it exceeded by more than 25%, and for only 8 was it exceeded by 502 (AIF-1980). The average exposures to the various groups are listed in Table 1. We see that the average exposure for all miners was 1.03 WLM, and for those who worked essentially full time underground it was 1.45 WLM. For purpose of later discussion, it will be convenient to choose a single value for average exposures. In view of the fact that employment situations and job categories are bound to vary over a lifetime of work, we take this to be 1.3 WLM/year. The purpose of this paper is not to dwell on history, but rather to address the question of whether or not this present situation is satisfactory. This question was considered recently by a study group under the auspices of National Institue of Occupational Safety and Health (NIOSH-1980) and it answered the question in the negative, concluding that the maximum permissible exposure should be substantially reduced. However, their arguments were incomplete and were lacking in perspective. The principal thrust of this paper is to provide some of the material overlooked. RISK TO URANIUM MINERS FROM RADON EXPOSURE In order to quantify the risk to uranium miners under present working conditions, it is first necessary to estimate the risk of lung cancer per WLM of exposure. The most straightforward way of doing this is to use the data on the group of uranium miners under study. These are listed in Table 2 for 8 exposure ranges and for the total group (NAS-1980). If all data are given equal weight, the risk is seen to be 3.5 x 10-6 per year per WLM. Much can be said in favor of using this value for the risk as dose independent; it is within one standard deviation (SD) of the observations in 5 of the 8 dose categories (as expected from the definition of SD), and within 2 SD for all 8, and for the three cases differing from the mean by more than one SD, two are above and one is below. However, the uranium miner exposures in the present situation will be far below those covered in Table 2, so it is worth considering the possibility that the risk differs from this at low doses. From the last column of Table 2 we see that the experience from all exposures below 600 WLM indicates a risk higher than the mean for the entire group by more than two standard deviations (the value 600 WLM in this comparison was deliberately chosen to maximize this deviation; for exposures below 360 WLM and 840 WLM, the excess is only 1.0 and 1.6 standard deviations respectively). In view of this tendency for the risk to be higher at lower dose, we will take the risk to be 5.0 x 10-6 per year per WLM in what we will refer to as model A. This risk estimate is based entirely on exposures much [higher] than those that will be experienced by

Jan 1, 1981

By Oliver Bowles

GLASS razor blades, glass chairs, and marble window panes attest that creative genius was still active in 1935. Many less striking, though doubtless more important, developments are to be recorded for the nonmetallic mineral industries, and not the least of them is the establishment of an Industrial Minerals Division in the A.I.M.E. under the able leadership of Samuel H. Dolbear, Chairman. Thus the nonmetallics are rightly granted equal dignity with metals and fuels in the category of mineral industries. The brief review of progress that follows merely touches the fringe of important developments in this broad field.

Jan 1, 1936

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

By Frederick T. Fischer

INTRODUCTION Post-Lower Ordovician karstification on a continental scale produced a wide-spread paleoaquifer in the upper portion of the Knox Group of the Southeastern United States. The presence of economic zinc deposits in the Knox of Tennessee is considered to be a con- sequence of this paleoaquifer(1). During The New Jersey Zinc Company's initial exploration of the middle Tennessee region the known artesian nature of modern Knox water and its potentially adverse effect upon mining activities was a matter of concern. This concern intensified as a mining situation appeared imminent and a program of hydrologic investigation was begun in early 1969 and continued through August 1972. The preliminary findings of this work were reported at the AIME World Symposium on Mining and Metallurgy of Lead & Zinc in 1970(2). This paper presents additional data acquired during subsequent stages of the program and relates the hydrologic relationships to the overall geologic framework of the area. PHYSICAL GEOGRAPHY The Elmwood mine is 85km east of Nashville and 8km southeast of Carthage in Smith County, Tennessee (Figure 1). Its physiographic location is in the Central Basin of Tennessee, a basin resulting from erosional breaching across the Nashville Dome of the Mississippian strata which now form the bordering Highland Rims. Both the Central Basin and Highland Rims are divisions of the Interior Low- lands Province. Outcropping rock units of the Central Basin are predominantly Middle Ordovician limestones with scattered high hilltops capped by Devonian and Mississippian strata. One outlier

Jan 1, 1977

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977

By E. W. Johnson, M. L. Hill

The dijfusiuity D was determined at 25° to 780°C- from hyd?-ogen evolution rates. Anomalous evolution from air-melted iron was att~zbztted to residual hydrogen, which is interpreted as a hydrogen compound that decomposes at a strongly temperature-(Ieperzdent rate above 500°C. Above 200°C, D = 0.0014 cm2sec-1 exp (-3200 cal per g atom/RT). Below, 200°C the diffusivity is anomalously low and represented by D = 0.12 cm2sec-l exp (-7820 cal per g atom/RT). It is postulated that at low temperatures the hydrogen in the metal is "trapped" with an energy 4.8 kcaL per g atom below- that of the interstitial hydrogen. 1 HE purpose of the present experimental study was to determine the diffusivity of hydrogen in a-Fe over an extended temperature range. As certain anomalies were encountered, attempts were made to understand the anomalies themselves. This research was in progress both before and after a determination of the diffusivity of hydrogen in nicke1.l The latter system was found to exhibit none of the anomalies of hydrogen in iron, and its description was far simpler. The experiments on nickel also

Jan 1, 1961

By E. Allen Wendt

It is both a great pleasure and something of a challenge for me to have this opportunity to address a gathering encompassing such a wealth of expertise in the minerals field, It is particularly challenging because I have been asked to turn your attention from the relatively glamorous subjects of gold and money to the more mundane questions of our International commodity policy and the place of buffer stocks in that policy. However, these questions may be of more immediate importance for our economic interests at home and Abroad. I can testify that the problems affecting international commodity markets and the possibility of international action To resolve those problems are matters of real concern to Washington as well as to your industries,

Jan 1, 1978

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By Charles H. Grant

Communications in whatever we do, is one of the major problems we encounter. In an effort to provide a better understanding of the use of explosives, I am going to take a little different view of what explosives are, and how you might look at them as tools to fragment rock, and some of the problems encountered in doing so. First, let's take the explosive, and although there are many factors involved, I want you to consider these as being reduced to only two--shock strain imparted to the rock by the high early development of energy; and the other, the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc..

Jan 1, 1968

From depths of 400 - 600 m, coal is transported by a conveyor in a drift or a bulk winder in a shaft, whilst men and/or materials are transported by a slope hauler or a cage winder. Assessment of the effect of alternative combinations on the key cost factors - output, capital, labour cost and construction time - allows the optimum choice for particular circumstances, there being no uniform solution.

Jan 1, 1976

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By Deepak Malhotra, William F. Riggs, Edward C. Dowling

INTRODUCTION Mining companies are In the business of making an acceptable profit on their Investments, It became obvious in the recent recession that economic profitability/viability depends on being the lowest cost producer In order to compete on a global basis. The burden of achieving this objective falls on the mineral manager. He must strive to produce a salable product in an environmentally acceptable process while continuously Improving the profit margln.(1,2) Metal prices fluctuate on a regular basis. They directly Impact revenue and hence operating philosophy. The mineral engineer needs to develop an optimum operating strategy to meet his overall objectives, One would expect that, In the modem era of complex computer models, it would be easy to develop an economic model to maximize profits and/or cash flow. Discussions with mill managers Indicate that one mine/corporation's optimum operating strategy is not necessarily optimum for another. This paper approaches the problems from basics "Economics 101" and Illustrates the complexity of developing a universal model which can be applicable to all mines. Case examples are used to illustrate the need for better communication to avoid the basic economic fallacy “that optimization of segments leads to optimization of the whole system.” TECHNICAL MODELS Technical models are a prerequisite to the development of economic models because they provide the necessary Input data to these models, The flow of material from a mine through the sale of the finished product is shown In Figure 1. The ore Is mined and milled, and the concentrate can be stored for sale or smelted and refined In-house or at a toll facility. The finished product(s) are held In Inventory until sold either through existing contracts or in the spot market. [ ] Fairly reliable technical models have been developed for mining, milling and smelter operations. Mine plans are developed to provide a good Indication of the relationship between production and cut-off grade. It is easier to change surface mine plans than plans for underground mines. However, there are limits to maximum production that can be achieved with existing equipment. It Is possible that mine benches may not be developed to handle additional equipment, even If It was purchased to enhance production. More often than not, the cut-off grade Is lowered to Increase throughput goals.

Jan 1, 1993

By L. W. Page

PREVIOUS to the introduction of the motor vehicle the broken stone or macadam road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear. of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appre¬ciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled, as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 2, 1914

By Vincent Gianella

Barite deposits are of widespread occurrence in Nevada but there are few pro-ducing properties; most of the latter are in northern Nevada. The production of the state is small at present-in the neighborhood of 15,000 tons annually-but is steadily increasing. The barite occurs in veins and also as replacement deposits in lime-stone. The bulk of the production has come from the replacement deposits. It is thought that the barite was deposited from rising hot waters similar to-and probably contemporaneous with-those responsible for some of the metallic ores of the state. This paper discusses only the deposits in northern Nevada. THE commercial mining of barite did not begin in Nevada until 1916 but although the production has been small there has been a rapid increase in tonnage during the past several years. Barite is widely distributed in the state and production comes from at least nine of the seventeen counties. Apparently this is not generally known, as only two counties are mentioned in a recent publications dealing with barite. The increase in output is due largely to recently discovered barite deposits in northern Nevada. The principal production has come from the northern portions of Lander and Eureka counties; smaller amounts from Elko County. The discussion in this paper is confined largely to the deposits in these counties. Most of the producing area is tributary to the Western Pacific and Southern Pacific Railroads, whose tracks lie along the Humboldt River. Barite is known from other northern counties but so far the production has been small. The output has come entirely from veins and replacement deposits, the latter largely in sedimentary rocks. In general, the barite from veins is white; that from the replacement deposits usually is dark gray to black, although some is light gray or white. Most of the veins contain sulphides and many barite-bearing veins have been worked for their content of base or precious metals.

Jan 1, 1940

By Marlene Olivares Cruz

The particles that make up the deep-sea sediments have two main sources: 1) those that are created in situ from dissolved components and 2) those that are washed into the ocean in solid phases from the continents, atmosphere, space and interior of the Earth. Many particles as they sink through the water column reaches the seabed and are known as pelagic sediments with terrigenous, biogenic, authigenic, and cosmogenic components. Among the minerals found in the terrigenous fraction of pelagic sediments are quartz, clay minerals, feldspar, micas, ferromagnesians, and the biogenic fraction with remains of siliceous organisms, such as, radiolarian and diatoms. The chemical nature of marine sediments is controlled by the contribution of particulate matter derived from various sources with varying compositions for the fixing of elements during deposition and the compositional changes carried out within the sediments during diagenesis. In the last decade there have been several studies on the mineralogical composition of seabed sediments, suspended particulate materials and cores, together with paleontological and geochemical data are used for paleoclimatic and paleoenvironmental reconstructions, analyze changes in sea level, stratigraphic correlations and identify past and present sources of sediment and terrigenous input pathways and to describe the current ocean mass (Martins et al., 2001, Oliveira et al., 1998). There is also a scientific and economic interest in the authigenic fraction of pelagic sediments formed from other materials for polymetallic nodules. The study of sediments associated with polymetallic nodules helps to know the genesis, evolution and occurrence of these deposits (De Koven et al., 2003, Dubinin et al., 2008).

Jan 1, 2011

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do alto-forno (AF) está ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas (MP), especialmente, as do coque. As propriedades do coque são reflexos das propriedades dos carvões que lhe deram origem. Em termos de propriedades ligadas à natureza do carvão, a qualidade do coque é bastante influenciada pelo rank dos carvões, que compuseram sua mistura, ou seja, quantidades de macerais reativos e inertes, bem como suas propriedades coqueificantes, que é, exatamente, a habilidade inerente aos carvões aglutinantes de quando aquecido, amolecer, tornar-se plástico e solidificar em uma massa coerente. Neste contexto, o presente trabalho se propõe a evidenciar as mudanças no modelo de britagem de carvões da Gerdau Ouro Branco, bem como a operacionalização do padrão criado. Após a implantação, verificou-se a elevação de 1.8% em DI.

Aug 17, 2017

By J. T. Williams

The equilibria in the V-Zr alloy system were investigated by solidus temperature determinations, thermal analysis, dilatometry, electrical resistance measurements, microscopic examination, and X-ray diffraction analysis. There is a eutectic reaction at 1230°C between a compound, V2Zr, and a solid solution containing 10 pct V in ß zirconium. V2Zr decomposes at 1300°C into liquid and a solid solution containing about 10 pct Zr in vanadium. The eutectic composition is probably about 30 pct V. A eutectoid reaction between V2 Zr and a zirconium takes place at 777°C at a very high rate. The eutectoid composition is 5 wt pct V. The limit of solubility of zirconium in vanadium was estimated to be 5 pct at 600°C. No attempt was made to determine the liquidus for the system. THE recent availability of large quantities of high purity zirconium has stimulated the study of zirconium binary systems. The equilibrium diagram for the V-Zr system has received little attention, however. Wallbauml appears to have made the first report concerning the equilibria in these alloys. He reported the existence of a compound, V2Zr, having the MgZn2 ((214) type of structure with a, = 5.277 kX and c° = 8.647 kX. Anderson, Hayes, Roberson, and Kroll2 made a survey of some potentially useful zirconium binary alloys and found that zirconium probably dissolves a small amount of vanadium. They reported the probable existence of a compound between the two elements and suggested that the zirconium-rich solid solution undergoes a eutectic reaction with this compound. Pfeil," in a critical review of the existing information, estimated that the solubility of vanadium in zirconium is less than 4.7 pct and probably less than 1.8 pct. Rostoker and Yamamoto' proposed a partial diagram for the V-Zr system in a survey paper on vanadium binary alloys. Their diagram indicates the compound, V,Zr, a eutectic reaction at 1360°C, a peritectic reaction at 1740°C, and a limit of solubility of zirconium in vanadium of about 3 pct. They obtained no information on the equilibria in the zirconium-rich alloys. In view of the potential utility of the V-Zr alloys and the incomplete knowledge concerning the equilibria in the system, an attempt was made to establish the constitutional diagram. Preparation of the Alloys Raw Materials: The vanadium for making up these alloys came from the Electro Metallurgical Corp. Zirconium came from two sources. In the beginning of the investigation, sponge zirconium from the Bureau of Mines was used in making some of the alloys. Later, iodide metal made at the Westinghouse Atomic Power Development Laboratories became available. This material was used in the preparation of all the dilatometric and resistance specimens and about two-thirds of the solidus temperature specimens. A typical manufacturer's analysis of the vanadium is shown in Table I. No other analysis of the vanadium was made. The metal contained a dispersed second phase and did not have a sharp melting point. Typical results of spectrographic analysis of the Westinghouse zirconium are shown in Table 11. These data indicate a very high purity. The Bureau of Mines sponge metal was probably less pure but had good ductility. Melting: All of the alloys used in the investigation were made by melting pieces of vanadium and zirconium together in a dc electric arc furnace similar to those of Geach and Summers-Smith, craighead, Simmons, and Eastwood," and others. Melting was done in an atmosphere of helium scavenged of residual air by the preliminary melting of a separate charge of zirconium. Each ingot was turned over and melted at least three more times before removal from the furnace to aid in the attainment of homogeneity. Alloys prepared for use in the investigation are listed with the results of solidus determinations in Table III with the exception of the following compositions upon which no solidus determinations were made: 0.29, 0.54, 4.57, and 5.55 pct V. Analysis: The weight of each ingot made from iodide zirconium was within 0.1 g of the total weight of the initial charge, about 90 g. Since each component of each charge was weighed to the nearest 20 mg for amounts less than 10 g and to the nearest 0.1 g otherwise, the gross composition of an ingot could be calculated accurately. Chemical analysis for the vanadium content of several alloys agreed

Jan 1, 1956

By J. G. Trowell, D. T. Magee

"IntroductionMANITOBA'S first recoverable oil was from the California Standard Daly 15-18 well in Lsd. 15, Sec. 18, Twp. 10, Range 27, W.P.M., completed early in 1951. This well also gave the first indications of commercial production in the Williston basin, which is centred in North Dakota and extends into southeastern Saskatchewan and southwestern Manitoba. Subsequent drilling in the Manitoba portion of the basin has revealed the presence of oil in more or less commercial quantities at various points in an area approximately four townships in width and eleven townships in length.Although completions are becoming fairlly widespread in the area,, the greatest activity is in the Virden district, with the focal point in the Daly field, approximately eight miles west •of Virden. This paper will deal with the various techniques used in the Daly field, where •completion problems have •been unusually troublesome. Techniques evolved there have already been used with success at other points in southwestern Manitoba.Daly FieldGeneralTo date, all production has been from the Mississippian limestone, which is encountered •at depths ranging from 2,300 to 2,500 feet. Pay thickness is •of the order of 100 feet. Core analyses indicate average porosity .of about 9 per cent but permeabilities, for the most part, are extremely low."

Jan 1, 1953