Search Documents

By W. T. Weller

In Part I, a study of pressure build-up curves calculated for conditions under which both oil and gas flow led to the conclusion that the presence of a dispersed free gas phase in an oil reservoir must be taken into consideration to estimate accurately average reservoir pressure and permeability from build-up curves. Familiar methods based on the assumption of no free gas can be extended to the two-phase case by using total compressibility and mobility in place of single-fluid compressibility and mobility. These methods give correct values for average pressure and permeability when gas saturation is small. Errors become larger as the gas saturation increases. However, for the use to which the results will be put, the methods are satisfactory for reservoir engineering purposes. An improved method of calculating the performance of depletion-type reservoirs is presented in Part 2. Because the mathematical relationships describing simultaneous flow of oil and gas are quite involved. simplifying assumptions are made to provide means of obtaining approximate solutions of reasonable accuracy. One such approximate method now in use is the constant-GOR solution. It involves the assumption that at any instant, the ratio of total gas flow rate (both free and disolved) to oil flow rate is the same at all points in the reservoir. The approach is not applicable unless the free gar saturation in the reservoir is everywhere greater than the critical gas saturation. This paper presents a modification which, by avoiding the constant-GOR assumption, makes the method applicable to all reservoir conditions, and so far appears to be more accurate than the constant-GOR solution and to he comparable in required compuctation time. PART I— BUILD-UP CURVE ANALYSIS INTRODUCTION Pressure build-up characteristics of shut-in wells have been used for many years by engineers to evaluate average reservoir pressure, effective permeability thickness of the pay section, effectiveness of well completion (skin effect) and reservoir size. A number of methods of analysis have appeared from time to time."" Without exception, these methods are based on the assumption that the reservoir contains but one fluid of constant small compressibility and constant mobility. It has been suggesteda" hat these single-fluid methods may be applied to data from reservoirs containing both oil and gas by substitution of some effective total properties of the multiphase system in place of the corresponding single-phase properties. The present investigation was undertaken primarily to evaluate this approach. METHOD A number of theoretical build-up curves were calculated for conditions of two-phase flow, under the assumption of certain reservoir and fluid properties, and were analyzed by single-fluid methods with appropriate total compressibility and total mobility values for the corresponding single-fluid properties. Results of the analyses were compared with the assumed conditions. The theoretical build-up curves were completed by procedures similar to those of West, Garvin and Sheldon." Since these calculations require a considerable amount of computer time, an attempt was made to derive an approximate calculation method. The attempt was unsuccessful for calculating build-up curves, but the effort did result in a new approximate method of calculating the performance of solution gas drive reservoirs, which appears to be an improvement over the constant-GOR method" used previously (see Part 2). The West, Garvin and Sheldon calculations involved the following assumptions: (1) the reservoir is circular and completely bounded, with a completely penetrating well at its center; (2) the porous medium is uniform and iso-tropic, with a constant water saturation at all points; (3) gravity effects can be neglected; (4) compressibility of rock and water can be neglected; (5) the composition and equilibrium are constant for oil and gas; (6) the same pressure exists in both the oil phase and the gas phase; and (7) no afterproduction occurs, i.e., the well is shut in at the sand face for build-up. These assumptions make it possible to describe two-phase flow of oil and gas by the partial differential equations:

Jan 1, 1967

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By Robert M. Keeney, Jay Lonergan

The electric smelting of manganese ore and the production of ferro-manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 11/4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese orc in the electric furnace during the war and in 1920 are listed in Table 1. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferromanganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the price of ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 1, 1922

By Jay Lonergan, Robert M. Keeney

The electric smelting of manganese ore and the production of ferro-manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 11/4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese orc in the electric furnace during the war and in 1920 are listed in Table 1. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferromanganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the price of ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 1, 1922

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By C. Graeme-Barber, R. L. Bell, T. G. Langdon

An analysis is made of the formulas and ,methods used to estimate the contribution of grain boundary sliding to the overall strain of a polycrystal. The errors involved in the approximations and/or ,mistakes in earlier work are assessed quantitatively so as to make possible the critical use of previously published data. SINCE it has been found that, under conditions of very slow creep, the strain due to grain boundary sliding (?gb) may contribute as much as 80 pct of the total creep strain,1,2 it is obviously important to have reliable methods for estimating this grain boundary strain. In two recent papers Stevens3,4 has drawn attention to the pitfalls encountered in assessing ?gb. He criticizes 1) the assumptions made in the derivation of some of the formulas for ?gb, and 2) the indiscriminate averaging procedures used for obtaining the quantities substituted in these formulas. These and further criticisms of earlier work are mostly valid. Unfortunately the only formulas and procedures recommended are either impossible or very difficult to apply in practice. Furthermore no attempt is made to assess the errors involved by the earlier approximations or mistakes, and so it is not possible to make critical use of any of these early dab. The present article attempts to improve on these shortcomings by reference to empirical verification of easily applied formulas whose theoretical derivations involve some otherwise unjustifiable assumptions, and by a quantitative assessment of the errors in previous work. DEFINITIONS First it is necessary to define the terms and symbols to be used. The choice of symbols preferred here is a logical combination and extension of the v introduced by McLean5 and the u by Brunner and rant.' In Fig. 1 the two grains X and Y are displaced by the sliding vector AC. u is the component of sliding resolved along the stress axis, v is that measured perpendicular both to the stress axis and to the specimen surface, and w is that measured perpendicular to the stress axis but in the plane of the surface. Two angles define the orientation of the grain boundary: 8, between the stress axis and the surface trace of the boundary, and +, the internal angle on a longitudinal section cut perpendicular to the surface. In computing the strain resulting from the boundary displacement at all the in- dividual boundaries in a polycrystal the components u, v, or w are sometimes averaged along a longitudinal line (i.e., parallel to the stress axis), sometimes along a transverse line, and sometimes at randomly chosen boundaries. Averages obtained in these three ways are given subscripts 1, t, and r, respectively. Stevens rightly calls attention to the possibility of non-equiaxed grain shapes either at the start or at the end of deformation. In this article all values of numbers of grains per unit length will refer to measurements made before deformation. The subscripts 1 and t will be used for the number of grains per unit length obtained along longitudinal and transverse lines, r for that obtained by averaging along a number of randomly directed lines. FORMULAS FOR ?gb ?gt, as a Function of u. An obvious truth is that cgb can, in principle, be obtained by summation of all the v components at the boundaries intersected by a longitudinal line of known length I, viz.: where nl is the number of grains per unit length, parallel to the stress axis, in the unstrained specimen. There are assumptions in the analytic derivation of Eq. [I] due to Brunner and rant' but ~achinger' arrived at Eq. [la] by a rigorous method. Unfortunately the experimental procedure required by Eq. [ la] proves very difficult as boundary migration tends to obscure the points at which the longitudinal line meets the grain boundary and the errors on such measurements tend to be large, see Fig. 2. For example, on a specimen of Magnox AL 80 at a creep strain of 9.7 pct, 300 measurements of u obtained from the points of intersection of a longitudinal line with the grain boundaries gave ul = 8.95 ± 3.58 pm, or an error of ±40 pct, at the 95 pct confidence limit. These large errors due to migration may be avoided by measuring u from the separation of the segments

Jan 1, 1968

By Kurt A. M. Westerlund

The basic function of primary gas handling downstream non-ferrous pyro-metallurgical processes is cooling hot sticky gases to treatable temperature levels (e.g. entering ESP). That means managing efficient the critical gaseous components from a molten via a sticky to a solid phase. The article outlines the modem gas cooling methods combined with efficient heat recovery. Examples of the alternative use of recovered steam energy are outlined; as e.g. drying of concentrate and power generation. The heat transfer impact of the insulating dust is called fouling and circumstances causing fouling are described. Modem cooling surface design and cleaning techniques to keep fouling in reasonable limits are described. Leakage- and false air ingress into the gas handling lines often limits smelting capacity. The objective is generally to minimize the infiltration of air but it still takes place at open interfaces (e.g. at reactor hood, feed port). Leakage air at furnace roofs for example can be reduced to a minimum by adopting the pressure gas sealing used at present In-Bath-Lance furnaces. Modernization and optimization methods to de-bottleneck existing waste heat boiler gas cooling capacity by highly efficient surface cleaning systems and false air avoiding (e.g. bundle roof boxes, dust discharge) are detailed described.

Jan 1, 1999

By D. W. Fuerstenau, P. C. Kapur

A new method is proposed for measuring the grindability of solids and the energy efficiency of grinding mills. The method is based on a similarity law of fracture mechanics for elastic materials in conjunction with the self- preserving character of the size distributions formed when feed particles are comminuted individually in compression. The single-particle grindability index reflects more closely the inherent resistance of a solid to size reduction than the grindability indices currently in vogue. The performance of grinding mills is evaluated in comparison with the single-particle breakage mode, which has the highest energy utilization or efficiency of all mechanical grinding routes. For a given set of stipulations, the performance index of the commonly used ball mill when grinding dolomite is found m he only 21%. compared to 44% for the high-pressure roll mill, a newly-invented energy-efficient mill. The difference is also reflected in the energy consumed per unit mass offines produced when closed-loop grinding circuits are simulated, which shows that the high-pressure roll mill circuit is invariably more energy-efficient than the ball mill circuit, provided the energy input per pass through the mill does not exceed a prescribed limit. Theoretical upper bounds on the yield of the ground product in a desired size range and lower bounds on the energy investment are calculated from the single-particle breakage mode which has, apart from the highest energy utilization efficiency, a minimum dispersion in size of the comminuted particles. Data on theoretical hounds for seven minerals/ores are presented. It is argued that it is unlikely that a grinding mill can be designed and a comminution circuit constructed whose performance exceeds these bench-mark values.

Jan 1, 1995

By C. Garcia, C. L. Lin

Characterization and analysis of multiphase particles and/or particulate systems (such as the packed particle bed) are of great technological importance for mineral processing applications. In general the performance of these applications depends on the statistical characteristics of particle microstructures, such as composition distribution, surface exposure of mineral grains, pore network structure, etc. For continued technological progress in the field of multiphase particulate processes, the need for quantitative spatial analysis of multiphase particles in three dimensions has increased sign6cantly. Such quantitative information must be accurate enough that the measured values can be used as parameters for simulation models, process design procedures, and control strategies. Modern 3D image-acquisition techniques, such as X-ray microtomography (XMT), offer a unique imaging capability that can produce high-resolution (a few micrometers) three-dimensional images of the internal structure of multiphase particulate samples. These three-dimensional image data present new challenges for image analysis, image processing, and visualization. Furthermore, important issues should focus on how to use the 3D information and derive new insights into the improvement, design, and operation of mineral processing processes. In this paper, utilization of XMT for characterization and analysis of leaching process involving multiphase particulate system is discussed.

Jan 1, 2005

By H. Kenyon Burch

PaQe Introduction.............................................................. 708 Plant Sites................................................................ 709 Type of Construction...................................................... 710 Mine Plant............................................................... 710 Dual Arrangement.................................................... 711 Underground Haulage............................................. 711 Tipples........................................................... 712 Underground Pockets............................................. 712 Automatic Measuring and Loading Devices......................... 712 Shafts ............................................................. 716 Ore and Spillage Skips............................................ 716 Automatic Hoists................................................. 716 Man Elevator..................................................... 717 Crushing Plant....................................................... 718 Storage Bin........................................................... 720 Sampling Plant....................................................... 720 Motors and Other Equipment.......................................... 721 Compressor Equipment................................................ 721 Concentrator............................................................. 722 600-Ton Test Mill..................................................... 722 The 15,OO0-Ton Concentrator...................................... 726 Grinding Section.................................................. 726 Floor Arrangement........................................... 726 Marcy Ball Mills............................................. 729 Performance of Crushing Machines............................ 730 Flotation Section.................................................. 780 . Flow-Sheet with Callow Flotation Cells....................... 731 Flow-Sheet with the Inspiration Flotation hfachines............. 731 Flotation Air Supply.......................................... 733 Concentrates Filter Plant.......................................... 733 Drag Classifiers................................................... 733 Tailing Settling System........................................... 735 200-Ft. Dorr Thickener ...................................... 736 General Equipment and Supplies.......................................... 737 Water Supply......................................................... 737 Power Supply......................................................... 737 Transformer Stations.................................................. 738 Shops and Railroad Facilities.......................................... 739 Conclusion................................................................ 740

Jan 1, 1917

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By Cristián Araya L.

A dynamic agglomeration, heap leaching, solvent extraction and electrowinning software, called NICO, has been developed in order to either design or simulate copper ore recovery plants. NICO contains a library of routines, each representing a unit operation or piece of equipment, which are assembled like a meccano to match almost any wet plant configuration. Routines include agglomeration or curing either in drums or belts, belt conveyors, heap stacking and reclaiming, heap leaching of oxide, sulfide or mixed copper ores, heap irrigation, drainage, ponds, mixer-settlers, filters, columns, coalescers, tanks, electrowinning cells, pumps, and all connections and related piping. All models are semi- phenomenological, i.e., they include all physical-chemical, mass, thermal, transport equations, which are required to represent as closely as possible the equipment or unit operation. However, operating experience has been incorporated into the model in order to make it simpler, faster and reliable. This experience has been tested in several plants in Chile since 1992. Site meteorological data is simulated also; in this way the model is responsive to weather conditions (temperature, solar radiation, ambient humidity, atmospheric pressure, wind velocity, etc). NICO has been used recently for design and optimization studies in copper plants in Chile like Radomiro Tomic, Collahuasi and Zaldivar. A user-friendly interface allows fast and comprehensive simulations. The entire plant is shown in a single graphic screen, so the user can see all the relevant information, and soft-keys are provided in order to change parameters on-line and watch their effect in final copper production in cathodes. Model also calculates and reports operating parameters, as well as estimated investments and operating costs.

Jan 1, 1999

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By James A. Clem

Approximately 2000 years ago, the Lord admonished the scribes (lawyers) and pharisees (religious leaders of that time) that they had paid the tithe but had omitted the weightier matters of law, judgment, mercy, and faith. (Matt. 23:23) I want to talk about "The Weightier Matters of Law." In a situation where big government is trying to have an effect on even small details of a work activity, otherwise simple situations become complex. Regulations are written to such detail that constant compliance with strict interpretations can be a nightmare-not to mention off the target of the intended purpose for the regulation. One soon recognizes the onerous characteristics of federal statutes. Another admonition the Lord gave those lawyers and pharisees back then was that they tended to strain at a gnat and swallow a camel! He meant that the pharisees were given to devoting themselves to the strict interpretation of law by writing hundreds of subrules or interpretation to law. In doing so they eventually lost sight of the original purpose of the law. I think they were being told, keep the law-but don't neglect to humanize it Keep it simple Recognize the purpose of why the law. "Mix in" a common sense approach. Someone once said, "Common sense is instinct -enough of it is genius." Today, as 2000 years ago, we need more "genius" displayed by legislators in considering the weightier matters of law. First of all true legislature genius calls for a declarative statement about the purpose of the statute and a fair, objective analysis of the ground rules by which it will be implemented. In the Health & Safety Act of 1969, the "findings and purpose" as set forth in Section 2 do define its purpose. I believe most of us affected can be in accord with the reasons advanced for the legislation. However, beyond those well-intentioned few paragraphs, we very quickly run into trouble. Congress complicated the simplicity of the statement of purpose by mandating government intervention into areas that cannot be effectively legislated, nor even should be legislated. The Act provided for broad gaged regulation which is unnecessary, inappropriate, and tremendously costly. Frankly, it detracts from a constructive, cooperative effort by the parties involved. These are strong negatives which characterize inappropriate legislation. Appropriate legislation and subsequent regulation, which is realistically conceived and practically enforced must be born of an honest desire for improvement, based on a working knowledge of common problems which are thoughtfully analyzed. Then the legislation must be written in clear concise language so that there can be little or no doubt as to its literal meaning and intent. To be practically enforced, it must be understood by all who will enforce it and by all who are subject to it. That is to say, an effective law or standard cannot be fixed or inflexible so that it cannot be tempered in human judgment. There must be an elasticity in the statute to provide for consideration of all of the relevant facts of a given situation. Such elasticity makes the compliance effort as meaningful as it can be for the time and dollars invested. Meaningful compliance requires room for common sense. Today, we in business along with our associates in government and labor, urgently need to pause, and assess our current situation. The problems arising from the 1969 Act have been intensified through the Mine Safety & Health Act of 1977. After reading the "findings and purpose" of this legislation, and by process of elimination, we should all clearly see what is and is not the purpose of the Act. 1) It is not to turn the management of private industry over to government. 2) It is not to impair the efficient operation of business. 3) It is not to reduce productivity and profits. 4) It is not to reduce national unemployment. 5) It is not to perpetuate the bureaucracy. 6) It is not to increase the tax burden on an already overburdened people. 7) It is not to increase our balance of payments deficit. 9) It is not to replace management/labor relations in working together to solve problems.

Jan 1, 1981

By P. Somasundaran, D. W. Fuerstenau

The length of the collector is found to influence the flotation of the mineral even at incipient conditions, which are below the concentration at which interaction at the solid-liquid interface begins to take place to form hemi-micelles. To study this dependence, concentration for incipient flotation of quartz was determined as a function of pH with collectors of various chain lengths. The observed effect of chain length on flotation is ascribed to that of collector adsorbed on the bubble surface. In previous studies, it was shown that at low concentrations the alkyl collector ions adsorb at the solid-liquid interface as individuals.''2 At higher concentrations, the collector ions adsorbed at the solid-liquid interface associate with each other to form two-dimensional aggregates called hemi-micelles. Above the hemi-micelle concentration, the length of the hydrocarbon chain is extremely important since the hydrocarbons are in effect removed from water during the association, making the energetic conditions more favorable for adsorption at the interface. Because of this enhanced adsorption, one observes a very rapid increase in flotation associated with the hemi-micelle formation at the solid-liquid interface. However, a dependence of flotation on the chain length at concentrations below that required for hemi-micelle association was also observed,' and this cannot be explained by the above mechanism which postulated hydrocarbon chain interactions only at the solid-liquid interface. This prompted an investigation into other possible reactions of the hydrocarbon chains and an examination of the conditions at the bubble surface involved in the flotation system and how these observations might explain the reactions at the solid-gas interface which cause the particle-bubble attachment required for flotation. To obtain more information on chain length effects, flotation, under incipient conditions, was tested by vacuum flotation techniques. The collector-concen-tration-pH relationships for flotation of quartz with alkyl ammonium acetate collectors was delineated by observing the pH at which quartz particles begin to float to the liquid surface. By investigating flotation as a function of pH, it was also possible to study the effect of neutral molecules on incipient flotation conditions, since the aminium ions hydrolyze to amine molecules at higher pH values. EXPERIMENTAL WORK Brazilian quartz specimens were crushed and sized, and the 270 x 400 mesh fraction was used for flotation studies. The samples were leached with concentrated hydrochloric acid until no coloration of the acid occurred. The leached material was washed free of chloride ions and stored in distilled water. The vacuum flotation technique developed by Schuhmann and prakash3 was used to determine the critical pH-concentration curves. This method, which can be used to delineate conditions for incipient flotation, is fairly simple and rapid. About 0.5 gm of 270 x 400 mesh quartz was placed in a 100 ml graduated cylinder which was then filled to the 100 ml mark with the collector solution made from high-purity alkyl ammonium acetate salts. The water used for the test was conductivity water saturated with air that had been passed through a cleansing train consisting of Drierite, Ascarite, a water wash bottle, and a trap. After the pH was adjusted, the cylinder was then conditioned for thirty minutes. In the tests where an acid pH was desired, sufficient acid was added before the collector solution to avoid any effect due to slow desorption of collector from the quartz surface. After conditioning, vacuum was applied to the system and the flotation or nonflotation of the quartz was noted. The pH at which the quartz particles began to float to the liquid-gas interface was taken as the critical PH. Critical pH curves were thus determined for different concentrations of the various collectors. Hallimond tube flotation data were taken from the authors' previous publication1 for correlation with that from the vacuum flotation. RESULTS AND DISCUSSION The results of vacuum flotation studies for determining critical pH-concentration curves, i.e., curves which delineate conditions for incipient flotation, are shown in Fig. I. In generaI, all the curves exhibit an upper and lower pH limit between which flotation will

Jan 1, 1969

By I. I. Inculet, M. A. Bergougnou, J. D. Brown, R. M. Quigley, D. K. Faurschou

"Coal from Hat Creek, B. C., has been successfully beneficiated to remove ash while retaining calorific value by a dry electrostatic separation process using a fluidized bed for triboelectrification. Two samples of Hat Creek coal used in the beneficiation experiments have been characterized particularly with respect to their mineral and clay content. The calorific value recovery exceeds the simple dry coal recovery because of the heat lost in altering the clay minerals of the ash fraction during burning. Recoveries and ash contents of the beneficiated coal are comparable to recoveries by water washing, but the dry process avoids the potential water pollution problems.IntroductionProposals have been made which suggest an interim Canadian coal production target for the end of the century which will require a four- to fivefold increase over the 1977 production. This implies a nominal annual growth rate of about 6070 to achieve a production rate of 115 to 140 million tonnes/year. Whether or not this target is realistic, it is becoming increasingly evident that coal must be utilized more fully on a world-wide basis. The crisis in Iran has provided the latest stimulus to renewed interest in Canadian coals for domestic use and export.The emerging new era of coal utilization for fuel and chemical feedstock will not, however, generally tolerate the level of coal technology which prevailed prior to the availability of abundant cheap oil and natural gas. Economic, environmental and resource management considerations will necessitate, for example, the use of improved methods of beneficiating coal. Continued development and application of conventional processes, principally aqueous, involving heavy media and cyclones will solve many of the problems. However, less conventional processes may be preferable or necessary in certain applications."

Jan 1, 1980

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude petroleum from producing, fields in the United States and the Western Hemisphere, and has published a series of reports on these fields, including oil fields of Oklahoma2. Acknowledgements Thanks are due to R. R. Brandenthaler and Peter Grandone, of the Petroleum Experiment Station of the Bureau of Mines, at Bartlesville, Oklahoma, who reviewed the manuscript and contributed valuable suggestions. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1927

By J. Lohrenz, C. R. Clark, B. G. Bray

Procedures to calculate the viscosities of in situ reservoir gases and liquids from their composition have been developed and evaluated. Given a composition expressed in methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide together with the molecular weight and specific gravity of the heptanes-plus fraction, the procedures are capable of calculating the viscosity of the gas or liquid at the desired temperature and pressure. The procedure for reservoir liquids was developed using the residual viscosity concept and the theory of corresponding states, and was evaluated by comparing experimental and calculated results for 260 different reservoir oils ranging from black to highly volatile. The average absolute deviation was 16 per cent. This is the first known procedure for calculating the viscosity of reservoir liquids from their compositions as normally available, i.e., including the heptanes-plus fraction. The procedure for reservoir gases uses a sequence of previously published correlations. Evaluation of the procedure was accomplished by comparison of 300 calculated and experimental viscosities for high-pressure gar mixtures in the literature. The average absolute deviation was 4 per cent. The calculations are useful for (I) determining viscosities in compositional material balance computations and (2) predicting the viscosity decrease which occurs when gases, LPG, or carbon dioxide dissolve in reservoir oils. INTRODUCTION Methods to predict viscosities of reservoir fluids from the normally available field-measured variables have been presented. Beal,1 Standing,2 and Chew and Connally3 orrelated oil viscosities with temperature, pressure, oil gravity and gas-oil ratio. Carr, Kobayashi, and Burrows4 and Katz et al.5 have presented correlations for reservoir gas viscosities as a function of temperature, pressure and gas gravity. Lie all intensive physical properties, viscosity is completely described by the following function: Eq. 1 simply states that viscosity is a function of pressure, temperature and composition. These previous correlations1- hay be viewed as modifications of Eq. 1, wherein one assumes more simple functions may be used. The assumptions are practical, because the composition is frequently not known. Further, the assumptions are sufficiently valid so that these correlations are frequently used for reservoir engineering computations. In compositional material balance"' computations, the compositions of the reservoir gases and oils are known. The calculation of the viscosities of these fluids using this composition information is required for a true and complete compositional material balance. For reservoir gases, Carr, Kobayashi and Burrows4 have presented a suitable compositional correlation. For reservoir oils, no correlation is available, and data from reservoir fluid analyses have been used7-9 for compositional material balance calculations.* From a theoretical point of view, this is entirely invalid. The reservoir fluid analysis, whether flash, differential, or other process, does not duplicate the compositions which occur during the actual reservoir depletion process, therefore the viscosities measured during reservoir fluid analysis are not those which occur in the reservoir. From a practical point of view, the "error" of using viscosities from reservoir fluid analysis is of varying and unknown significance. One can say qualitatively that the error is greatest where compositional effects are greatest, i.e., for volatile oil and gas condensate reservoirs and pressure maintenance operations. The first requirement to obtain a quantitative estimate of the significance of the error is to develop a reliable compositional correlation for the viscmities of reservoir oils. No such correlation has been available. Consistent with this requirement, the objective of this study was to develop a procedure to predict the viscosity of reservoir fluids from their compositions. Normally, the compositions of reservoir fluids are available expressed as mole fractions of hydrogen sulfide, nitrogen, carbon dioxide and the hydrocarbons methane through the heptane-plus fraction, with the average molecular weight and specific gravity of the latter. The final correlation was to use the composition in this form. While the more challenging objective of the study was the development of a correlation for the viscosities of reservoir oils, the viscosities of reservoir gases were also studied. The end result of the study was a procedure to calculate the viscosities of reservoir gases and liquids suitable

Jan 1, 1965

By Jacques H. Nantel, James F. Archibald

"Frozen tailings material may be required, in the future, to perform the support functions of underground backfill in mines located in zones of permafrost, notably in the high Arctic. To date, no knowledge of physical support parameters of such materials has been obtained in Canada due to the limited mining activity in permafrost regions. It is therefore judged essential that the important physical and mechanical properties relating to frozen tailings material be assessed.Innovative mining methods will be required to cope with the harsh environmental conditions that exist at mining sites in the Canadian Arctic. A preliminary laboratory study, in the absence of field trials at limited Arctic mining sites, has been completed in which the physical and mechanical properties of several types of representative mill tailings mixtures have been investigated. A variety of tests, to determine frozen slurry and pelletized tailings strength properties, moduli of compression, optimum water contents, deformation characteristics and the like, have been conducted.The results of this study will be used to establish guidelines for the suitability of tailings use in such northern mining environments. IntroductionFrozen tailings material has never been used to backfill underground openings in Canadian mines. At present only one Canadian mine, the Polaris Mine situated on Little Cornwallis Island, is investigating the use of frozen backfill. However, the Canadian North covers a large territory and potentially contains a large number of mineral deposits. The understanding of concepts related to mining activities in sub-zero frozen ground is therefore important.The implications of using frozen tailings as underground backfill material are far reaching both from the point of view of mine stability and disposal of tailings in the arctic regions.The strength of frozen materials (soil, backfill, etc.) may take on different meaning depending on the engineering situation. Both the concepts of rupture and excessive deformation need to be considered.The functions usually required to be performed by the backfill material in underground mines may be summarized asfollows:a) working floors; such as in cut-and-fill stopesb) stope wall support; for cut-and-fill and delayed fill stope~c) self-support when backfill is exposed on one face; during pillar recovery phases.For fill functions such as working floors, the short-term response of the frozen fill is the dominant concern. For the other fill functions, the long-term deformation response of the frozen fill, or creep, is of interest."

Jan 1, 1986

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993