Search Documents

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By D H. Bell

Slab-buckle failures in coal sequences involve thin slab deformation in strata dipping parallel to the footwall, and are a consequence of both unloading and the weak nature of the thinly bedded rock mass. Methods of modelling and predicting such occurrences include: +        a conceptual model using a base friction table, +        a mathematical model using the Euler solution for column and beam bending (after Goodman, 1980), and +        computer analysis techniques such as UDEC (Universal Distinct Element Code after Cundall and Hart, 1993).   Slab-buckle failures have the potential to seriously disrupt production because of their volume and rapidity, and to endanger both equipment and personnel working on the pit floor.   In July 2004 a large slab-buckle failure occurred overnight after a new batter and bench had been formed at the Malvern Hills Opencast Mine in inland Canterbury. This involved the entire length of the pit (85m along strike) when a 2m thick intact slab with a total volume of ~3500m3 translated down dip 6.2m on the base of a thin coal seam to form a pronounced buckle at the toe. The coal measures consist of finely laminated mudrocks with multiple coal seams of varying thickness dipping ~45¦ to the southeast, and the opencast mine had been designed with footwall batters formed parallel to bedding with a vertical bench separation of 15m.   Back analysis of the Malvern Hills failure was necessary to investigate the controls on footwall instability, and for future mine design. An engineering geological model was created and samples of the slab material and failure surface were collected and tested to establish the required parameters for use in the Euler solution for column and beam bending. Back analysis using the Euler solution provided unrealistic results that overestimated the overall length of a stable slope by more than 10 times.   No further large scale slab-buckle failures have developed at the mine site, in part because of the slow rate of coal extraction, but precautionary drainage of the footwall slopes has been undertaken to improve overall batter stability. The location of the slab-buckle failure on a critically positioned pre-sheared thin coal seam with full hydrostatic head is considered the most probable cause of the July 2004 failure, rather than inherent instability of the generic bench and batter arrangement adopted. The use of a precedent-based engineering geology approach to future mine design is considered the most appropriate solution in the circumstances.

Jan 1, 2007

By E ¦iftti, A Koenig

Natural sphalerite associated with copper, silver, lead-zinc, tin and tungsten deposits from various world-famous mineral deposits have been studied by cathodoluminescence (CL), laser ablasion inductively coupled plasma mass spectrometry (LA-ICP-MS), electron probe microanalysis (EPMA) and electron paramagnetic resonance (EPR) to determine the relationship between trace element type and content and the CL properties of sphalerite. In general, sphalerite produces a spectrum of CL colour under electron bombardment that includes deep blue, turquoise, lime green, yellow-orange, orange-red and dull dark red depending on the type and concentration of trace quantities of activator ions. Sphalerite from most deposits shows a bright yellow-orange CL colour with lmax centred at 585 nm due to Mn2+ ion, and the intensity of CL is strongly dependent primarily on Fe2+ concentration. The blue emission band with lmax centred at 470 - 490 nm correlates with Ga and Ag at the Tsumeb, Horn Silver, Balmat and Kankoy mines. Colloform sphalerite from older well-known European lead-zinc deposits and late Cretaceous Kuroko-type VMS deposits of Turkey shows intense yellowish CL colour and their CL spectra are characterised by extremely broad emission bands ranging from 450 to 750 nm. These samples are characterised by low Mn (<10 ppm) and Ag (<1 ppm), and they are enriched in Tl (1 - 30 ppm) and Pb (80 - 1500 ppm). Strong green CL is produced by sphalerite from the Balmat-Edwards district. Amber, lime-green and red-orange sphalerite produced weak orange-red CL at room temperatures, with several emission bands centred at 490, 580, 630, 680, 745, with lmax at 630 nm being the strongest. These emission bands are well correlated with trace quantities of Sn, In, Cu and Mn activators. Sphalerite from the famous Ogdensburg and Franklin mines exhibited brilliant deep blue and orange CL colours and the blue CL may be related to Se. Cathodoluminescence behaviour of sphalerite serves to characterise ore types and help detect technologically important trace elements.

Jan 1, 2008

By Todd Hamilton

For mine closure, the prospect of treating mine drainage in near-perpetuity can be onerous – especially when flow rates are high. One closure option is to construct tunnel plugs within the adits to flood the mine and reduce discharge volumes. Flooding reduces oxygen access within the mine and hence ARD potential. It also reduces hydraulic gradients such that uncontaminated groundwater is not drawn toward open, acid-generating areas of the mine/orebody. Evaluation of the technical and economic feasibility of permanently sealing mine tunnels necessitates detailed hydrogeological and geotechnical investigations. The capital costs associated with tunnel plugs may be relatively high, and there are ongoing maintenance requirements, risk of significant leakage and even risk of catastrophic failure if improperly designed or constructed. In this sense, the paper point put the means available for assessing the liabilities associated with adits at project start up, and the options available for closure of existing adits to reduce long-term environmental liabilities.

Sep 12, 2005

Five types of mineral resource were known in the sedimentary cover of the oceans and seas floors prior to the 1980's :1) hydrocarbon fields including some very large zones of oil and gas accumulation; 2) "Red Sea" type thermal oozes with increased concentrations of noble metals; 3) ferromanganese nodules; 4) concentrations of metallic sulphides ("Black Smokers"); and 5) cobalt-bearing ferromanganese crusts on the summits and slopes of seamounts. Since then, the so called "White Smokers", containing sulphides of copper and zinc, have been discovered. The ore horizons (manganese, copper, nickel and other metals) of the sedimentary cover of deep-sea basins comprise a sixth type of mineral resource in the oceans. These horizons have not only a theoretical, but also a principal economic significance

Jan 1, 1995

By Henry N. McCarl

[The Construction Materials section contains the following Chapters: Aggregates Cement and Cement Raw Materials Crushed Stone Dimension and Cut Stone Lightweight Aggregates Gypsum and Anhydrite Sand and Gravel Insulating Materials-Thermal and Sound Slag Roofing Granules] Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in portland cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the" world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggregate materials. The per-ton value of mineral aggregate materials at the production plant in 1980 and 1981 varied from $2 to $5 for most sand and gravel and crushed stone, $3 to $6 for air-cooled slag, $7 to $20 for expanded slag and expanded clay or shale aggregate, to as much as $165 to $320 for expanded perlite or vermiculite. The expanded lightweight aggregates have been dramatically affected by increasing fuel costs. It is ironic that the specialized aggregates used as insulating materials to conserve energy cost so much more to produce due to the high proportion of energy consumed in their production. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Lightweight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks, there will also be some coverage of sources, mining and production, especially in those cases where they are not discussed in the Commodity section of this book.

Jan 1, 1983

By Thomas CG, Armstrong GJ, Lynch KS

A small glass walled pot grate has been used to simulate drying of iron ore pellets in a travelling grate plant. This equipment has enabled the effect of decreasing grind and de- creasing pellet bulk density on plant production to be quantitatively predicted. These predic- tions are compared with plant experience. The use of the laboratory simulator in comparing the effect of various additives on plant production is also described and substantial improvements in both the goethite and free-water drying periods are predicted.

Jan 1, 1972

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

By William F. Butler, Mo-Hung Che

DEVELOPMENT OF MONEY AND MONEY STANDARDS This chapter is concerned with the rise, and then the decline and fall, of gold and silver as monetary metals. As a first step in tracing the history of this process, it is necessary to consider the nature of money, and the manner in which different forms of money have developed over the centuries. The origins of money go back into deepest antiquity. Once men ceased to be pure nomads and entered into even a rudimentary form of society such as clans or tribes, money had to be invented The first step was barter as farmers or hunters swapped their surplus products for things produced by artisans such as shoes, clothing, and simple tools. But such barter trading is inconvenient even in primative societies It is difficult to match up buyer and seller at any point in time There are problems in arriving at viable and acceptable terms of exchange. The accumulation of savings-wealth-is complicated. No one can be sure that a pile of furs, or wheat, or certainly fish or game can be used in the future to trade for other goods or services. So even prehistoric man saw the need for money. There was a need first for something to serve as a medium of exchange This was an essential first step in the process of specialization-or the division of labor. A farmer, a hunter, or a shoemaker could only devote his full efforts to his trade if he could be sure that he could exchange his surplus production for the other things he needed for existence. This required a medium of exchange-a form of money which would be broadly acceptable. Money was needed for two other reasons Some system of market prices was essential to facilitate the exchange of goods and services. This required some form of common denominator-some standard of value-to govern the exchange process. And there was also need for something to serve as a store of value, a place to put any excess production (savings) with the assurance that it can be used in the future to acquire a general range of goods and services. As a result, money, in one form or another, developed at a very early state in civilization. Yet the centuries have been marked by a search for a form of money which will possess in full measure all of the attributes in money-a reliable and universally acceptable medium of exchange, standard of value, and store of value. -A wide variety of things have been used as money at one time or another: shells, beads, stones, feather, metals, and even the teeth of sharks and dogs. Some of these things were obviously of little or no practical value. They were used because people had confidence in their continued acceptance as a medium of exchange. As the world evolved and as trading ex-

Jan 1, 1976

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

The Prospect to Pipehead Tunnel is a component of the Sydney Water Board's multi-million dollar Drinking Water Quality Program to improve the quality of Sydney's potable water supply to meet revised national health guidelines. The tunnel project involves the construction of seven kilometres of 3.9 metre diameter machine bored tunnel which is to be lined with a three-metre diameter steel liner. The paper describes the fully integrated planning and design approach and management technique used to enable this major project to proceed to meet the requirements of a tight construction program.

Jan 1, 1993

By E. J. Rapperport, J. P. Pemsler

The thermodynamic activities of zinc in six solid solution Cu-Zn alloys ranging from 5 to 35 at. pct Zn were determined experimentally in the temperature range 400° to 600°C. This low temperature investigation was canducted in order to evaluate techniques developed to utilize the inherently high sensitivity of atomic absorption flocesses in the measurement of thermodynamic activities. Analytical expressions ,for the activity and actizlity coeflcient are given for the six alloys in the temperature ranges investigated. RELATIVELY few experimental methods are available for investigation of thermodynamic activities of alloys, especially in the solid state. The techniques most frequently used have been the electrochemical potential and the effusion methods, both of which have severe limitations in many instances. It is therefore desirable to expand the ability to perform such measurements in order to obtain new information as well as to provide an additional independent verification capability. In this work, we present a significant improvement in the spectrophotometric method for sensing small vapor pressures in static absorption cells. Similar techniques have been used previously;1"5 however, applications had been limited to relatively high pressures, often greater than 1 torr. Prior investigators have, for the most part, used broad spectral sources such as xenon or mercury lamps, and high intensity arcs. Hollow cathode sources were first suggested in 1956 6 and were used soon afterwards.4'5 These sources offer significant improvements in sensitivity and freedom from interfering spectral lines.'-' EXPERIMENTAL High purity zinc was obtained from Cominco Products, Inc., and copper from American Smelting and Refining Co. Both elements were of 99.999 pct purity. Copper-zinc alloys were vacuum melted in a high fired carbon crucible with each alloy pulled from the melt as a 4 -in. diam bar. The bars were swaged to -1/4 in. rods and vacuum annealed for 160 hr at 800° + 1°C. Samples for gross chemical analysis were taken at intervals along the length of the rods to ascertain the axial zinc gradient. Electron microprobe analysis of homogenized specimens indicated that the alloys had uniform compositions over their cross sections on a macro (200 p) and micro (1 u) scale to better than *1 pct (20) of the gross composition. This tolerance was determined by counting statistics, rather than assured composition fluctuations. All SiO 2 windows were high-ultraviolet-transmission grade to minimize intensity losses. Silica absorption cells were scrupulously cleaned consecutively in organic solvents, dilute HF, and distilled water before use. The empty cells were then flamed while under a dynamic vacuum, cooled, and removed to an argon-filled glove bag. Alloy pieces were cut and filed in the glove bag to produce fresh surfaces, and then loaded into the cells. The loaded cells were temporarily sealed, removed from the glove bag, reevacuated to 10-5 torr or better, and permanently sealed. The instrument used is schematically shown in Fig. 1. The spectral emission from a commercially made hollow cathode lamp (A) of a selected element is focused through an absorption cell (B) inside a well-controlled furnace (C). The intensity of the transmitted beam is measured using the spectrometer* (D) 'Techtron model AA4 atomic absorption spectrometer. which contains a grating (E) that disperses the light prior to impingement on the photomultiplier (F). The monochromator grating is adjusted so that only the wavelength of interest is measured. The power supply delivered an interrupted voltage to the lamp, causing a chopped radiation output to be transmitted. The detector read only the intermittent component of radiation incident upon it, so that all continuous noise signals (furnace radiation, and so forth) were eliminated. Three recording thermocouples contained in the muffle furnace were positioned along the length of the absorption cell: one at each end and one at the center. An effort was made to keep the ends of the cell several degrees hotter than the center to avoid window condensate. Appropriate thermal corrections were then necessary to relate cell pressure to radiation attenuation. Water-cooled heat shields, as shown in Fig. 1, were found to aid signal stability by protecting the hollow cathode and the photomultiplier from furnace radiation. The furnace had a 2-in. diam muffle, Kan-thal wound, with SiO 2 windows at its ends to minimize convective effects. The hollow cathode radiation was masked and focused to form a conic beam that was a maximum of { in. diam within the furnace. Thus, the 1.5 in. diam absorption cell easily contained the entire beam. The furnace was mounted on ball-bearing slides with positive positioning detents. This arrangement allowed the removal of the entire furnace assembly from the radiation path, position [I], Fig. 1, so that frequent sampling of the unattenuated beam intensity could be obtained. In all cases the beam intensity was kept constant to 0.1 pct as judged by readings taken immediately before and immediately after data collection. Only data for absorptions of less than 80 pct were utilized, as systematic deviations from linearity were found for greater absorptions.

Jan 1, 1970

By Abell RS, Wyborn D, Solomon M, Stuart-Smith PG, Henderson GAM

The two major massive sulphide deposits in the Silurian rocks of southern NSW, Captains Flat and Woodlawn, differ from classical Kuroko deposits in several ways, e.g. they lie on the flanks of felsic volcanic piles in volcano-sedimentary marine sequences, are relatively thin and large compared to individual Kuroko deposits, show prominent banding in lead-zinc ore, and contain arsenopyrite. Qualified stuctural and stratigraphic correlations of the various fault-bounded remnant Silurian sequences that host these deposits provide the basis for a new interpretation of the regional geological setting that also differs from that of the Kuroko deposits (Ohmoto, Tanimura, Date, Takahashi, 1983), and sheds further light on the distribution of volcanogenic massive sulphide deposits in the Silurian rocks of NSW.

Jan 1, 1987

By C. A. Heiland

Measurements of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for comprehensive engineering information on the subject. The working principles of a number of gravimeters will be illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as elementary form as possible. A description of calibration methods constitutes the last part of the paper. The symbols shown at the top of page 197 will be used in equations throughout the paper. Dynamic and Static Gravity Methods Methods of measuring gravity fall into two groups: dynamic and static methods. The first group involves the measurement of time. Examples are: determinations of the period of oscillation of a pendulum, measurements involving the free fall of a body, and comparisons of gravity with the centrifugal force of a rotating body. Measurements in the second group of gravity methods are concerned with deflections of certain indicators when the force of gravity is in equilibrium with another comparison force.

Jan 1, 1940

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By C. A. Heiland

Measurements of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for comprehensive engineering information on the subject. The working principles of a number of gravimeters will be illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as elementary form as possible. A description of calibration methods constitutes the last part of the paper. The symbols shown at the top of page 197 will be used in equations throughout the paper. Dynamic and Static Gravity Methods Methods of measuring gravity fall into two groups: dynamic and static methods. The first group involves the measurement of time. Examples are: determinations of the period of oscillation of a pendulum, measurements involving the free fall of a body, and comparisons of gravity with the centrifugal force of a rotating body. Measurements in the second group of gravity methods are concerned with deflections of certain indicators when the force of gravity is in equilibrium with another comparison force.

Jan 1, 1940

By E. Keskinkilic

In this study, sulfide-type inclusion morphologies of a Ca-treated hot-rolled wheel steel, Grade-X, were investigated. The specimens taken from the hot-rolled products of Grade-X heats were studied. The size and distribution of elongated sulfide inclusions were examined for the heats of different S levels. Elongated sulfide inclusions were either not observed or rarely encountered when ladle analysis S content was below 50 ppm. The size and relative abundance of sulfide inclusions were reported to increase markedly when the S composition was greater than or equal to 70 ppm and the Ca/S ratio was less than 0.50. The effect of Ti addition (0.010?0.020% Ti) on sulfide-type inclusion morphologies was then investigated for heats having a sulfur content higher than 50 ppm. Addition of Ti was found to have a partial effect on decreasing the size of sulfide-type inclusions under real steelmaking conditions. Keywords Sulfide inclusions, Ca-treatment, titanium.

Jan 1, 2011

By Philip D. Wilson

SPEED is essentiaI in this war program and it is hard to keep up with developments. When the title of this paper was chosen, the contemplated magnesium production for which plants were then under construction was some 200,000 tons of metal per year or sixty times the 3350-ton production in prewar 1939. A few- days later an analysis of the President's 185,000-plane pro-gram, incendiary bomb schedules, and the additional requirements of the Army. Navy and Maritime Commission made it apparent that a much greater amount of magnesium must be provided in 1943. The new figures are huge but the censor will not per-mit their disclosure.

Jan 1, 1942