Search Documents

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Tsuyoshi Adachi

Photovoltaic (PV) system is especially taken notice as one of important renewable energy resources, because PV has potential to provide a certain amount of energy supply as well as without greenhouse gases emission. Considering recent rapid increasing demand for PV system, more expansion of PV system is expected in the future. However, some precious metals and minor metals such as silver, indium and others are used as component materials of solar cell in PV system. Even if energy supply would become renewable, strict limitation of these metals still remain because amount of natural resources and recycling of metals has restrictions intrinsically. The aim of this study is to reveal the possibility of materials supply restrictions for Photovoltaic system quantitatively and to propose several measurements to assess supply risks for materials. Especially, silver supply potential which is used as wire line in PV system as well as PV demand forecast to estimate material use in the future are focused on. We divide underlying supply risk into 5 measurements and analyze them by time series, i.e. price volatility, resource potential, recycling ratio, production type and supply concentration are investigated. Comparing these factors of silver with other metals, the potential of silver supply for PV is presented. In addition to it, we propose another method to quantify country risk applied an insurance pricing model in finance pricing theory and combine it with the supply concentration measurement. As a result, supply risk of silver will increase gradually in the near future because of its resource constraints and supply-demand balances although silver market is sufficiency competitive one. From the country risk analysis, Peru is not only a significant supply country but also has the highest country risk. Some higher risk countries will increase the level of supply risk even if the concentration ratio of supply indicates moderate level.

Aug 1, 2013

By C. W. Eggert

"The idea for this talk came to me last year when I was attending the Canadian Gold Metallurgists Meeting. I talked about it to a friend of mine who is an authority on mineral dressing, particularly the theoretical end of the business. He remarked that this was an excellent technical note, why don't you write it up. This is what I have for presentation this morning. I hope in presenting this type of idea in this way it is in keeping with the tradition of the Canadian Gold Metallurgists which was to function on a not too sophisticated level and where operators could get together and trade ideas in an informal way.My basic thesis is that it should be possible to evaluate screen analyses by the application of the standard statistical probability theory. In any statistical analysis the sample is the first consideration. If we look at existing methods of size evaluation we find it is usually based on the fact that a given particle will pass one square aperature and not another. One system of standardizing how these aperatures will be set up is based on Rittenger' s work with the ratio of hole sizes proportional to the square root of 2. Keeping in mind the limitation we have accepted this as our method of 11 sizing"" in attempting to apply standard statistical methods to screen analysis."

Jan 1, 1968

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By H. S. Puttanna

Bound water plays an important role in the processing and utilization of numerous materials and mineral processing systems. The fundamental nature of this near surface bound (vicinal) water is yet to be understood in its complete detail. The objective of this paper is to use dielectric measurements to characterize the bound water near hydrophobic and hydrophilic oxide surfaces. It is anticipated that a combination of dielectric property measurements and characteristic relaxation times will allow for more effective analysis of the interfacial water.

Jan 1, 1992

CONTENTS PAGE GEISMER, H. S.-Coal Washing Practice in Alabama. Discussed by William Kelly, H. S. Geismer, H. D. Pallister, L. E. Bryant, Milton H. Fies, Elmer F. Harris, James A. Barr, George G. Crawford, E. C. Wright, George S. Rice, R. V. Norris 1 MILLER, F. W.-Byproduct Coking in Alabama. Discussed by Theodore Swann 4 FIES, MILTON H.-Alabama Coal Mining Practice. Discussed by Milton 11. Fies, R. V. Norris, R. D. Hall, L. E. Bryant, George S. Rice, H. S. Geismer 5 MUSSEY, H. E.-Blast-furnace Practice in Alabama. Discussed by C. A. Meissner, Franklin H. Crockard, H. E. Mussey, W. H. Oldham 14 Coal Washing Practice in Alabama Discussion of paper of H. S. GEISMER, presented at the Birmingham Meeting, October 1924, and issued, as Paper No. 1363-C, with MINING AND METALLURGY, September, 1924. WILLIAM KELLY, Iron Mountain, Mich.-Is the dry-cleaning method used? H. S. GEISMER.-Neither the dry-cleaning process nor the Chance sand-liquid method has been tested in Alabama; but all other methods used for cleaning bituminous coal have been largely brought to perfection in this state. H. D. PALLISTER, Tuscaloosa, Ala.-Have you the results from the recent work on the tables with reference to fine coal? H. S. GEISMER.-None of the iron-producing companies has adopted the tables, though three commercial operators have installed tables within the last six months. I tried to learn the results, but they were not willing to release the data just now. At the mines producing domestic coal, fines present a difficult problem; until within the past six months all the fine coal was wasted. The operators are trying to recover some of it on the table. L. E. BRYANT, Rockwood, Tenn.-Is there any connection between the sulfur content of the sludge and the effect of the sludge on vegetation?

Jan 7, 1925

By Cloyd M. Smith

A FEW years ago, the Ventilation Committee established the practice of presenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measurements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies.

Jan 1, 1949

By M .. K. Stewart

(Here follows descriptive movie.) CHAIRMAN KNOX: Thank you very much, Mr. Stewart, for this wonderful paper and picture. We are indebted to you. It certainly is the most interesting thing I have ever seen in connection with wire rope, except paying for it. I think there are a lot of questions that could be asked to bring out some points that we are not generally understanding of. Are there any questions at this time? I know Mr. Stewart will be glad to answer them. Come up to the front, Mr. Stewart. MR. STEWART: That&apos;s all right, thanks. CHAIRMAN KNOX: If there are any questions, let us have them. (No response.) Well, we will pass on to the next paper. CHAIRMAN KNOX: Our next paper will be "Self-Preservation, with Some Comments on Mechanical Loading," by Benedict Shubart and Charles Schloss.

Jan 1, 1935

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By Henry Carlisle

W. W. Mein: One of the most amusing things in Nevada City – I was born and was going to school there - was that my mother made overcoats for us, and because they were different from other boys’ overcoats, we’d hide them under a bridge and pick them up on the way home. I left Nevada City with my parents when I was about eleven years old, and moved to Oakland. This was caused by the closing down of the hydraulic mines and my father being send to the El Cayo mine in Venezuela, which was then one of the richest gold mines in the world. Hamilton Smith operated the hydraulic mines in California, and when they were closed down by the Sawyer decision, he was persuaded by the Rothschilds to go to London. There, together, they formed the London Exploration Co.

Jan 1, 1964

By L. Webster Wickes

The bad effects of arsenic in commercial copper are well-known to metallurgists. The refining of copper by electrolysis eliminates practically all of the arsenic, provided certain requirements are fulfilled. The first, and most important, of these requirements is, that the voltage of the depositing current shall not be too high. It has been known for some time that the percentage of arsenic in the deposited copper increases with the voltage. To investigate the relation between the electro-motive force (e.m.f.) and the freedom of the precipitated copper from arsenic, the experiments were made, of which a brief summary is here given: I made three copper-arsenic alloys, containing respectively 3.56, 2.24 and 0.96 per cent. of arsenic. From these alloys I cast several anodes. For cathodes I used sheets of thin copper,

Jan 1, 1905

By R. W. Raymond

In June, 1906, I delivered to the graduating class of Lehigh Cniversity an address upon this subject, the substance of which, with sundry omissions and additions, was subsequently repeated, in October of the same year, in an extempore address before the Schenectady branch of the American Institute of Electrical Engineers. The latter, as stenographically reported, was published in the Proceedings of that society for November, 1906, and was referred to by President John Hays Hammond in his address at the Chattanooga meeting of October, 1908. Requests have been received from various quarters for the repub-lication of this address by the Institute. This I do not regard as necessary or proper; but I yield to that demand so far as to reproduce in the Transactions a summary of my views, as expressed in the two addresses above mentioned.

Jan 1, 1911

By Sumner M. Anderson

Anderson: Will, I have known you for only the past 30 years of your extraordinary mining career, and have often wondered just how it got started. Wright: I suppose you might say it was largely a matter of heritage. My father, who in 1886 was one of the founders of the Michigan College of Mines, was Michigan State Geologist until his un- timely death in 1888.

Jan 8, 1968

By R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and IR. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX (R) 64N) is capable of copper chelation. The effect of the structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1972

Gentlemen of the American Institute of Mining Engineers.—As you well know an application is about to be made to Congress, by the American Society of Civil Engineers, for the appointment of a cornmission composed of persons skilled in the production and use of iron, steel, and other structural materials, whose duty it shall be to test the strength, elasticity, and other quatities of such materials ; not simply the substances used as such, but the members of large structures composed of such materials, of the forms and sizes in which they are actually used. As I understand, the papers that will be read here to-night will have for their object to show the necessity for such tests, and therefore the necessity for the commission asked for. As the representative of the Society of Civil Engineers, I have to thank you, gentlemen of the Mining Engineers, for the great zeal with which yon have taken up this subject, and seconded the efforts of the Civil Engineers; or, perhaps I ought rather to say, initiated the efforts to get a suitable commission appointed to obtain most vitally important information which it is admitted on all hands we do not now possess. In drawing up the memorial to Congress, in connection with some of the ablest and best informed of our Society, and in all the discossions on the subject, I have been struck with the emphasis with which the confession is made, that so little is known of the strength of the larger-sized members constantly used in building structures of the magnitude which the present requirements of the country now demand. I presume the remarks made to-night will bring this out very prominently. This is no disgrace, for with the means here-

Jan 1, 1882

By D. Foster Hewett

The scope of this paper is the description of two districts in Peru in which deposits of vanadium have been found, and the consideration of much laboratory-work that I and others have done to determine the nature of these deposits. It is with regret that I present some of the data in a state of evident incompletion, particularly the analyses of a few of the minerals, which leaves some doubt as to whether the true nature of the migerals is understood. I make no apology, however, since in this case, as in many others referring to ore-deposits, conclusive opinions cannot be stated until a great amount of work has been done, and the deposit has been thoroughly exploited. I believe that the data and the tentative conclusions here presented indicate a unique and interesting condition which may assist others in work along similar lines; arid further, what is of more practical importance, stimulate a search for a metal which, though long considered rare, is probably so merely because proper care has not been taken to recognize it. An excellent bibliography on the occurrence of vanadium in nature is given by I?. W. Clarke in his paper, Data of Geochemistry;&apos; and in the preparation of this paper 1 have consulted many of the references contained in the Bibliography of the Chemistry of Vanadium, by M. Moisan.2 A brief review of the subject having special reference to the metallurgy of vanadium is contained in the small book by P. Nicolardot.3 One of these vanadium-deposits has already been briefly. 1 Bulletin No. 330, U. S. Geological Survey (1908). 2 Chimie Minerale, vol. iii. (1905). 3 Le Vanadium (1905).

Jan 1, 1910

By C. Y. Clayton, Francis B. Foley, Muir L. Frey

DuRing the past year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been Ied to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent. The following lengths and gages were used: LenGth, GaGe, LenGth. GaGe, Feet Inches feet Inches Starter 2 % 7 111/16 3 2 % 8 11 4 2 % 9 1 9/16 5 2 10 1 7/16 ________6_____________115/16____________________________

Jan 1, 1924

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By John T. Kuo

The miner&apos;s seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner&apos;s seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By W. E. Keck, W. C. Lowry, G. C. Eggleston

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant&apos; mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939