Search Documents

By Segnit ER, Boow J

The start up operations of Western Mining Corporation's Kalgoorlie nickel smelter encountered troubles due to the high magnesia content of the concentrates. The flash smelter slags, with higher than normal magnesia content, had a much higher melting point than the normal low-magnesia, predominantly fayalite slags usually produced in nickel smelting. Investigations were made of the structures, melting points and viscosities of the Kalgoorlie smelter slags, as produced, and with additions of silica or lime.

Jan 1, 1980

By Martin T

High methane content of the medium volatile metallurgical coal mined from the Coal Basin mines causes very difficult mining conditions. Rapid desorption into the mine ventilation system limits coal production, requires huge fresh air quantities and creates mine safety problems. In workings deeper than 2000 ft (600m) gassy coal and heavy cover create outbursting conditions. Cross-measure methane drainage has reduced ventilation requirements on advancing faces, but degasifica- tion of virgin coal is needed to improve mining Conditions.

Jan 1, 1982

By P. K. Currie, J. V. Walters

Solution mining of magnesium salts (Carnallite and Bischofite) is taking place near Veendam, in the northeast Netherlands. The magnesium salts are used for the production of magnesia sinter, used as a base material for the manufacture of refractory bricks for furnaces. This paper gives, first, an introduction to the operational procedure followed in Veendam, with the emphasis on some of the unique aspects, and then discusses rock-mechanical aspects of the cavity behaviour. The creep behaviour of magnesium salts is described, and Finite Element calculations on cavity stability and potential surface subsidence are discussed.

Jan 1, 1985

By Rabie A. S, Fouad K. M, Ammar A. A

The existence of Gabal El Kahfa ring complex, located in the Eastern Desert of Egypt, has been ascertained from aeromagnetic and aeroradiometric survey data as well as by aerial photography. Two maps for -the net aerial radiometric measurements reduced to ground level and aerial magnetic data corrected for the regional normal gradient of the earth's magnetic field have been constructed. The aeroradioactivity data have been interpreted geologically and analyzed statistically to outline various radiometric units and compute their charac- teristic statistics. The ring complex showed a circular radiometric feature and yielded a radiometric mean background and a standard deviation of 6.48 and 0.89 pR/h respectively. Besides, the observations showed a normal distribution. The aeromagnetic data have been reduced to the north magnetic pole, then filtered to produce the regional-and residual-component maps. Statistical trend analysis was conducted for the tectonic linea- ments resulting from the three magnetic maps, to define the structural framework of the area under study. This statistical study proved the exis- tence of trends in the east-west, northwest-south- east, northeast-southwest and north-south directions. The ring complex is characterized by a circular magnetic feature, whose average relief is 2150 nT. It is included within a high east-west trending magnetic zone. The latter represents a deep-seated uplift or anticline which is bordered from all sides by some faults of different trends.

Jan 1, 1988

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by complex geometry of the open pit and the surrounding natural topography of an open-pit mine. The resulting inversion cap is known to contribute to the degradation of air quality in the open pit, resulting in loss of production. This paper discusses the development and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the analyzes effect of the geometry of the mine and the slope angle of the pit on the contaminants profiles in the mine.

Feb 27, 2013

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize biomass productivity, the influence of reclamation practices on biomass production must be well understood, which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass estimations and, also, the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, experimental biomass production plots on reclaimed mine sites established in Wise County, VA, are used for a comparative study of satellite spectral derivatives, which are evaluated against groundbased biomass estimates. Metrics based on four spectral derivatives, band ratios and spectral transforms were regressed against biomass measured in situ for different species. The results demonstrate that greenness and principal component 2 (PC2) were more efficient than the other spectral derivatives for monitoring the biomass of this reclaimed area. Also, it is shown that Landsat-5 TM has provided promising results for monitoring of the biomass changes occurring from 2008 to 2010 over the study area.

By Ellen Amoako Afful, Michael Moats, Guang Xu, Ashish Kakoria

Electrowinning and solvent extraction are crucial steps in the production of high-purity copper. However, safety concerns have been raised regarding the acid mist generated from the electrowinning process. The mist generated results in health risks to workers and damage to machinery and infrastructure. Currently, chemicals and pellets are used to control acid mist. However, the effectiveness of these controls may vary depending on the type of organic solvent used in the solvent extraction process, which can influence the generation of acid mist. This study aims to evaluate the impacts of organic solvents and surfactants on acid mist suppression. In this study, an electrolyte is contacted with organic solvents to simulate the solvent extraction. The electrolyte is dosed with 20 mg/L of surfactant at each contact. Acid mist testing is performed on the electrolyte separated from the organic phase at the end of the solvent extraction step. The mist collected is analyzed to determine the level of acid mist generated. The results of this study indicate that organic solvents and surfactants showed significant acid mist suppression, but with somewhat different suppression efficiencies. After first contact, Licorice and the organic, for instance, showed a suppression efficiency of up to 69.7% but its efficiency gradually decreased as the number of contacts increased.

Feb 1, 2025

By Sir Robert Hadfield

Introduction.-I esteem it a great honor to be asked by this Institute to give them an address chiefly devoted to metallurgy. While it is with great regret that I find myself unable to be present to deliver this in person, I take this opportunity of wishing your society every success in its continued career of usefulness to the metallurgists of the great Republic. To be elected, eight years ago, along with Dr. J. E. Stead, F. R. S., as one of your Honorary Members, was a privilege which I greatly esteemed, for I consider that no society in America has done so much as ours for the advancement of metallurgy. Those who have Served our Society.-Where many have served so well, it is difficult, without appearing to make unavoidable distinctions, to select names from those of your members who have done so much for the cause we have at heart-the advance and progress of metallurgy. As typical, however, and not in any way meant as a complete list, there are among others the following names which in the past and to-day stand out prominently in this science of ferrous metallurgy. With most of those now mentioned I have personally come in contact, or by correspondence in some few cases, and have exchanged views, since I first came over to America 30 years ago. Holley; Jones; Weeks; Andrew Carnegie; Thomas Carnegie; Fritz; Sterry Hunt;. Egleston; Maunsel White and Taylor, who did so much for high-speed tool steel, and helped to revolutionize machine-shop practice; W. J. Taylor; Robert Hunt; Alfred Hunt of Pittsburg, who did so much in the early history of aluminum, and, alas! did. not live to see the wonderful progress which has been made in that particular branch of metallurgical industry; James Douglas; C. B. Dudley; Birkinbine; Howe; Metcalf; Barus; Langley; Raymond; P. H. Dudley; H. H. Campbell; W. R. Webster; E. D. Campbell; Talbot; Spilsbury; Gayley; Dinkey, under whose supervision and responsibility modern armor has been so successfully produced in this country, which the writer can testify from personal knowledge of , test results possesses very high Figure of Merit; Schwab; Kennedy; Wellman; Garrison; Wood; Moldenke; Webster; Swank; Unger; Richards; Sauveur; Strat-

Jan 5, 1914

The day after I reached New York, on January 30th, John Ryan of Anaconda told me where they wanted me to go. Late in 1916 the Russian Czar, desperate for money and supplies with which to carry on his unhappy share In the first World War, sent emissaries to the United States to see if our great mining companies might be interested in trying to find mines and to bring them to production in the millions of acres of the Imperial Estates in Russia and Siberia. It looked like a long chance as no one knew whether or where there might be important ore bodies. Even if they found them it might be a hopeless task to equip them under wartime conditions But the American copper companies had plenty of money and they were used to taking risks. They made a supersecret agreement with the Czar's deputies to send an exploring expedition to Russia at once I never learned the names of the other companies but Anaconda was to man- age the venture. Horace Winchell, then the leading mine geologist In the United States, was to be in charge of operations. Charles Janin, an eminent placer and dredge expert, was to study chances for producing gold and platinum. Though at 33 years of age I was much younger than the others, I was chosen to hunt for copper and other valuable metals. Charles Boynton, a business man who had lived in Russia and had married an attractive Russian woman, was to join the party and carry on any necessary financial or diplomatic affairs. He had gone on ahead to arrange for our reception Finally a graduate student from Ann Arbor named Steinberg was to go along as Interpreter. We soon found out that if his Russian was no better than his English his interpretlng couldn't be trusted too much I knew nothing about the millions of square miles In Russia and Siberia, and even less about what mineral deposits might be found, but I was delighted at the prospect. I was treading on air for the few

Jan 1, 1976

John C. Greenway was responsible for much of my success in the seven years from what I called the end of my apprenticeship in exploration until I entered the Army in World War I. I first met Green- way on my return from Promontorio and, as he was replacing Powell, he was to be my boss. Even at first glance you couldn't help liking and trusting him. He was tall, well built, and erect-an old Yale athlete. After college he became a captain in the Rough Riders and a friend of Theodore Roosevelt, distinguishing himself in the Cuban campaign. He made good friends in all ranks of the Rough Riders, some later becoming leaders of industry and others following Greenway where-ever he went. After the Spanish War Greenway worked for iron mining companies around the Great Lakes and when the directors decided that Calumet and Arizona needed a new manager the ones who were also prominent in Oliver Iron Mining Co. selected Greenway It was a lucky choice for Greenway and for me. He became the best manager among those who ran the big copper mines He was open-minded in encouraging discussion and even opposition-until he made up his mind. Then, in military fashion, everyone must follow his decision without question. I think this is an essential of good management. Unfortunately a few did not feel this way and they had to leave. It was characteristic of those times that respect for the boss was so great that in the 16 years in which he was one of my best friends I, like all under him, always called him "Mr. Greenway." Soon after he arrived Greenway asked the leading mine operators in the southwest, Dr. Louis D. Ricketts and James S. Douglas, son of the Dr. James Douglas who had made Phelps Dodge great, to do special work for Calumet and Arizona. I found later that the object of the study was to determine the terms on which the half-dozen Warren District properties of Calumet and Arizona were to be joined in one

Jan 1, 1976

By John C. Fowle

Having had for many years the management of magnetite mines, and having noted the various admixtures, such as jasper, " green rock," actinolite, etc., that occur so frequently in the deposits and make the fine ore so difficult as well as expensive to sort by hand, I studied the different ways of mechanical sorting, but found none eatisfactory—the universal objections being the expense, the small quantity that could be handled per hour, and the low grade of ore produced after all. Feeling that some means would be discovered ultimately for concentrating the small ore, I began at the Michigamme mine, at Michigamme, Lake Superior, Michigan, to separate it from the larger and richer lumps, by placing in all the shaft-houses screens of round iron bars set 1/4-inch apart, on which the skips were dumped as they were hoisted; the coarse ore going into one stock-pile or into cars, and the small ore, from 2 or 3 inches diameter down to powder, going into a special stock-pile, to be treated as soon as some proper means was found to separate the ore from the rock and ether impurities. Careful investigations showed that neither dry nor wet concentration was the right process for us; and I finally studied the magnetic process. Not knowing of any magnetic separator in this country that would handle such large pieces of ore as I wished to treat, I looked abroad and found in Sweden the Wenstrom separator. One of these machines was brought to the United States and tested in New Jersey and other places. (See the papers of Messrs. Cook and Birkinbine, Trans., xvii., 599 and 728.) This original separator, having 15-inch face of drum, I brought to the Michigamme mines, and, no one having confidence in it, placed it in operation at my own expense. Finding that in this way large ore could be treated much better by magnetic separators than by hand, and with much greater enrichment of the product, I put up a small, crude mill with several series of screens, so as to size the material and

Jan 1, 1891

By Robert W. Hunt

When I had the honor of presenting to the Institute at the Buffalo meeting in October, 1888 (Trans., xvii., 226), my paper on " Steel Rails and Specifications for their Manufacture," I expressed my hesitancy in submitting my ideal rail-sections. Since then, continued residence in Chicago, perhaps, or greater intercourse with railroad officials, has either given me more courage or has taught me that so little is really known on the subject that one is safe in expressing one's views, let them be ever so erroneous. As a further personal excuse, I may remind you that " fools rush in," etc. At all events, I would now call attention to certain rail-sections which I believe to be good. I do not say they are the best, but I feel sure they have more merit than the majority of the adopted heavier-sectioned rails. In determining the proper form for a rail, the subject should be considered from two points; first, and most important, the duty required ; second, and of almost equal importance, the influence of existing details of manufacture upon the character of the finished product. It is perfectly proper that all the strains to which the rail will be subjected should be considered and calculated. But its ability to resist them will depend quite as much upon the character of the metal as upon the form of its section. That which would be the realization of the ideal with good steel would be disappointment with poorer metal. Therefore, the railroad engineer should always have in mind and pay due respect to what the metal worker may give him—the may being the factór of danger to be covered by his factor of safety, and possessing greater importance than any formula laid down by never so eminent authorities. It is well-known how positive is my conviction that high heat during manufacture and good rails cannot go together; hence, if we insist upon the avoidance of this evil by rail-makers, we must give them sections which can be made at low temperatures with commercial as well as technical success. The market-price for rails controls the practice of makers, and,

Jan 1, 1889

By A. R. Marder

Fe-C alloys have been investigated at temperatures below the eutectoid transformation to determine whether the superplasticity phenomenon exists for these materials. As a result of void formation at the carbide-ferrite interfaces that led to void coalescence and premature failure, the large elongations characteristic of superplustic matem'als did not develop. It had generally been assumed that the conditions for obtaining superplasticity include: a) T/Tm =0.5, b) a strain rate sensitivity of the flow stress that results in m s 0.3, and c) fine-grain structure. Although superphsticity was not observed in the alloys studied, stress-strain rate measurements indicated that an additional condition for the existence of superplasticitv in Fe-C allovs is that the fine-wain structure be equiaxed in agveement with previous results on Zn-Al al1oys. MANY investigations have been made on the hot deformation of iron-base alloys in order to obtain an understanding of the variables that may affect high-temperature strength and ductility.'-6 However, only a few papers have studied the effect of carbon content on the high-temperature properties of iron-base alloys. Peretayat'ko and Zaikov and Wallquist and carlen4 studied the effect of carbon on strength in the y temperature range, and recently Robbins, Shepard, and sherby6 studied the influence of carbon on the torsional behavior of iron in the a and cu-plus-cemen-tite temperature ranges. In addition to studying hot deformation behavior, current investigations have also been concerned with the phenomenon of superplasticity in nonferrous materials, and, in particular, ferrous alloys. Superplasticity is identified by the increased resistance to necking that results from a high strain rate sensitivity of the flow tress. ackofenr proposed the strain rate hardening coefficient m = d log a/d log e as a measure of strain rate sensitivity and showed that m must be "-0.3 for superplasticity to exist. In addition, a fine-grained microstrcture,- a eutectic or eutectoid ornosition,- and a test temperature in the creep range (TITm > 0.5)" have also been advanced as necessary conditions for superplasticity. Although many workers""23 investigated superplasticity associated with the allotropic transformation in iron and the eutectoid transformation in steel, and recently chadler " and orrison have studied superplasticity in the a - y phase region, no one has measured the superplastic effect in the a + cementite temperature region. Therefore, the purpose of this investiga- tion was to determine the effect of carbon content, microstructure, and test temperature on the strain rate sensitivity of Fe-C alloys at temperatures below the eulectoid transformation. EXPERIMENTAL PROCEDURE Fe-C alloys with carbon contents of 0.2, 0.4, 0.6, 0.8, and 1.0 wt pct were prepared as 100 lb 54 in. ingots by vacuum-induction melting. The compositions are listed in Table I. All the ingots were soaked at 2100°F for 2 hr prior to rolling to 4 in. plate. The minimum finishing temperature for rolling was 1800°F. The plate was sheared in 10-in. lengths and tensile bars were rough-machined prior to heat treatment. The samples were heat-treated according to the schedule in Table I1 in order to obtain a fine-grained microstructure consisting of finely dispersed carbides in a matrix of small ferrite grains. All the tensile specimens were heat-treated prior to finish machining, and tensile testing was accomplished on an Instron machine in conjunction with a clamshell furnace. The buttonhead specimen configuration is shown in Fig. 1. An inert atmosphere, helium, was maintained during testing with a steel tube shroud in a bell jar arrangement. Predried helium was continually purged over the buttonhead specimens and exhausted through ceramic fiber at the bottom of the tube to keep oxidation at a minimum and to prevent

Jan 1, 1970

EVERY dry thing that burns easily and multiplies or maintains fire by its own intrinsic nature can be put into an incendiary composition and various effects are produced. Some of these things are mineral combinations, like sulphur or its oil; some others, [163v] hot, dry, and subtle substances, like saltpeter; and some are. unctuous things, like fats and oils of any kind; while some serve because of dryness, like pith and wood. Some of these things are natural and some artificial But now I set aside the search for these differences in their composition. This is what I have found among all the ancient and modern things that I have been able to seek, and first, back in the time of Alexander the Great. Marcus Graecus, who was perhaps the inventor or a great experimenter and practicer of such things, writes of many of them. I have chosen some among these, and one* is this: In order to make it, he took Grecian pitch, alchitran, live sulphur, tartar, sarcocolla, niter, and petroleum oil, one part of each, and, in addition, a double amount of quicklime. He mixed it all with oil of egg yolks. Having put it in a well-covered and closed vessel of glass or glazed earthenware under warm manure, he left it for a month. Then, having liquefied it over a slow fire, always keeping the vessel well closed, he finally put this liquor in hollow sticks, in little pots, or in vessels expressly made, all with a little fuse fitted in the middle. If I should have to do this, I would say that a little gunpowder should be put in, which should give beginning to the fire so that it would ignite more easily. I have also found that another fire is made. For this sulphur is taken, or oil of sulphur if it is possible to obtain, petroleum oil or some rock oil, juniper oil, very well-refined saltpeter, and for one part of each of these five parts of asphalt; in addition, take goose or duck fat, pure black pitch, varnish, pulverized dove's dung, and enough aqua vitae to cover all the aforesaid things.. Then it is put in a glass vessel under warm manure for

Jan 1, 1942

By Ben E. Lusk

First of all let me say what a genuine pleasure it is to be here. Acapulco certainly is a beautiful change. I'm going to spend sometime talking about change, because frankly I'm astounded at the rate of change in our world today. One good example of this, reminds me that the first time I spoke before the AIME two years ago, we were at the Ramada Inn in Beckley, West Virginia. Today we're at the Princess Hotel in Acapulco, Mexico. Now that's what I call a change. Seriously though, I'm sure you've all heard it said that the most consistent thing about our society is its constant change. Five years ago, no one could have predicted the changes we experienced in the United States during the first half of the 1970's. In the past twenty-four months alone, we have seen two presidents, three vice-presidents and hundreds of administration and government personnel changes. We have stumbled from one social crisis to another, while suffering through rising inflation, major energy shortages and labor unrest that could plunge us into a full scale economic depression. In view of these constant and unpredictable changes around us, it's obvious that we must learn to deal with change and "roll with the punches" if we are to survive. A controversial book published recently, explores in detail the various aspects of change and its impact on man.

Jan 1, 1974

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By L. Adler

Analysis of a mine roof can be based on fixed-end beam behavior. The author here analyzes the effects of zero restraint at deflecting beam supports. Formulae are given for determining permissible support deflections. Analysis of a mine roof in a bedded deposit usually follows the assumption that the behavior of the roof is analogous to a beam with both ends fixed. Yet it is recognized that the end restraint itself varies with the thickness of cover, so that at shallow depth the restraint is minimum, and at great depth, maximum.' Consequently, an analysis on the basis of fixed ends or full restraint represents only one extreme in the possible range of conditions. Since the actual amount of restraint is difficult to ascertain, a more rational approach is to consider the two extreme cases of end restraint. Such situations regarding uncertainty of the restraining effects of supports are not uncommon in structural analysis, and are handled in a like manner.' Since previous studies9)4 have dealt with full restraint, this paper will analyze the effects of zero restraint at deflecting beam supports. In such a case a mine roof with several intermediate supports becomes analogous to a uniformly loaded continuous beam on simple supports, as shown in Fig. 1A. Such a structure is statically indeterminate to a degree equal to the number of intermediate supports, n. Therefore, with the three equilibrium equations, n additional equations are needed. A number of methods exist to analyze this problem, but The Theorem of Three Moments is Simplest. The continuous beam is divided at each support into a sequence of simply supported single span beams, with the unknown end moments, as appears in Fig. 1B. Continuity requires that the common ends of adjacent beams have the same slope (Fig. 1C). eiB= B(i+l)~= ei(i+l)and MiB= Mti+I)A= Mi(i+i). [1I A Glossary of all terms is given in Table I. Furthermore, if we first consider that the supports do not deflect, the slope at a support is the sum of the slopes due to each of the individual loads shown in Fig. 2, yielding:

Jan 1, 1961

The authors have done a very thorough job in analyzing the factors affecting turndown sulfur performance at Inland's No. 4 B.O.F. While many of the results are not unexpected, it is helpful I am sure to have quantified many of the relationships that the operators rely upon daily. On the other hand, however, the results shown for ladle skimming are very surprising. I do not doubt the statistical relationship shown but I feel, based on our experience at Youngstown, that some other parameter has been ignored in the data on ladle skimming. It was our experience that by skimming our hot metal transfer ladle we could reduce our lime consumption by eleven percent while obtaining sulfur removal comparable to that shown by the authors. I would like the authors comment of similar adjustments on the lime charge that were made on skimmed heats at Inland. If not, it would seem that one could gain more desulfurization in the B.O.F. by raising the hot metal manganese than by installing a skimmer. The author's state that no comparisons are valid between the data sets for the two time periods involved because of the difference in the consumption of No. 2 Bundles. I feel this in fact is one of the important conclusions to be drawn from the paper, as there seems to be approximately a 10-20 percent difference in percent of heats that are under 0.020 percent sulfur for similar conditions, which is an extremely important difference with today's demands for low sulfur. I would like the author's comments on the difference in the amount of 82 bundles consumed. Along this same line I was quite surprised by the relatively low number of heats that had a first turn down of 0.020 percent sulfur or less. Also rather disconcerting are the conditions necessary to achieve a first turn of 0.020 percent sulfur, 50 - 60 percent of the time, as required by today's specifications. It is a problem which we are well aware of, but the numbers are still shocking.

Jan 1, 1972

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By D. M. Neil

Road-headers are one of the most popular mechanized excavators used in mining and civil under-ground construction. These machines are primarily used in soft to medium hard rocks. This paper reviews the parameters associated with the application and operation of road-headers and presents a method for estimating cutting performance.

Jan 1, 1994