Search Documents

By E. Naesgaard, Brian E. Hall, A. Amini, Advanced Geosolutions, A. Azizian

"A 2 km section of the Evergreen Line Rapid Transit Project is supported on improved ground consisting of cement deep soil mix (CDSM) panels because of highly variable and challenging soil conditions, especially the potential for seismic liquefaction-induced lateral spreading. CDSM was used as an alternative approach in place of driven piles for reducing the seismic lateral spreading displacements. An additional significant aspect of obtaining owner acceptance for CDSM was demonstrating that both seismic and non-seismic performance would equal or exceed that of using driven piles. It was recognized that, to demonstrate adherence to the seismic performance requirements, seismic design should be based on dynamic analyses (using FLAC) to estimate likely displacements and stresses/strains in the CDSM panels. One focus of the analyses was investigating the potential for cracking of the CDSM panels and the resulting displacements. This was simulated using the Ubiquitous-Joint and UBCSAND constitutive models.INTRODUCTIONThe Evergreen Line Rapid Transit Project (ELRT) is an 11 km extension of the SkyTrain system through Burnaby, Coquitlam and Port Moody in the Lower Mainland of British Columbia, Canada (Figure 1). The ELRT project is being delivered through a Design/Build/Finance model by Evergreen Rapid Transit Construction (EGRT), an SNC-Lavalin Inc. company, to the Province of British Columbia (the Province).This paper discusses the ground improvement design for a 2 km section of the alignment through Port Moody, a historic city at the head of Burrard Inlet. The alignment is located in a right-of-way of restricted width with many pinch points close to residential and commercial properties, and directly adjacent to the Canadian Pacific Railway (CPR) mainline tracks. The ground slopes from south to north across the alignment towards Burrard Inlet at inclinations of up to about 6%. Design and construction of the Port Moody section was subcontracted to SNC-Lavalin Constructors (Western) Inc. (SLCW) and SNCLavalin/ Graham Construction Joint Venture (SGJV). Construction included single- and double-track slab guideways, pocket track (where up to four to six tracks were present), and Moody Centre Station."

Jan 1, 2015

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Charles S. Barrett, F. W. Steadman

DEFORMATION bands of surprising regularity are found in large-grained polycrystalline copper after cold-rolling (Fig. I). Individual bands frequently are large enough to permit a determination of their orientation by means of etch pits and an optical goniometer. Measurements have been made on 21 areas in seven different grains, and these, combined with X-ray studies of nine single crystals that had been cold-rolled after mounting in a polycrystal-line block, have contributed to a better understanding of the preferred orientations in rolled copper just as similar studies have for rolled iron' and brass.2.3 Particular attention was given to determining orientations that are stable during rolling and to the manner of fragmentation and rotation of unstable grains. The possible role of twinning was also carefully investigated. The texture of polycrystalline copper after cold-rolling is well established by the pole figures that have been plotted by Schmid and Staffelbach,4 Iweronowa and Schdanow,5 and Brick and Williamson,3 all of which are in substantial agreement. There has been some divergence in the list of individual "ideal" orientations that have been used to describe the texture by these observers and others,6 although the orientation (110) [112]-that is, (110) parallel to the rolling plane and [112] parallel to the rolling direction-is generally recognized as the most prominent orientation and (I12) [111] one of the lesser orientations. Other orientations have been given by some observers as (236) [533], (100) [001], and (I 10) [001]. The texture of copper has also been described as (135) [533].6.1 The sum of these orientations provides a reasonable approximation to the complete pole figure, but it does not follow that these specific orientations are necessarily of fundamental significance, for the choice of indices is arbitrary, within limits. Furthermore, a detailed investigation of the ideal orientations in cold-rolled iron discloses continuous ranges of equally favored positions rather than definite positions of high stability,1 and similarly Brick's observations in a single crystal of a brass2 suggest that all orientations in the range between (110) [113] and (110) [117] are about equally stable. MATERIALS AND METHODS The material used was vacuum-cast electrolytic copper kindly supplied by L. L. Wyman, of the General Electric Co.* Slices 1/2 in. thick and 2 1/2 in. square, cut from the ingot, were rolled with 50 per cent reduction per pass to final thicknesses between 0.02 and 0.04 in., and etched to develop cube-face etch pits suitable for goniometric work.8 The etch was light on some strips and deep in others.

Jan 1, 1942

By I. Fatt

Relative permeability and relative electrical resistivity curves are obtained for networks of tubes with a tube radius distribution by means of a network of resistors used as an analog model. These curves are similar to those obtained from real porous media. The effects of pore size distribution and network structure on relative permeability and resistivity are demonstrated. INTRODUCTION Study of the dynamic properties of networks of single size tubes in paper IT' of this series has shown that the network model has flow properties similar to those observed on real porous media. The comparison of properties of single size tube networks with those of real porous media cannot be carried far because very few porous media have uniform size pores. The capillary pressure curve from most porous materials such as soil, sandstone, and sintered glass indicate that these materials have pore size distribution similar to those shown in Figs. 5-1, 9-1, and 10-I.† To properly test the network model, it is therefore necessary to compare the dynamic properties of real porous media with those of networks of tubes in which the tube radii are distributed accord- ing to the distributions in the aforementioned figures. A network in which the tube sizes are distributed cannot be treated in the same manner as a network of single size tubes. In the single size tube network, the relation between tube geometry, flow resistance, and tube volume did not have to be known if the assumption was made that whatever relation did exist was the same for all tubes in a particular network. In a network of distributed tube size, the relation between tube geometry and flow resistance must be known or assumed in order to replace the tubes by equivalent electrical resistors. Relation of Tube Geometry to Flow Resistance The interchangeability of tubes and electrical resistors in the network model is possible because of the analogy between Poiseuille's law and Ohm's law. Poiseuille's law for a cylinder is q= pr4/8µl ?P.........(1) where q is the volumetric rate of flow, µ is the viscosity, ?P is the pressure gradient, r is the tube radius, and 1 is the tube length. Ohm's law is I=1/R?E..........(2) where I is the flux and is equivalent to the volumetric rate in Poiseuille's law, R is the resistance, and ?E is the voltage gradient. Both laws give the flux as a function of the potential drop and the resistance of the medium. By analogy then, 1/R=pr4/8µl ?P...........(3)

Jan 1, 1957

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

JOHN H. NELSON, Worcester, Mass.-At our plant we have done considerable work on notch-bar testing and are farther at sea now than when we started. So far, we have been unable to get the notch-bar test to be consistent with any other known test. Lately, I have been investi-gating the effect of the position of the notch-bar specimen in a, bar. To do this I took a 3, ½ in. square bar and quartered it, then heat treated the four quarters. Each of these pieces was again quartered and a specimen machined and notched. "In this way we would have notch-bar tests from the exterior to the interior of the bar. These were made of such lengths that it was possible to make four impact tests on each speci-men. Extreme care was taken in marking the position of these test speci-mens in the original bar. The notches were then cut with relation to position of the specimen in the original bar. The second notch was cut 90° from the first, and so on around the specimen. In this way, we have found that, with a 3 ½ in. bar of 0.4 or 0.5. per cent. carbon steel when properly heat treated, we could get impact values ranging from 15 to 100 ft.-lb. Just why this is the case we are unable to state; but it does appear to be a fact that along the outside of the original bar the notch-bar test seems to be low and increases toward the center, but it is not always consistent. For instance, we may have, on a single specimen; one notch-bar test giving us 15 ft.-lb. and another 100 ft.-lb. We have not found such inconsistencies in alloy steels. Alloy steel is consistently good or consistently bad. If it. is good, you cannot readily destroy the impact value, no matter what you do; if it is bad-that is, if it is a poor notch-bar steel-and you have sufficient latitude in your draw, you may correct it. In other words, if the hardness you are working to will allow you to draw to about 1050° F.(561° C.) or over and then quench this steel from the draw heat, you. can raise the im-pact value of the steel from about 4 or 10 ft.-lb. up to-40-or 50 ft.-lb: Just what occurs I do not know. There is evidently a critical-point in steels that have poor impact value, in the neighborhood of 1000 F. to 1050° F. (536° to 561° C.).

Jan 12, 1919

By R. L. Sandefur

Professor Kim's excellent review article1 on ultimate pit planning contains a statement of the apparently widely held but incorrect belief that "kriging provides information on the confidence limits around the estimate which no other extension technique is capable of supplying." If a geostatistical approach is valid, there are several good reasons for using kriging but uniquely provided confidence limits is not among them. If kriging is possible, then confidence limits can be calculated for any other linear estimate. Kriging is the procedure which finds the weighing coefficients which minimize the estimation variance [ ] is the variance of blocks like the one being estimated. wi is the covariance of the estimated block and the i-th sample. oij is the covariance of the i-th sample and the j-th sample. Ai is the weighing coefficient for the i-th sample. N is the number of samples. The formula for estimation variance can also be used to calculate confidence limits on blocks estimated by any linear combination of sample grades including: 1) Polygons a. Hole nearest block centroid is assigned weight 1. All other holes are assigned weight 0. b. Polygonal area weighing. The samples are assigned weights directly proportional to their polygonal areas of influence within the block. The weights sum to 1. 2) Inverse distance weighing. The samples are assigned weights directly proportional to the reciprocal of their distance to some power from the block centriod. The weights sum to 1. Often only holes nearer than a certain distance and/or the nearest hole in each octant is considered. If there is an antisotropy to the ore body, an elliptical transformation often gives more accurate results. The most popular inverse distance weighing function is inverse squared distances (IDS). 3) Simple average. All samples within a certain distance are assigned the same weights which sum to 1. As an example of the applicability of the above formula to any linear estimate an internal verification on copper grade of 665 blast holes on the 1040 bench at Utah's Island Copper mine is presented. Internal verification is simple and applicable to non-linear estimates as well. Any sample (drill hole, bulk, trench, or chip) is dropped out, the value of the dropped sample estimated and compared with the actual value. If this is done for all samples, a measure of confidence limits is obtained. Internal verification is used in Cominco's MEPS system4 and in the BLUEPACK system.5 Comparison of block values against estimates697 is not dissimilar to internal verification. Results of the internal verification are presented below:

Jan 1, 1980

By F. Dubuc

"The Adams Mine of Jones & Laughlin Steel Corporation is situated on the Boston Township iron range near Kirkland Lake, Ontario. Eight different orebodies have been outlined, with a total open-pit crude tonnage of. about 100,000,000 tons or the equivalent of 30,000,000 tons of concentrate. The ore consists of fine-grained, well-bedded Early Precambrian iron-formation composed essentially of alternating layers of chert and magnetite. Grade averages about 22 per cent magnetic Fe.The iron range varies in width from 3,000 to 4,000 feet and is made up of several horizons of iron-formation, cherty ""quartzite"" and volcanic rocks. The latter consist mostly of basic lava flows and minor amounts of tuff. Dips are rarely Jess than 50 degrees, and the range is believed to represent an overturned limb of a major synclinal structure. Dykes of syenite and lam prophyre, along with local younger diabase, intrude the rocks of the iron range."

Jan 1, 1966

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by i0 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By S. I. Freedman

Coal-oil mixture (COM) combustion technology is regarded by the Department of Energy as near term, and potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers, into blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally-acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1978

By K. C. Mills, E. T. Turkdogan

The results on the rates of vaporization of Fe-Ni alloys, levitated by an electromagnetic field in a stagnant atmosphere of helium, are shown to be in close agreement with those predicted theoretically. AS shown in Part I of this series of papers, the rates of vaporization of metals enhanced by convection currents are increased further by the process of condensation of metal vapor when there is a steep temperature gradient in the boundary layer. At the time this theoretical work was completed one of the authors (K. C. Mills) had already carried out some experimental work on the rates of vaporization of molten Fe-Ni alloys. The experimental work was done under conditions which make it possible to compare the experimental rate data with those predicted on theoretical grounds. EXPERIMENTAL The object of the experiments was to evaluate the activities in a number of binary metal systems. The details of the experimental technique are given in another paper by Mills, Kinoshita, and Grieveson,2 and, for the present purpose, a brief mention of the relevant features of the experimental method will be adequate. Using an induction coil, the metal weighing about 1 to 1.5 g was levitated by the electromagnetic field in a stagnant atmosphere of pure helium. The helium was freed from oxygen and water vapor in the usual manner, and its pressure in the vaporization chamber was maintained at 1 atm through a bleeder device. The vaporization chamber consisted of a pyrex tube, 2.8 cm diam, with a side arm connected to the helium bleeder. The bottom of the tube, shaped conical, was surrounded by the induction coil, and the top was sealed with an optical flat for the purpose of measuring the melt temperature with a two-color optical pyrometer. By suitable adjustment of the high-frequency power input, the metal was brought to the desired temperature in about 30 sec of levitation. After a specified vaporization time, e.g., 3 to 4 min, the alloy was quenched by switching off the power. The amount of metal vaporized was determined from the difference between the initial and final weights of the sample. During the vaporization time, temperature fluctuations of about ±10°C were observed. COMPARISON OF EXPERIMENTAL DATA WITH THEORETICAL VALUES The experimental results are given in Table I. As already mentioned, the attainment of the vaporization temperature took about 30 sec from the moment of levitation. Therefore, the times recorded in Table I are 30 sec less than the total time; this is considered to be a reasonable estimate of actual vaporization times.

Jan 1, 1964

By George Fancher, R. L. Whitting

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By R. L. Whitting, George Fancher

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986