Search Documents

By P. K. Sims

One-day field trip via U.S. Highway 6 and Colorado Highways 119 and 279 from Golden, Colorado to Idaho Springs. This field trip provides an opportunity to observe aspects of the Laramide ore deposits in the Central City and Idaho Springs mining districts and the Proterozoic basement rocks, which host the ore deposits.

Jan 1, 1986

By L. A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof, and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests (laboratory and in situ) and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the structural parameters, as they become available through future analysis and experimentation. Analysis of the published test data suggests that pillar compressive strength (per unit of area) is proportional to the cube root of the pillar width, and that the height effect can be described as the superimposing of a variable size effect (characteristic of the material) on the constant width effect.

Jan 1, 1981

By J. E. Dorn, S. K. Mitra

The low -temperature tensile and creep behaviors of single crystals of copper were evaluated and analyzed in such a manner as to provide an estimate of the separate contributions of short-and long-range stress fields to strain-hardening. Furthermore, the average force-displacement diagram for thermally activated intep-section of two dislocations was estublished. This diagram plus a knowledge of the variation of dislocation spacing and the long-range back stresses with strain permits on accurate prediction of creep rates. The calculated activation energy for intersection under conditions of a constant strain rate increases linearly with the absolute tempevatus-e as required by theory. AN understanding of the detailed mechanisms for strain hardening constitutes one of the principal unsolved problems in dislocation theory. Two major models for strain hardening have been advanced in the past. The one that has received greatest attention assumes that strain hardening arises exclusively from long range interaction stresses between moving dislocations and piled-up arrays of blocked dislocations on the slip planes. This type of interaction was first announced by Taylor' who revealed that the back stress fields due to a simple uniform array of positive and negative dislocations entrapped in the deformed crystal would result in parabolic hardening. Shortly thereafter Andrade and Henderson" demonstrated that the strain hardening of fcc single crystals was not parabolic, as previously thought, and finally it was recognized that a typical stress-strain curve consisted of three successive stages of deformation, niz., the easy glide, Stage I, linear hardening, Stage 11, and the parabolic hardening, Stage 111, ranges. The objections to Taylor's somewhat na'ive model, which were presented so forcefully by cottrell; were largely removed by the more realistic details incorporated in Mott's analysis.5 But because Mott's theory for hardening via long range stress fields gave somewhat analogous results to that of Taylor's (inasmuch as it also predicted a parabolic rate of strain hardening whereas the observed rate of strain hardening in Stages I and I1 were linear), it was not widely accepted. Major consideration was therefore given to models, such as those which were advanced by Friedel and seegere that were formulated for the ad hoc purpose of yielding linear rates of strain hardening. The second major thought regarding strain hardening is based on the concept that it arises principally from short-range stress fields due to the interactions between intersecting dislocations. Cottrell and stokes7 showed, several years ago, that the constancy of the flow stress ratio at two temperatures regardless of the strain was inconsistent with the concept that strain hardening arose exclusively from long-range back stresses. The argument that strain hardening was primarily due to local interactions of intersecting dislocations was presented in considerable detail by asinski.' Extending Basinski's method of analysis of the intersection process, Mitra, Os-borne, and dorn recently demonstrated that indeed the strain hardening in aluminum single crystals arises principally from local effects coincident with intersection; however, these conclusions, too, must be modified, as will be shown later in this report. The present investigation, devoted principally to the low-temperature deformation of copper single crystals, was initiated in an attempt to ascertain whether or not the same conclusions arrived at for aluminum also apply to metals, such as copper, which have much wider stacking faults. It was soon observed that the strain hardening in copper could not be attributed exclusively to local effects between intersecting dislocations. Previously no analytical method for arriving at the possible simultaneous contributions of long-range stress fields and localized forces on intersecting dislocations was available; consequently, the separation of these two factors could not be readily accomplished. In the present report a method of estimating the separate contributions of each of these two factors to strain-hardening will be presented. The authors will show that both long-range stress fields of the type contemplated by Seeger and Friedel as well as short-range forces of the type considered by Basinski are responsible for strain hardening in fcc metals at low temperatures. This method of analysis also accounts for, in a satisfactory way, the effect of stress, temperature, and strain on the creep rate under constant stress. Furthermore, in the course of presenting their methods of analysis the authors will also reveal the rather complete agreement of their experimental data with the concepts of the theory for thermally activated intersection of dislocations. INTERSECTION MODEL As shown by seegerl0 the strain rate arising from thermally activated intersection of dislocations is given by

Jan 1, 1962

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By A. H. Larson, T. P. McNulty

RECENTLY, an investigation of the absorption of sulfur dioxide gas in molten binary copper alloys was conducted. A Sieverts-type apparatus, consisting of a mercury-filled gas dispensing buret and a mercury manometer, was used initially for determining the volume of gas absorbed as a function of pressure. The equilibration behavior of the alloys studied indicated that the mercury in the gas measuring system was absorbing sulfur dioxide. Owing to the widespread use of mercury as a displacement medium in absorption studies, an investigation was made to determine the nature and magnitude of the mercury - sulfur dioxide absorption effect. The gas measuring system was modified by substituting a Worden Quartz Products Type PDHV fused-quartz-spiral pressure gage for the mercury-filled dispenser and manometer. The dispensed gas volume at known temperature and atmospheric pressure was measured by evacuating a Pyrex vessel of known volume and by admitting sulfur dioxide into the vessel until the attached quartz pressure gage registered atmospheric pressure. Atmospheric pressure was measured concurrently with a separate mercury barometer. The volume of the empty sample chamber and its attendant apparatus was determined by measuring the equilibrium pressure accompanying the addition of a measured volume of sulfur dioxide into the initially evacuated system. The volume of the mercury sample was calculated from the density of mercury at the temperature of the study (25°C). Measured volumes of sulfur dioxide were then dispensed into the system and the equilibrium pressure accompanying each gas addition was determined. From the difference between the system volume and the mercury volume, the number of moles of gaseous sulfur dioxide remaining in the system at each pressure was calculated. The difference between the number of moles of gas dispensed into the system, denoted Enso2: and the number of moles of gas remaining in the system after absorption equilibrium had been attained, denoted nso2(g), was equal to the number of moles of absorbed gas, denoted nSO2. The number of moles of absorbed gas was then converted to absorbed volume, denoted VSo2, in cu cm at stp conditions of (PC and 760 mm Hg. Table I contains calculated values of Snso2, nSo2(g), and VSo2 for different sulfur dioxide pressures. In the original system, denoted Run I, volume limitations of the gas dispensing system prevented absorption studies at equilibrium pressures near atmospheric pressure, so a different gas dispensing system, denoted Run 11, was used for determining the last pressure reading in Table I. The data in Table I are expressed in terms of the absorption of sulfur dioxide in 49.68 cu cm of mercury. In Fig. 1, these data are expressed in terms of the absorption of sulfur dioxide in 100 cu cm of mercury. Since the absorption data plotted in Fig. 1 show a linear relationship, the volume of sulfur dioxide absorbed in mercury is a function of the first power of pressure. The absorption reaction is So2(gas) = SO2 (in Hg) The first-power pressure dependence, coupled with the fact that the sulfur dioxide could be removed from the mercury by applying vacuum, indicated reversible

Jan 1, 1967

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By R. D. Pehlke, P. D. Goodell, R. W. Dunlap

The rate of dissolution of steel bars in molten pig iron has been measured experimentally in the temperature range 2300° to 2650° F. The rate of solution is shown to be a .function of bath composition, temperature, and stirring. A kinetic model based on carbon diffusion in the liquid phase has been derived to fit the experimental results. THE rate of scrap melting has long been an important variable in steelmaking operations. With the advent of the oxygen steelmaking process and the accompanying shorter heat times, the rate of scrap melting has now become one of the rate-limiting factors in steel production. As observed in commercial practice, the solution rate is influenced by the compositions of liquid and solid, the temperature, agitation, and time. However, no definitive work has been done on the Fe-C system, and there is very little information in the literature regarding the relative effects of these variables in steelmaking systems. A number of questions have been raised in regard to scrap utilization in basic oxygen steelmaking operations. Consideration has been given to the optimum size and shape of scrap, and to the use of preheated scrap as a means for decreasing the pig-iron requirement in oxygen blowing. The determination of an optimum scrap practice for a specific installation depends to a large extent upon the economics of the scrap market and also upon the behavior of scrap in the vessel. The present research was undertaken as a preliminary study in evaluating the behavior of steel in a pig-iron bath under various conditions of temperature, composition, and agitation, as might be encountered in oxygen converter operations or in any steelmaking operation where scrap behavior is an important process variable. Related studies have been carried out on non-ferrous systems. The solution rate of solid aluminum in a molten A1-Si alloy has been studied.' Furthermore, the increasing use of liquid metals has created considerable interest in studies related to dissolution of a solid in a liquid, or mass transfer taking place between a solid interface and a liquid metallic phase.2-10 In an effort to clarify the relative importance of factors influencing the dissolution of scrap in Fe-C alloys, this paper presents the results of a study of the rate of dissolution of a low-carbon steel cylinder in a molten Fe-C bath at various bath compositions, temperatures, and conditions of agitation. An attempt has been made to determine the mechanism of solution, and a model has been derived to fit the experimental results. The rate of heat transfer between the molten pig-iron bath and the solid-steel cylinder has also been studied. EXPERIMENTAL PROCEDURE A molten bath of pig iron (nominal composition 4.2 pct C, 0.5 pct Mn, 0.8 pct Si)* was held in a 200- *In view of the fact that the composition of the pig-iron bath was slowly changing with time because of steel dissolution and reaction with the surrounding atmosphere, intermittent samples of the liquid bath were taken throughout each experiment, Table 1. lb induction melting unit. The internal diameter of the furnace was 8-1/2 in. and the bath depth approximately 14 in. Cold-finished 1020 steel cylinders of 1/2-, 3/4-, 1-, 1-1/2-, and 2-in. diameters were cut into 1 -ft lengths for use as test specimens. One end of each bar was machined to fit a hand-driven, mechanical stirring device which rested on top of the furnace. This fixture permitted 7 to 8 in. of the bar to be immersed in the melt. The steel cylinders were cleaned to free the surface of grease and oxide. The rods, at ambient temperature, were immersed into the molten pig-iron bath. The melt temperatures studied in this investigation were 2300°, 2500°, and 2650°F. Different agitation conditions were achieved by operating with a) the power to the furnace, giving induction stirring; b) induction stirring plus mechanical stirring, using hand rotation with a chain and sprocket assembly at approximately 200 rpm; c) mechanical stirring alone with the power off; and d) the power off and no mechanical stirring resulting in minimum agitation, i.e., only that caused by natural convection currents in the bath. The samples were immersed in the melt for prescribed times ranging from 30 sec up to 6 min. Immersion times were measured with a stopwatch and temperature control of the melt was achieved by power adjustment following temperature measurement with an optical pyrometer. The measurements with the calibrated pyrometer were checked out to within less than 10°F with simultaneous thermocouple measurements. Following immersion, the bars were water-quenched and the diameters were measured with a micrometer at several positions on the reduced area, and by volumetric displacement. The dissolution rates calculated from the

Jan 1, 1965

By Robert A. Cook

In the increasing struggle to cheapen the cost of our iron and steel products a great deal of attention lias been given to economies in the manufacture of coke; and while but little lias been accomplished in this direction in the United States, the narrow margin between cost and market-price, which has obtained here for the past few years of continuing manufactur ing depression, has brought the coke-maker face to face with the problem, how to save, and benefit by it, the hitherto waste products of distillation. I These may be summed up under three heads, generally rank ing, in value, in the following order: 1. Ammonia salts.. 2. Oil- or tar-products. 3. Gas. There are cases in which the last may assume the position of greatest importance. The greatest obstacle encountered by the American coke maker, on investigating the subject, has been the apparent necessity of discarding his existing plant of bee-hive ovens, and erecting an entirely new and very expensive system of retort ovens, against the product of which Be has probably been prejudiced from his earliest knowledge of the subject. The object of this paper is to bring prominently before our coke-experts a brief history of the development at Sheffield, England, of a most successful system of the utilization of by products in connection with all already existing plant of bee hive ovens. This system has now been in satisfactory operation for about five years, and is applied to a series of blocks of ovens, comprising-about 140- in all At this plant, belonging to the well-known firm of Newton,

Jan 1, 1897

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By Warren L. Howes

Literally hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be dues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations: grinding capacity usually is the greater consideration. Grinding Capacity Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell linen

Jan 1, 1947

By Warren L. Howes

Literally hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be dues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations: grinding capacity usually is the greater consideration. Grinding Capacity Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell linen

Jan 1, 1947

By J. G. Bartram

Jan 1, 1934

By Warren L. Howes

LITERALLY hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be clues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations,1 grinding capacity usually is the greater consideration. GRINDING CAPACITY Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. [ ] From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell liners

Jan 1, 1945

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Manlapig E. V

ABSTRACT- I Results are given for a series of tests in which a 300 mm pilot-scale Jameson cell has been used in copper recleaner flotation, and for the flotation of a lead rougher feed. the results indicate that the production rate of solids, at the same superficial air velocity Jg, is higher than in conventional columns. Thus in the copper recleaner application, the pulling rate reached 14 gm/cm2/min compared with between two and three for an operating column, while in the lead cleaner application the comparable figures were 12 - 14 gm/cm2/min for the Jameson cell vs 8 - 9 gm/cm2/min for a test column. A froth crowder was used to increase the air superficial velocity Jg in the Jameson cell in the copper recleaner, while holding the collection mechanism and pulp feed rates constant. The recovery increased from 50 per cent to over 90 per cent, suggesting that recovery is controlled mainly by the froth conditions, rather than the particle-bubble interactions in the Downcomer.

Jan 1, 1991

The April General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th April, 1969, at 4.30 p.m. Mr R. C. J. Goode (president) was in the Chair. There were also present nineteen Members, including Messrs R. J. Adamson, F. P. Bath, J. K. E. Douglas, A. R. C. Fowler, P. Lambooy, D. G. Maxwell and J. A. Nixon, (Council Members), Messrs E. L. Atkinson, I. R. Chaston, J. L. Edwards, J. S. Hall, S. A. Hancox, A. F. Lee, W. K. B. Loftus, H. S. Simpson, A. N. Shand, R. A. Wilson, H. J. Wright and J. E. Van Leeuwen. Nine Associate Members, including Messrs O. Davel, G. Douglas, P. R. Garcia, D. J. Murphy, D. Rankin, G. Schwartz, H. N. Singer, S. Thompson and D. A. Viljoen. One Graduate Mr D. Bosley. Ten Visitors, including Messrs S. Adler, C. E. Alvey, B. J. Botha, K. Chant, L. W. Davis, R. N. Guest, R. V. Keet, E. G. Keown, M. D. Lourie and S. McMurray. Secretary Mr D. C. Visser. Total present: Fourty-one. MINUTES The President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Kenneth Sinc1air Rae, Ian Robert Malcolm Chaston. Associate Members: Norman Isaac Thomas, Ian Connell Robinson. Graduates: Simon Richard Jeremy Perkins, Bleddyn Reginald Lear, David Williams. Affiliate: Richard Robert Will. Students: Angus David McElwee, Clive Renard Archer, Peter Andrew Locke. MEMBER TRANSFERRED TO A HIGHER GRADE From Graduate to Associate Member: Patrick James Burns. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause). GENERAL BUSINESS The President reminded members that a buffet supper at a cost of 55c would be available after the meeting. PAPER FOR PRESENTATION The President noted with pleasure that a strong contingent from De Beers and the Finsch Mine were present. He expressed gratitude to Mr Loftus for coming

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By M. L. Whisman

Radiotracer techniques were developed for stoichiometric studies of photochemical reactions associated with atmospheric smog formation. Stock blends of separate hydrocarbon and oxygenated compounds were prepared and calibrated. 14C-labeled reactants and products in reaction systems involving hydrocarbons and nitrogen oxides at the ppm level were analyzed for qualitative and quantitative data. Precision and accuracy of these methods developed by the Bureau were determined by replication and statistical treatment of data, and these methods are described.

Jan 1, 1969