Search Documents

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By Glenn H. Damon

Concern about environmental pollution goes back many centuries, but until recently most efforts to control it have been perfunctory and spasmodic, aimed largely at coal smoke and other visible pollutants. Air pollution is to a large degree a byproduct of our economic development, and scientific knowledge of the causes and character of such pollution is more extensive than the technology to handle the waste byproducts of our industrial civilization. The removal of all constituents foreign to the air from the effluents produced by an industrialized society is obviously impractical at this time. There is widespread difference of opinion regarding acceptable ambient air concentration levels for the Various pollutants produced by combustion processes, but there is basic agreement that the pollution of the atmosphere must be controlled and eventually reduced. The magnitude of the air pollution problem has been increasing rapidly because our expanding economy calls for an ever-increasing consumption of energy, and fossil fuels are a principal source of energy. For example, the consumption of electricity has been increasing at an average annual rate of approximately 8 percent over the last 10 or 1.5 years. Table 1 shows the estimated emission of the principal pollutants into the atmosphere in 1966. The approximately 90 million automobiles, trucks, and buses on American highways contribute the largest proportion of pollutants to the atmosphere, but that fact does not alter the growing problems of the coal industry. You will note that sulfur oxides, particulates, and nitrogen oxides are all products of the combustion of coal. Of these air contaminants, sulfur oxides are now receiving major emphasis in terms of research to develop effective means for control, Table 2 shows that the combustion of coal produces approximately 60 percent of the sulfur oxides discharged to the atmosphere. While the utilization of coal is the principal source of particulate matter, this is not considered as serious a problem as it was in the early part of the century because of technological developments that have produced sound methods for the removal of particulates from waste gas streams.

Jan 1, 1968

By Simon B. Blancher, Malo Rousseau, Renato Contessotto, Thomas Wallmach

The Manganese division of the ERAMET group extracts manganese ore in Gabon and produces manganese alloys for the steel industry. ERAMET has an economic interest to maximize the ore throughput without reducing the lifetime of its manganese mines. This can be achieved by means of research and development leading to innovative ore beneficiation processes. For this purpose, the ERAMET research center has designed and constructed a new pilot plant for ore beneficiation by physical separation processes. This pilot facility was erected within an infrastructural and synergetic framework, including competencies in hydrometallurgy, pyrometallurgy, numerical modelling, analyses and mineral characterization that provide ideal research conditions. After laboratory scale tests, a pilot operation of beneficiation of low grade Mn ore (around 35% Mn) was carried out by jigging of the 1-10 mm fraction. This gravity separation process exploits density differences between the various Mn-bearing minerals such as pyrolusite and lithiophorite as well as gangue minerals such as silicates and iron-hydroxides. Enrichment leads to the production of a marketable product associated with a high mass recovery (53% for the jigging step). However, 20% of pyrolusite and 30% of lithiophorite are lost in the waste. Mineral characterization has shown microtextural complexities, but grinding the ore to approach the liberation mesh was not an option due to commercially defined constraints given by the ferro-alloy industry. Recovery of the Mn-bearing minerals or adjustments of the feed grain size (6.3-10 mm) are two potential areas of process improvements identified by means of Qemscan® mineral characterization. This paper details the process tested on a pilot scale (0.5 t/h), which has led to a significant increase in the beneficiation of a low grade Mn ore.

Jan 1, 2016

By Victor Maksaev, Marcos Zentilli

"Abstract - The Domeyko Cordillera, the westernmost uplifted crustal block of the composite High Andes of northern Chile (20°S to 28°S) hosts a narrow N-S trending belt of Late Eocene-Oligocene giant porphyry copper deposits, which include Collahuasi, Chuquicamata, El Abra, La Escondida, and El Salvador. These deposits are spatially and genetically associated with the closing igneous activity along this range, prior to a 30 km eastward jump of the magmatic front in response to tectonic plate interaction. The porphyry copper deposits are also spatially associated with a major intraarc strike-slip shear system, the Domeyko Fault System. Although the tectonic uplift of the 3000 m to 5000 m high range has generally been assumed to be mostly Miocene in age, field relationships suggest that the Domeyko Fault System and tectonic uplift were active as early as the Eocene, coinciding with porphyry copper emplacement between 41 Ma and 30 Ma. Apatite fission track (FT) thermochronology provides both age data and a time-temperature history for rocks since they cooled below a temperature of ca. 125°C (equivalent to a depth of 4 km to 5 km under normal geothermal gradients) on their way to the surface during exhumation, or after a heating event. Apatite FT data from the Paleozoic crystalline basement of the Domeyko Cordillera indicate that at least 4 km to 5 km of rocks were eroded during exhumation of this tectonic block between ca. 50 Ma to 30 Ma (Middle Eocene to Early Oligocene), a time that immediately precedes and overlaps with the emplacement of giant porphyry copper deposits. The FT data constrain the age and duration of a period of crustal thickening and extensive erosion known as the Incaic compression, an event recognized in the Andes of Chile and Peru. Assuming that cooling was due to denudation alone, modelling of the FT data allow estimation of denudation rates between 200 and 100 m/My during this period. In contrast, exposures of pre-porphyry Paleocene intrusives on the western edge of the Domeyko Cordillera reveal apatite FT ages that are concordant with biotite 40Ar-39Ar dates, indicating shallow emplacement, fast cooling and negligible exhumation. The apatite FT ages of the Chuquicamata and El Abra porphyry copper deposits are only marginally younger than their 40Ar-39Ar dates, implying fast cooling/exhumation of shallow mineralizing systems (ca. 2 km to 3 km). Their FT time-temperature history is compatible with extremely low rates of exhumation (ca. 50 m/My) since about 30 Ma (Early Oligocene). This limited extent of erosion, due to exceptional aridity, has greatly contributed to the preservation of rich supergene enriched blankets above some of the porphyry copper deposits.A model is proposed, which is consistent with field relationships, geochemical, and geochronological data. High relative velocities and intermediate-angle oblique convergence between the Nazca and South American plates in the Eocene-Early Oligocene led to intra-arc transpression partitioned into reverse faults of opposing vergence and a right-lateral shear system (the Domeyko Shear System) localized along the magmatic front. Crustal shortening and thickening led to uplift within the Domeyko Fault System and to erosion of at least 4 km to 5 km. Crustal thickening deepened the zone of magma generation, and magmas accumulated in the lower crust, allowing small volumes to rise rapidly to shallow levels along transtensional domains of the regional shear system. A similar model of crustal thickening and shortening before and during porphyry copper emplacement in zones of transtension may also apply to the Miocene-Pliocene giant porphyry copper province of central Chile."

Jan 1, 1999

By Norman Pilling

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. TIN is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper-i. e., copper containing from 0.03 to 0.10 per cent. of oxygen-apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 2, 1926

By Paul F. Kerr

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 t- 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre-Cambrian.

Jan 5, 1953

By Y. G. Shiau, J. E. Burke

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By X. T. Zeng, X. Z. Ding, W. R. Chen, L. R. Zhao

The effect of deposition defects in metal nitride coatings on erosion behavior is presented. AlCrN, AlTiSiN, TiSiN and TiSiN:MoS2 coatings were fabricated by reactive cathodic arc evaporation and unbalanced magnetron sputtering processes. The microstructure and mechanical properties of the coatings were characterized by X-ray diffraction, scanning electron microscopy and nanoindentation, and the erosion property was assessed by solid particle impingement testing. The erosion characteristics on the coating surface and cross section were analyzed and correlated to the defects, which played an important role by promoting formation of erosion pits.

Jan 1, 2006

By Parks T. C

A low-grade disseminated nickel sulphide serpentinite ore from W.A. had a relatively high permeability after drying. Various techniques indicated that the permeability resided within a fine network of fibrous vein- lets and especially within coarse cracks along which the sulphides lay. The ore minerals were therefore open to selective extraction by chemical leaching. A IM ammonia-7.8 wt.o "ammonium carbonate" solution, oxygenated at 1 bar oxygen pressure and about 23¦C, released nickel, copper and cobalt from the sulphides, leaving a permeable residue of goethite, while calcium, magnesium and iron concentrations remained negligible in the leachant. The nickel and copper was electrodeposited directly from the pregnant liquor in a deposit which included 16.5 wt.% sulphur. Enhanced copper/ nickel ratios early in the extraction suggested that valleriite (not amenable to flotation) was leached preferentially. Th$ controlling influence of the pore structure was demonstrated by the dependence of leaching rates on the size of the ore particles used, and on the measured porosity of different ore samples. A 2mm size was probably the optimum for exposing sulphides to the leachant. Leaching was accelerated by increasing the temperature and oxygen pressure.

Jan 1, 1974

By G W. Wilson

Net solar radiation is one of the key factors affecting evaporation from soil covers on waste rock dumps. While net solar radiation is normally taken as a uniform parameter over a site for modelling purposes, there can be significant variation in the radiation actually received on various portions of the dump. These variations are a function of the difference in the cover slope and direction of exposure. A predictive model has been developed to calculate the actual radiation received on the dump surfaces, based on the net radiation data measured at a weather station on a horizontal surface. The model has been designed for application at any mine site in the world, and can be used in conjunction with evaporative flux models to help estimate the effect of three-dimensional variations in the cover surface exposure. The waste rock dump at Equity Silver site (located in British Columbia, Canada) has a barrier-type soil cover system to limit oxygen entry and water infiltration. This cover has been monitored for the past nine years. The new net solar radiation model has been applied to this site and the predicted net radiation was compared to the values of actual net radiation measured on the site. The predicted variations in net radiation over the three-dimensional surface of the waste rock dump have been applied to calculate spatial variations in potential and actual evaporation (or evapotranspiration) from the site. Preliminary analyses indicate actual evaporation from a site at this latitude could vary by a factor of two for exposed versus shaded slopes. The implications of these variations for the site are considered.

Jan 1, 2003

M INE production requires the coordination of the talents of men and the use of equipment. Mine operators maintain a continual surveillance of equipment, looking for improvements and modifications that will benefit them. Few give similar attention to the advances made in the education of mining engineers since they themselves graduated. That is not surprising. Education lacks the advertising budget available to manufacturers. A modification to improve a mechanical contrivance is advertised, and an advertiser's press releases get attention by publishers. The whole program for mining engineering education could be revolutionized and no one, except a few professors, would know about it. The Canadian Institute of Mining and Metallurgy's newly established General Commit-tee on Education can improve that situation. Nine groups of engineers in Canadian universities are trying to give undergraduates an education that will make them useful to the mineral industry as mining engineers. The tabulation offered here (Table I) is an analysis of the distribution of the undergraduate-teacher contact time.

Jan 1, 1963

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By C. E. Shoenfelt

Wildcat drilling in the Rocky Mountain region did not suffer as large a decline in 1942 as was anticipated. The drilling program laid out by the Government at the beginning of the year stressed wild-catting operations and called for reduction of drilling in proved fields. The increased wildcatting campaign did not yield a great many new discoveries, nor important extensions to old fields. Several interesting wildcat wells were drilled in Colorado in 1942 but no new fields were discovered. The Wilson Creek field was extended and about 400 acres added to its reserves. In Montana two new oil fields and two small gas fields were discovered. The developments in the marketing situation had improved, however, making the prospects especially bright for 1943, as will be shown presently in the section on Montana in this report. In New Mexico eight wells were completed, which constituted discoveries ol either oil or gas but none of these was of major proportions. In Wyoming one new oil field and one new gas field were discovered, and one old oil field and one old gas field were extended. Most important was the disco-very of prolific oil producers in deeper sands in three old oil fields, of which one at least, Elk Basin, probably is of major proportions. Government Action On Dec. 26, 1942, President Roosevelt signed the O'Mahoney bill, calling for a flat 12.5 per cent royalty on lands in the public domain. It is expected that the enactment of this bill will encourage wildcatting in the public land states. Opportunity for a full discussion of the problems of reserves and production was afforded at the hearings conducted on the O'Mahoney bill by the minerals subcommittee of the Senate Committee on Public Lands and the statements submitted at these hearings last fall placed the situation, its causes and the logical remedy, clearly on record. It was established at the hearings that for several years the volume of oil discovered per wildcat well drilled has steadily declined; new fields discovered have not been of major proportions; drilling costs have advanced rapidly; a sharp decline in exploratory drilling took place in 1942, while the proportion of dry holes increased; the inescapable conclusion is that to find new reserves the search for oil must be intensified and much more wildcat drilling ' must be done. To ensure an adequate drilling campaign, the Petroleum Industry War Council, the Interstate Compact Commission and other representative oil organizations have voiced by resolution their opinion that an upward revision of crude prices is necessary to provide an incentive to the prospector to undertake the hazards of wildcat drilling, since statistics prove that only ope in five or six wells drilled results in actual production. Former Price Administrator Henderson rejected the recommendations for price increases and declared himself unalterably opposed to a general price advance, On the ground that such advances would contribute to inflation. Now that Mr. Hender-

Jan 1, 1943

By W. A. Padgham, H. Helmstaedt

Field evidence for current hypothe e about age and kinematic ignificance of gold-bearing hear zones in the Archean Yellowkni fe greenstone belt is reviewed , and it is concluded that major disagreements between previous workers are a direct result of differences in stratigraphic and tructural in terpretations of the Yellowknife Supergroup. Although goldbearing hear zone appear to be confined to the mafic volcanic pile of the Kam Group. it can be shown that shearing affected all supracru tal rocks, including the Jackson Lake Formation. now con idered to represent the youngest unit of the Yellowknife Supergroup. tructural ob ervations are incompatible with the hypothe is that the hear zones represent loci of ynvolcanic gravity sliding but are consistent with earlier conclu ions that shear zone development commenced with rotation of the volcanic pile and continued as re ult of lateral shortening broadly overlapping with the emplacement of granitoid batholiths. Shear Zones are common throughout the entire green tone belt. yet productive zone are confined to the Yellowknife Bay Formation of the Kam Group and localized where flow abut with a high angle again t the contact of the We tern Plutonic complex. However. no obvious tructural and lithological features have been recognized that are more favorable for gold deposition and distinguish the shear zones and flows of the area around the mines from those of other parts of the greenstone belt. The model that gold wa transported by metamorphic solutions and that hear zones were the firs t-order control for gold deposition provides no explanation for the trong localization of the depo it . As porphyries with elevated gold contents are present in and near ome of the mines. the possibility that gold was deposited from hydrothermal system around fel ic intrusion representing early phases of the Western Plutonic complex should be given erious consideration.

Jan 1, 1986

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By Todd S. Webster, Matthew J. Pierce, Brad D. Krumel

With the Working Shafts and Starter Tunnel under way, it became apparent this 4.7-mile, 19-foot diameter wet weather tunnel was going to live up to its name. The shaft’s pre-excavation grouting was completed, and ground water inflows were slowing project progress. As the tunnel drive was approaching 50% complete a cooperative effort was underway between the owner, engineer, and contractor to raise the base of the Retrieval Shaft by 65 feet to avoid ground water infiltration construction challenges. The tunnel alignment needed to be raised in kind. The project was behind schedule and rethinking the cast-in-place adit work was next on the agenda due to the very wet environment in the tunnel. The race was on to finish the project within the owner’s time constraints while completing multiple redesign aspects of the tunnel alignment and associated adit construction. This paper will evaluate original design criteria and actual in-route design modifications and change management to meet the owner’s just-in-time schedule needs.

Dec 1, 2022

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990