Search Documents

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By S H. Son, M K. Wang, H K. Jeong, B K. Cho, J I. Park

The utilisation of low-grade raw materials such as fine iron ore and semi-soft coking coal, and reduction of CO2 emissions are important issues in the ironmaking process. To solve these issues, a new process called PosPRA (POSCO prereduced agglomeration process) has been developing at POSCO. It focuses on the reduction of carbon composite iron ore briquette in travelling grate. In this study, the possibility of manufacturing the prereduced agglomerate (PRA) under oxidising atmosphere with travelling grate and the optimum manufacturing conditions of carbon composite iron ore briquette are investigated. The results have shown that controlling the temperature and oxygen potential in the range from 1100 to 1200°C and below 10 vol per cent respectively is very important to increase the reduction efficiency of briquette in travelling grate. High quality properties of the green briquette and PRA could be manufactured by using the briquette mixed with 20 wt per cent of coal under 0.1 mm in size under compacting pressure in the range from 3 to 7 t/cm. Adding 1 wt per cent water as a binder is proper under the condition of high compacting pressure. In a pot grate test, the compressive strength and metallisation degree of PRA are achieved over 150 kgf/p and about 55 per cent respectively, at bed temperature 1150°C and oxygen potential of 10 vol per cent when 20 wt per cent of coal is mixed in the briquette.CITATION:Wang, M K, Son, S H, Park, J I, Jeong, H K and Cho, B K, 2017. Development of prereduced agglomeration process using carbon composite iron ore briquette in travelling grate, in Proceedings Iron Ore 2017, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

By C. Marais

The use of machine vision in the monitoring and control of metallurgical plants has become a very attractive option in the last decade, especially since computing power has increased drastically in the last few years. The use of cameras as a non-intrusive measurement mechanism not only holds the promise of uncomplicated sampling but could provide more consistent monitoring, as well as assistance in decision making and operator and metallurgist training. Although the very first applications of machine vision were in the platinum industry, no automated process control has been developed for platinum group metals (PGMs) as yet. One of the reasons is that to date froth features could not be related to key performance indicators, such as froth grade and recovery. A series of laboratory experiments was conducted on a laboratory-scale platinum froth flotation cell in an effort to determine the relationship between the platinum grade and a combined set of image features and process conditions. A fractional factorial design of experiments was conducted, investigating 6 process conditions, namely air flow rate (x1), pulp level (x2), collector dosage (x3), activator dosage (x4), frother dosage (x5) and depressant dosage(x6), each at levels. Videos were recorded and analysed to extract 20 texture features from each image. By using artificial neural networks (ANN), the nonlinear relationship between the image variables and process conditions and the froth flotation grades could be established. Positive results indicate that the addition of image features to process conditions could be used as sufficient input into advanced model based control systems for flotation plants. Keywords Flotation, machine vision, image analysis, neural networks.

Jan 1, 2011

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a 'possibility, and that it was unlikely that a small bore...

Jan 1, 1950

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

Marble deposits of dolomitic variety are available in large quantities in India and for extracting these deposits diamond wire saw cutting machine is mainly used. Cutting performance of the diamond wire saw machine depends on rock parameters, machine parameters and operational parameters. Rock parameters related to physico-mechanical properties, such as, compressive strength, tensile strength, shear strength, modulus of elasticity and abrasion resistance of marble play role in determining cutting rate and beads wear rate. Thus, this study was undertaken to determine the relationship between different physico-mechanical properties and cutting performance. This work also aimed at enhancing the cutting performance of diamond wire saw in dolomitic marble deposit. Study was conducted in the field at three different zones having deposit of soft, medium hard and hard dolomitic marble. During the study, cutting rates and wearing of diamond beads were recorded in the field. Physico-mechanical properties were determined in the laboratory. The results obtained were subsequently evaluated by using statistical analysis. Study revealed that these properties of marble play a significant role in the performance of diamond wire saw machine. Predictive equations for the wearing of diamond beads and cutting rate were developed based on regression models. Results of this study will be of ample use for operators of wire saw to achieve maximum cutting performance and for manufacturers in designing the diamond beads.

Dec 6, 2010

By D. R. Brox, J. Levell

The Montana Tunnels Mine was mined out to a depth of 900 feet at the end of 1999. The first signs of instability were recognized in 1996 along the upper slope area of the northwest sector when the pit was mined out to a depth of approximately 500 feet. To extend the life of mining operations, it has been proposed to extend and steepen the northwest highwall to a depth of 1000 feet. Slope stability analyses were carried out using the UDEC software program to assess the stability and deformation of the proposed highwall design. Back analysis of an instability in 1997 along the upper slope section and highwall deformation to date has indicated reasonable agreement with the observed mode of failure and displacement monitoring results. The results of detailed analyses of the proposed highwall design have indicated very limited additional deformation, further development of tension cracks is unlikely and large-scale instability is not expected to occur. A total of 40% of additional mining has been completed and ongoing displacement monitoring to date has confirmed very limited additional movement and no further tension crack development.

Jan 1, 2001

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in'progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America.The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

By Orr C. W

Continuing the systematic investigation of the influence of elements on the properties of lead(1). If the effects of additions of copper (up to 0.3%) on Port Pirie lead have now been determined in so far as creep rate is concerned.The results in the present paper contain also a survey of the influence of copper on the micro-structure of lead, a feature which has not appeared in the previous papers of this series. Further, it has now become known that creep is but little related to the more usually determined properties such as hardness and tensile strength. Since, however, these properties are of considerable importance in connection with the fabrication and use of this metal. Brinell hardness determinations have also been made and are here included.It is becoming more and more realised also that to be useful, creep data should refer to stresses of the order of those used in practice. This is due to the fact that as soon as deformation takes place, the properties of the metal are automatically changed. Lead does, of course, creep during industrial use, and probably (in lead chamber construction for example) extensions of the order of 5%...

Jan 1, 1938

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By Eugene L. Grumer

High-expansion foam was applied to the flames of six fuels burning in a 1-foot-diameter tray. The flames of three hydrocarbon fuels were more readily extinguished than the flames of methanol, acetone, or unsymmetrical dimethyl hydrazine. The result is rationalized on the basis that heat transfer from flame to fuel surface is primarily radiative with the hydrocarbons and more largely convective with the nonhydrocarbons. INTRODUCTION Equipment for producing high-expansion foams has been developed by the Bureau of Mines to control coal mine fires.5 Recently such equipment has been redesigned for portability and has now been produced commercially for other fire-fighting applications. In May 1961, a 50-by 50-foot gasoline fire was extinguished within 2 minutes by a trailer-mounted foam unit that produced 12,000 cu.ft./min. of high-expansion (1,000:1) foam.6

Jan 1, 1962

By G. Kelly

A new minerals engineering education programme is being developed in Australia which aims to provide tertiary institutions with a package of educationally sound, high quality courses for undergraduates, postgraduates and professionals. The programme is jointly funded by the Minerals Council of Australia (MCA) and the Department of Education Training and Youth Affairs (DETYA) and brings together academics from a number of leading Australian universities, each developing modules in their particular area of expertise. The University of Queensland (UQ) and the Julius Kruttschnitt Minerals Research Centre(JKMRC) are jointly responsible for modules in several areas including comminution, physical separation and circuit design and optimization. Other modules are being developed by the University of South Australia (with the Sir Ian Wark Centre), Curtin University and Murdoch University. The major challenge of the programme is to provide a high standard of education that is accessible to students who may be located at several different institutions and some of whom maybe a long distance from the primary course leader. Rather than taking existing course material and putting it ‘on the web’, the programme aims to improve on past teaching practice through creative pedagogy and the development of interactive multimedia learning resources. Communications technology is used in an unobtrusive way, and the World Wide Web is used to create a flexible, user-friendly learning environment rather than to facilitate delivery of content. This paper describes the instructional design template currently being used and results of early implementation trials with groups of local and remote students.

Jan 1, 2003

For many years the scrubbing of roaster gas carrying sulphur dioxide has been carried out at the plant of the Electrolytic Zinc Co. of Australasia Ltd. at Risdon, Tasmania, using long horizontal tubes. in which the gas stream crossed a shower of water. In order to provide for increased roaster capacity, it was evident that additional gas scrubbing capacity would be required to prevent pollution of the atmosphere.This provided an opportunity to review the whole operation of gas scrubbing and an investigation was initiated to determine the characteristics of a counter-current type of scrubber. It was hoped that a change to this type of scrubbing would also reduce the sulphur dioxide concentration of the gas delivered to the atmosphere to a negligible amount. This, paper outlines results obtained from an experimental tower which was operated under a wide range of conditions, the packing height, gas flow, water flow, water temperature, and concentration of S02 in inlet gas being varied independently. A description is given of the leading features and operating characteristics of the plant units, which are designed on the basis of the experimental results. Operation of the new scrubbing system commenced on October 5th, 1948.THE PROBLEMThe gas which is handled carries S02 which may vary in concentration from 2% to 5%, and reaches the scrubbing system at a temperature of approximately 180 deg. C. An appreciable amount of suspended material accompanies the gas which has passed the cyclone system.

Jan 1, 1949