Search Documents

By S. Haapala

El presente artículo describe la geología general, formaciones, plegamientos y fracturación, geología económica, mineralogía y la mineralización (alteración, zoneamiento, controles de mineralización) de la mina Colquijirca.

Nov 1, 1954

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By A. J. Mcintosh

PRICE changes in competing fuels in the last three decades have reflected the changes in the consuming habits of the people of the United States. Prior to World War 11 the importance of fuel oil and fuel gas increased almost constantly while the relative importance of both bituminous and anthracite coal decreased. During this same prewar period coal prices increased to a much greater extent than oil prices. In fact, in many years, oil prices declined and in most cases are now no higher than they were back in 1925-26. During the war natural economic trends were entirely upset because of the tremendous petroleum requirements of the Army and Navy. Under these conditions many industrial plants were converted to the use of coal and the new installations in home heating and industrial plants of all kinds which might have used oil were practically eliminated. Although petroleum prices were rigidly controlled by OPA coal prices increased several times during the war. An over-all statement as to the rela-

Jan 1, 1947

In August, 1975, North Broken Hill Limited announced that an intersection of 37.3 m of high grade lead-silver-zinc mineralisation, assaying 26.2 per cent Pb, 495 g/tonne Ag and 21.2 per cent Zn had been obtained at its Mine at Broken Hill, 520 m north-east of its No. 3 Shaft and slightly below the No. 36 level (1581 m). Subsequent drilling confirmed the presence of the extension of the Broken Hill Orebody on the north-western side of the Globe Vauxhall Retrograde Shear Zone and defined 1.8 million tonnes of high grade mineralisation. The area containing this mineralisation was subsequently named the Fitzpatrick Area in tribute to the late Mr. W.E. Fitzpatrick a former Member of the the Board and Manager of the Ccnpany's Broken Hill operations. This paper describes in brief the exploration programme leading up to the discovery, the general geology of the area and the proposed future exploration progranme for further extensions of the orebody within the mining leases of North Broken Hill Limited.

Jan 1, 1983

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By Paul G. Mahoney

The original Radum aggregate plant, built by Henry Kaiser in 1931, is the oldest of the nearly 200 individual operations established by the Kaiser companies. Since that time it has been producing aggregate products primarily for the San Francisco Bay Area. Currently, and for many years, this plant has been listed as the Nation's No. One aggregate producer. Early this year a new $10,000,000 facility went on line replacing the old plant. Construction of the facilities was performed under the direction of Kaiser Engineers construction management teams. The existing plant continued to operate without interruption during the entire construction period.

Jan 1, 1970

By S. P. Kinney

Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. An example of the result of inefficient gas-solid contact in the shaft of a blast furnace is shown by the curves in Figure 1.

Jan 1, 1930

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By Magda Moreira Pinto

Durante a fabricação do aço as grandes siderúrgicas possuem usinas térmicas integradas aos seus processos industriais. Uma operação bastante comum na indústria siderúrgica é a geração de vapor, normalmente utilizado para a produção de trabalho mecânico em turbinas (vapor superaquecido) ou em processos de aquecimento, nos quais se emprega o vapor saturado. Estes vapores de processos também podem ser utilizados na geração de energia elétrica. Para isto, foi importante assegurar a qualidade da água e do vapor de baixa pressão (VBP) enviado para Termelétrica. Foi com este intuito que a TKCSA se preocupou em padronizar o (VBP) gerado na Caldeira Auxiliar da área de Utilidades e Caldeiras da Aciaria. O desafio era transformar o (VBP) na mesma qualidade do vapor produzido nas caldeiras recuperadoras de calor (HRSG). O procedimento adotado foi á modificação no tratamento químico, a instalação de uma monitoração química contínua e eficiente para assegurar os parâmetros químicos dentro da especificação técnica recomendada pelo EPRI - Electric Power Research Institute, Inc. Com este tratamento foi controlada as dosagens químicas, a operação da caldeira e a geração dos efluentes líquidos para o tratamento químico ambiental. Contudo foi possível tornar um mecanismo dinâmico e econômico para a empresa viabilizando a utilização do vapor na termelétrica.

Jul 31, 2018

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974

By S. Budirsky

J.B. Gwiazda's article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point O travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex '85, Katowice, Poland, pp. 73 -83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4600 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (la in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the afore- mentioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda's opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf -Forschungshefle, 1984, NO. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1988

By John Gittins

Lots 11 and 12, Range IX, Calumet island, are underlain by a Grenville metamorphic complex into which sills of tourmaline granite pegmatite have been injected. The pegmatite has an average mode-potash feldspar 65 per cent, sodic plagicdase 10 to 20 per cent, quartz 5 to 20 per cent, tourmaline 10 to 15 per cent, accessory minerals < 5 per cent; it is unzoned except for a narrow border zone. Some of the feldspar has been replaced by calcite. Microcline has been ?partially replaced by sodic plagioclase. Three varieties of tourmaline are present (black, blue, and green) and spectrographic analysis suggests progressive compositional changes during its crystallization. The presence of U- and Th-bearing minerals in the pegmatite prompted the Quebec Nickel Cor,porat10n, Ltd., to explore the possibility of developing the pegmatite but it does not appear that this is economically possible at the ? present time. Tt\e Grenville metamorphic complex consists of recrystallized limestones and calcsilicate rocks of the albite-epidoteamphibolite facies and the amphibolite facies, which were derived from sedimentary rocks. Several of these are dis-equilibrium assemblages, and retrograde metamorphism has probably formed biotite and epidote from hornblende. The schistosity of the gneisses dips steeply eastward. Numerous strike faults are roughly parallel to the schistosity and one of the pegmatite sills is bounded by such a fault, dipping at 60 ° with about one foot of fault breccia. The general structure of the map-area seems to be an asymmetrical syncline ?overturned to the west. The emplacement of the pegmatite is associated with a period of folding, metamorphism, and igneous intrusion.

Jan 1, 1956

By Rodrigo Jerez

This paper describes a Mixed Integer Linear Programming model that was developed for planning the coal operations at Mountain Coals, Inc., in Kentucky. The model incorporates the use of stockpiles as practiced and allows the operator to find the least cost combination of raw coal feeds, washing densities and blending to produce the different quality coals as required by the coal contracts.

Jan 1, 1984

Ok Tedi Mining Limited has recently completed the first phase of a trial to compare the performance of D26B Krebs cyclones in different configurations to the new Warman 650 mm CAVEX cyclones. From 1992, rougher flotation feed size has increased from the target d80 grind size of 150 ¦m with increasing SAG mill throughput. At high SAG mill throughput, operators have difficulty maintaining the target cyclone feed pressure and must increase the cyclone feed density, thus resulting in a coarsening of the cyclone split. Warman International have developed the CAVEX high capacity cyclone. The new CAVEX cyclones, when compared to the Krebs units appear to:produce a measurable increase in volumetric flow for the same pressure drop; maintain or decrease the proportion of coarse particles reporting to overflow; and lower the overflow density. In all plant trials to-date, the CAVEX cyclones appear to be superior to the standard Ok Tedi Krebs cyclones. Further testwork is planned to evaluate modified Krebs cyclones (with recent design improvements) against the CAVEX cyclones.

Jan 1, 2000

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By Winmill T. F.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) The conclusions reached in this paper may be summarized briefly as follows: (1) The method of estimating moisture in coal by determining the loss in weight of a sample heated to 105°-110° Cent, in an air-bath for an hour is untrustworthy, the results so obtained being too low. (2) Dried coal has a very considerable power of absorbing moisture, and a sample, after being dried, must be protected instantly if it is to remain free from moisture. (3) A fairly accurate estimation may be made by heating the coal in a current of dry air at 105° to 110° Cent., and collecting the moisture evolved. (4) In cases in which it is proposed to use the dried coal for any further experiments, the drying must be done in the absence of oxygen, and this can be done simply and quickly by the vacuum method now described

Dec 1, 1916

Careful monitoring of the position of the cave front is essential for well-managed block cave mining. Seismic monitoring systems yield 3-D information about the location of fracturing ahead of the cave. However, because the a seismic gap between cave surface and seismogenic zone is of unknown extent, the cluster of micro-seismicity can only yield an upper bound for the cave height. The large velocity contrast between the fractured rock in the aseismic gap and the broken loose material within the cave can be used by an inversion procedure to find a few simple geometric parameters (such as height of the top of the cave) if a simple 3-D shape?for example a paraboloid?is assumed for the cave. Ray-tracing must be used as the large velocity contrasts cause seismic waves to bend around the cave, but the inversion takes the form of a minimization problem in only a few dimensions and so the computational time is feasible. This technique has been successfully tested on realistic synthetic data.

Jan 1, 2007

By G. Reed Marchant

The control systems engineer is often faced with the problem of designing tests or experiments where the cost of obtaining information is expensive. This is true in aerospace as well as in process industries. In these situations the details of test design should be carefully evaluated before any test is executed so that the maximum amount of information is obtained for the effort expended. In recent years there has been a steady trend towards increased automation, In the process industries this has resulted in extensive review of process variables and, instrumentation techniques, development of more accurate system mathematical models, and extensive investments in complex control system as well as completely automated plants. When planning and developing these systems, where each measure of a process variable is usually expensive, it behooves the design engineer to give considerable thought to the details of test design before instrumentation is procured and installed so that the maximum amount of information can be obtained for the expense incurred.

Jan 1, 1968

By B. J. Dotson, P. N. McCreery, R. L. Slobod, James W. Spurlock

A core sample porosity-check program is described. A number of laboratories participated in the investigation. which comprised measuring the porosities of ten selected natural and synthetic core samples. Each laboratory employed its own method (or methods) of measurement. These included Boyle&apos;s Law, water-saturation. and organic liquid-saturation methods. Brief descriptions of each method employed are given. In general, the measured values of porosity were in reasonably good agreement. The average deviation of porosity from the mean or average values for the group of samples was ±0.5 porosity per cent. The results of these measurements are compiled and presented in graphical form. INTRODUCTION The total hulk volume of a porous sample is derived from the sum of two volumes, the void or pore volume and the solid* or grain volume. The porosity fraction of the sample ia defined as the ratio of the void volume to the bulk volume. Multiplication of this ratio by 100 converts it to per cent porosity. Distinction is made here between total porosity and effective porosity. The former includes all void space, both interconnected and isolated, while the latter includes only those voids which are interconnected. This investigation deals only with the effective porosity.* Numerous cases had been noticed in which there appeared to be appreciable discrepancies in the results of porosity determinations on core samples. Differences of as much as 10 to 15 porosity per cent had been reported from different sources

Jan 1, 1951

By P. N. McCreery, R. L. Slobod, B. J. Dotson, James W. Spurlock

A core sample porosity-check program is described. A number of laboratories participated in the investigation. which comprised measuring the porosities of ten selected natural and synthetic core samples. Each laboratory employed its own method (or methods) of measurement. These included Boyle&apos;s Law, water-saturation. and organic liquid-saturation methods. Brief descriptions of each method employed are given. In general, the measured values of porosity were in reasonably good agreement. The average deviation of porosity from the mean or average values for the group of samples was ±0.5 porosity per cent. The results of these measurements are compiled and presented in graphical form. INTRODUCTION The total hulk volume of a porous sample is derived from the sum of two volumes, the void or pore volume and the solid* or grain volume. The porosity fraction of the sample ia defined as the ratio of the void volume to the bulk volume. Multiplication of this ratio by 100 converts it to per cent porosity. Distinction is made here between total porosity and effective porosity. The former includes all void space, both interconnected and isolated, while the latter includes only those voids which are interconnected. This investigation deals only with the effective porosity.* Numerous cases had been noticed in which there appeared to be appreciable discrepancies in the results of porosity determinations on core samples. Differences of as much as 10 to 15 porosity per cent had been reported from different sources

Jan 1, 1951