Search Documents

By Oliver Bowles

Enormous quantities of limestone are used for metallurgical purposes. Approximately 23 million tons were so used in the United States in 1925 chiefly for smelting iron ores in the blast furnace. Smaller amounts are used in basic open-hearth steel manufacture, and in smelting lead, copper and antimony ores. Most limestone producers lave little knowledge of the way in which their stone is used in metallurgy. Maximum tolerances of silica, alumina, sulphur and possibly magnesium; and minimum content of calcium carbonate may be arbitrarily fixed for the guidance of the producer, but aside from these requirements little information is available to producers on the manner in which their stone is used, the office it performs in smelting, or the effects of impurities. More complete [wledge] of utilization would enable limestone operators to solve their production problems more intelligently.

Jan 1, 1927

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

By W. G. Davenport

Flash smelting is used. mainly for making molten Cu-rich matte* from fine Cu-Fe-S** flotation concentrates. It blows dried concentrate particles into a hot fumace, surrounds them with 01-rich gas and allows them to react. The results are: (a) partial oxidation of Fe and S from the concentrate (b) generation of heat (c) melting of the oxidized particles to form molten Cu-rich matte, ~65% Cu and Cu-barren slag, ~1 % Cu. The melted particles fall to the hearth of the flash furnace where they fonn matte and slag layers, The matte is tapped from the furnace and oxidation-converted to metallic copper. The slag is skimmed, treated for Cu recovery then stockpiled or sold. Figures 1.1 and 1.2 show industrial flash furnaces and the position of flash smelting in the coppermaking flowsheet. ,Fig. 1.3 shows the locations of flash furnaces around the world.

Jan 1, 2001

By Herty, C. H.

One of the numerous requirements of many grades of present- day steel is that the steel shall be free from non-metallic inclusions. These inclusions may be composed of oxides, sulphides, complex oxy- sulphides, and nitrides, which enter the steel with the furnace charge, result from sulphur absorption from the furnace gases, or are formed in the steel during the deoxidation process. Although few' data are available which indicate in any quantitative manner the specific effects of inclusions in steel, there is a large mass of circumstantial evidence which points to the advisability of producing steel free from these impurities for many purposes. At the present time there is a growing feeling among metallurgists that non-metallic inclusions should be divided into two distinct types: (I) those readily visible under the microscope at ordinary magnifications; and (2) those in colloidal suspension or in solid solution. Both types are profoundly influenced by the character of the charge, the manipulation of the furnace slag, and the method of deoxidation. The work described in this bulletin deals primarily with inclusions visible under the microscope at ordinary magnifications, but the steels made by the various methods of deoxidation are being used LO study certain effects which may be ascribed to the second classification, named above. This latter work will be the subject of further bulletins on the effect of deoxidation practice on the physical properties of the steels involved.

Jan 1, 1957

The Colorado portion of the Rio Grande rift is clearly defined physiographically from the south in the San Luis valley northward to the latitude of Leadville where sediments of the Dry Union Formation (Tweto, 1961) accumulated within the subsiding rift zone. To the north of Leadville is a system of faults active in the late Tertiary, including the Mosquito fault that offset a portion of the Climax mineralization (Wallace et al., 1968). Tweto (197B) describes remnants of Dry Union Formation against the Mosquito fault north of Dillon in the Blue River valley, so it is apparent that the rift and associated sediments extended well to the north of Leadville. Kelley (1952, 1954, 1956) and Chapin (1971) have noted in New Mexico that the Rio Grande rift is a series of en echelon basins, offset to the east, with constrictions connecting them (Fig. 1). In Colorado the structural basins are offset to the west. The net effect of all the rift zone basins in New Mexico and Colorado is an arcuate pattern (Fig. 1) abutting the Colorado Plateau and Sari Juan Volcanic Province on the west. The width of the rift system gradually decreases northward to about Leadville where rift definition is not apparent.

Jan 1, 1987

By L. C. IlsLey

The United States Bureau of Mines has been conducting investigations of electrical equipment curing a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 20, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By R. H. Lien

The Bureau of Mines investigated nitrous oxide (N20) stability when used as a solvent for organic removal from metal powder surfaces. Both supercritical and subcritical conditions were studied. This investigation was prompted by the occurrence of a violent reaction when supercritical N20 was being used to deoil a metal powder grinding waste sample that contained 20 to 25 wt pct cutting oil. Tests were conducted to determine the cause of the reaction and to define stability limits. Test data showed that the waste's oil fraction reacted violently with N20 acting as an oxidizer; the metal powder acted as a promoter to reduce the ignition temperature. Although the data were scattered, this temperature appeared to reach a minimum at a certain pressure (dependent on vessel and sample size). The minimum ignition temperature for a 0.64-g sample in a 72-cm3 vessel was 360° C at 200 psig. As the sample size increased, the ignition temperature decreased. For example, when the sample size was increased to 10 g, a reaction occurred at 240° C and 600 psig. Because of the variability of ignition temperature with pressure and sample size, safe operating conditions were not established. Overall, this research showed that extreme caution should be exercised when using N20 in an organic or organic-metal system.

Jan 1, 2011

By Philip C. Good

Unweathered low-grade calcareous phosphate rock of about 20 percent P205 grade was beneficiated by a procedure in which contained carbonates were decomposed by calcination at about 1,000° C. On quenching the hot calcined rock in water, major impurities passed into a slime phase which was mechanically separated from a coarser concentrate fraction. Phosphate rock of two major types was beneficiated in batch-scale studies yielding concentrates containing 31.3 to 38.5 percent P205 at recoveries ranging from 54.8 to 86.0 percent. The samples were from two major deposits in India. Processing information gained was utilized in extending the work to a continuous-flow system, processing phosphate rock at rates up to 157 kilograms per hour. Superphosphate exceeding 16 percent water-soluble P205 was prepared from concentrate derived from continuous-flow processing.

Jan 1, 1976

By Jorge Olivari Ortega

"El presente texto describe la leyenda de los tesoros de plata de Catalina Huanca, perteneciente al valle de Huancayo. El origen de esta estriba en dos versiones. La primera, indica que es ahijada del conquistador español Francisco Pizarro, quien por razones políticas, decidió apadrinar a la menor y la segunda, que era un alias de Teresa Apoalaya, la hija del curaca Carlos Apoalaya (descendiente de Machu Apo Alaya). Ella habría nacido en Chupaca en 1678 y asumiría el curacazgo en 1698. Catalina Huanca murió casi a los noventa años de edad, durante el gobierno del virrey Diego Fernández de Córdova (1621-1628) y fue enterrrada con grandes cantidades de plata. "

Jan 1, 2017

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By G. W. Birge

Carbonizing properties of the principal coal beds of Butler County, Pa., are described in this report by the Bureau of Mines. Eight samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Clarion, and Brookville beds, were carbonized at 900° C. by the Bureau of Mines-American Gas Association (BM-AGA) method. Butler County coals rank as high-volatile A bituminous and are generally characterized by high sulfur content compared with Appalachian coals used for industrial coking. If cleaned, the Brookville and one sample of Upper Freeport coal would be acceptable as the major component of metallurgical coking blends. The other Butler County coals tested would be unsuitable for this purpose because of either excessive sulfur or poor coking properties.

Jan 1, 1962

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By ISEE

Micrometer Crack Response to Vibration and Weather, by Prof. Charles H. Dowding of Northwestern University, adds to Prof. Dowding’s already important contributions to the industry with his “Construction Vibrations” books. This new book reports and interprets important data on crack response that are essential for differentiating the unseen effect of weather on structural cracking from the usually much smaller effect of vibration. In addition, the book contains detailed descriptions of data collection methodology.

Jan 1, 2010

By Luis Herrera, Luis Huamán

La minería peruana se distingue por sus estándares de clase mundial: la innovación es parte de su ADN. En ese contexto, Ferreyros y Caterpillar toman el encargo de participar en el proyecto cuprífero Quellaveco, de Anglo American, con una flota íntegramente autónoma de camiones mineros, los primeros en la historia del país. La búsqueda de la mejora de la seguridad, el incremento de la productividad y la optimización de la utilización de los equipos de acarreo son impulsores clave de la adopción de autonomía.

Sep 30, 2022

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

Oren. F. Bridwell: The President declares there is a quorum. Since the minutes of last year&apos;s meeting arc published in the Proceedings, unless there is objection, we will dispense with the reading of the minutes. There being no objection the minutes will he dispensed with. Is there a report from the Treasurer? Raymond Venous, Chairman, Auditing Committee: I&apos;d like to submit the report for the Secretary-Treasurer for the previous year. Following is the financial report of the Treasurer from May 21, 1964 to May 24, 1965. (Report submitted) May we say, "Cussie," you keep a very, very nice set of hooks. Thank you. Oren F. Bridwell: You have heard the report of the condition of our treasury. We are solvent, at any rate. You have also heard the report of the Auditing Committee. If we might have a motion that the report of the auditing committee he accepted. Moved, seconded and carried. We&apos;ll have a report of the Resolutions Committee. Max A. Robe, Chairman, Resolutions Committee: Ladies and gentlemen, we have four resolutions, which we trust are going to he in the best interests of the Rocky Mountain Coal Mining Institute and the coal industry in general.

Jan 1, 1965

By Edward T. Koch

With the dramatic increase in world demand for basic raw materials, open pit mining is proceeding at an unprecedented rate. A viable demand is the ever tempting Siren&apos;s song for increased production or new facilities. When the Siren&apos;s lure is viewed against the panorama of today&apos;s world economic milieu the concomitant Scylla and Charybdis are seen in the form of high capital cost and high operating cost. If the economic realities of present day open pit mining are to show a proper return on investment, a clear and penetrating eye must be cast upon the area of mine planning. This paper deals with the problem of overburden removal. In almost every open pit mining operation overburden removal is a significant part of the capital cost and operating cost of the total operation. This paper deals with a new and unique method to affect economical overburden removal. Well known to all are the parameters surrounding draglines, shovels, and bucket wheel excavators. All of these machines require a reasonably stable soil to support them and the shovel and bucket wheel excavator require a reasonably stable bank in which to operate. Their reliability, portability and rate of production per dollar of invested capital are good.

Jan 1, 1975

By Henry Mulryan

THE largest and purest known deposit of diatomite is being actively mined and processed 3 ½ miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Manville Products Corporation. The workings FIG. 1-LOCATION OF DIATOMITE DEPOSIT AT LOMPOC. cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoc, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1936