Search Documents

By F. J. Gallagher

Some serious fires have occurred in bituminous-coal mines because of short circuits on direct-current power systems that do not have adequate circuit-breaker protection. The writer's observation of circuit-breaker installations in numerous coal mines leads to the conclusion that many persons am not properly informed as to the true functions, limitations, and operation of circuit breakers. Faulty protection results in fire hazards that endanger lives and property. Proper circuit-breaker protection would greatly minimize or, in many instances, eliminate the hazards; moreover, many operating advantages of proper application of modern circuit breakers would be gained. The purpose of this circular is to show why fire hazards exist in many mines despite the use of circuit breakers and how, the hazards may be overcome. A method is given for determining whether additional circuit-breaker, protection is required for a specific 250/275-volt direct-current distribution system, and, if so, the approximate locations and capacities of the required supplemental breakers.

Jan 1, 1951

By Kung-Lee Wang

This Bureau of Mines study illustrates the economic significance of the Florida phosphate industry to the State and to the Nation. Environmental considerations related to phosphate industry activity are discussed briefly. Based on forecasts of Florida phosphate production in 1975, and using 1972 dollars, regional and national output value, income, and employment created by the phosphate industry were estimated for 1975. State and Federal government tax revenues generated by the phosphate industry, are also measured. Further, the concentrated impact of the phosphate industry on certain Florida areas and on regional industries is examined. Finally, the phosphate industry's importance to the U.S. balance of payments, U.S. agricultural production, and the Frasch sulfur industry is considered, in addition to byproduct fluorine, and potential byproduct uranium from fertilizer manufacturing.

Jan 1, 1974

"Chairman: Dr W. S. RAPSON Rapporteur: Mr J. W. WILSONPapers:Computer applications in rock mechanics by F. H. Deist, E. Georgiadis and J. P. E. Moris Rock mechanics in the design of mine layouts by K. Hodgson and N. G. W. Cook Automated regulation of mine ventilation by P. NiskanenThe rock mechanics papers, because of their complementary nature, were presented in succession and discussion on both followed directly. The paper on automated ventilation control at a mine in Finland was then presented and the session was closed with several contributions to this paper.By and large the papers and discussions which followed in this session showed how a classic tie-up had developed between the use of computing techniques in important fields of mining, and their practical application. In fact, the dis-cussion following the rock mechanics papers showed clearly that without the aid of high-speed digital computers the rate of progress in applied research in deep-level hard-rock mines, would have been severely hindered. Furthermore, it became apparent from the comments made by several contributors that the rock mechanics techniques and computer progress described in Deist's and Cook's papers could be used to provide useful data in the solving of rock mechanics and design problems on mines other than flat dipping deep tabular deposits.The paper by Niskanen, which described an automated ventilation control system at a mine in Finland, showed how effective computers could be in areas where the reversal of mine ventilation occurs due to severe seasonal temperature ranges. Although the system described in the paper could not be introduced easily in complex underground mines, several contributors gave examples of similar ventilation problems that could be solved mechanically,In introducing his paper, Dr Deist said that the purpose of the paper was to give a brief account of some of the programs designed by himself and his co-authors to aid in the solution of rock mechanics problems,The first system presented by Dr Deist was known as MINSIM in the South African mining circles. This system was designed specifically to aid in the solution of rock mechanics problems in the South African gold mining industry. It was particularly designed to handle tabular deposits at great depth but it has been used satisfactorily on a number of occasions to obtain at least approximate solutions in other mining situations. Dr Deist said that the principles embodied in the programs were easily extended and, in fact, there was a project in progress at that time which was aimed to do this. He said that the principles could easily be extended to shallow-depth mining at steep or very steep inclinations."

Jan 1, 2014

By G. E. Warner

This paper presents a review and analysis of a highly stratified Burbank sand waterflooding project in Osage County, Okla. Permeability values in this reservoir range from less than 0.1 md to nearly 3 darcys, and 90 percent of the permeability capacity is contained in approximately 26 percent of the reservoir volume. To date, the project has recovered 103 bbl/flood-acre-ft since waterflood initiation, which represents 50 percent of the total preflood cumulative and 12 percent of the original stock-tank oil in place (OSTOIP). The outstanding feature of this project has been the economical recovery of a sizable quantity of oil at water-oil ratios higher than those normally considered prohibitive. Nearly 70 percent of the recovery to date has been achieved at water-cut values greater than 95 percent. An ultimate waterflood recovery of 138 bbl/flood-acre-ft, or 67 percent of the preflood recovery and 16 percent of the OSTOIP, is predicted. The ultimate primary and secondary recovery will be 302 bbl/acre-ft and approximutely 40 percent of the OSTOIP. The actual performance is compared with the predicted performance by both the Stiles and the Dykstra-Parsons methods, and applicabiliry of these methods to this particular reservoir is evaluated. The performance of this project indicafes highly stratified reservoirs can be successfully and economically waterflooded when either reservoir or economic conditions preclude the use of mechanical and chemical means of mdbility control. Introduction The concept of the stratified reservoir has been used by reservoir engineers for many years to describe the vertical variations in permeability within a reservoir. Numerous techniques have been advanced to predict the expected waterflood performance of the stratified reservoir, and in most cases they prove reasonably accurate. The advisability of undertaking a prospective waterflooding project is determined, based on these predictions. This paper presents a review of a waterflood project in a highly stratified reservoir that normally would be considered a marginal prospect, at best, when evaluated with any prediction technique properly adjusted for reservoir conditions. This kind of project can be successful if the predictions are used to design a waterflooding system capable of economically recovering an oil cut of 1 to 2 percent. Experience gained in the early stages of the project's development was profitably applied in the later development of the entire reservoir and could prove beneficial to other projects with similar reservoir stratification or fracture characteristics. The East Burbank pool waterflooding operations have been developed in three separate stages, each of which has been a separate project: Mid-Burbank Unit, Flood A, and Stanley Waterflood. When referred to collectively, these projects will be called the Composite Project. The Skelly Oil Co.'s Barber lease — the only portion of the pool not included in the three projects — is operated as a separate facility with a cooperative injection-well agreement. It contains less than 80 productive acres and would not significantly affect the over-all performance picture.

Jan 1, 1969

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By K. L. Purdy

Electron spectroscopy for chemical analysis (ESCA) was used to determine the-surface characteristics of products from operating Pb-Zn-Cu concentrators on the New Lead Belt of southeast Missouri and pure galena and sphalerite samples treated-with flotation reagents in concentrations similar to those used in the mills. The emphasis was on the action of surface modifiers such as Na2Cr207, starch, SO2, CuSO4 and NaCN in sphalerite flotation and in the galena-chalcopyrite separation. The objective of the investigation was to monitor the relative oxidation states of the mineral and reagent constituents and correlate these surface concentrations and oxidation states with flotation theory and practice. ESCA was able to follow the action of all the modifiers except NaCN. The existence of PbCrO4 on the surface of galena conditioned with Na2Cr207 was verified. The Pb in the bulk PbS-CuFeS2 scavenger concentrate was found to be significantly more oxidized than the Pb in the bulk PbS-CuFeS2 rougher concentrate. ESCA was found to be most useful for investigating the actions of modifiers rather than collectors due to the large amounts of sulfur and background carbon already present on the mineral surfaces. After calibration for the particular chemical system of interest, ESCA can yield semi-quantitative analyses of the oxidation states of many elements (except hydrogen, and helium) present in the outer 10 to 25 A of a sulfide mineral surface.

Jan 1, 1975

By Xianjun Lyu, Junxiang Wang, Peng Wu, Minjie Lian

"In recent years, the efficient cementation of mine tailings is a new way to manage mine solid wastes. The traditional cement materials have a slow setting time, large dosage and poor cementation strength for fine aggregate such as mine tailings. Therefore, the preparation of new type cementitious materials for the cementation of fine tailings has great potential in the treatment of mine waste solids. The paper mainly focuses on exploring the critical factors affecting the cementing performance of granulated blast furnace slag and its performance in the cementation of fine aggregate. Results indicate that the fineness of slag has a significant effect on its cementitious activity and Portland cement clinker has a better stimulation effect on the cementitious properties of slag than lime. And, anhydrite has a better early stimulation effect on the cementitious properties of alkali-activated slag compared to semi-hydrated gypsum and dihydrate gypsum. According to a series of tests on the cementation of fine iron tailings, the optimal ratio of slag, Portland cement clinker and anhydrite is determined as 60:30:10. Compared with P.O 42.5 ordinary Portland cement, the new slag based cementitious material shows much better cementing performance on fine tailings sample. Under the dosage of 12%, the compressive strength of fine tailings mortar using slag-based cementitious material in 3 curing days is increased to 168% that of using P.O 42.5 ordinary Portland cement, while the compressive strength in 28 days curing period is increased to 194%."

Jan 1, 2018

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908

By X. Gumede

Mud houses are common structures in most South African rural homes closer to the mining operations. Fulltime dwellers in these properties are often the elderly. The mine codes of practice and the South African legislative instruments attempt to define the damage criteria to limit the effect of the blast-induced noise and ground vibrations to different structures. All these assessment criteria are based on the peak particle velocity and noise generated during blasting. The South African safe limit criterion that was adopted was initially derived from the international standards, which were then used as a local guideline. This paper evaluates the currently adopted safe limit criteria used in South Africa for a mud house, currently rated at 6 mm per second and 120 decibels to134 decibels, for blast-induced seismicity and noise, respectively. Further, a study was performed on a residential house near a coal mine (5.26 km) based in Mpumalanga following numerous complaints by the owner, launched at the mine and to the Department of Minerals and Petroleum Resources. The aim of the study was to measure the magnitude of blast-induced triggers experienced at the aggrieved homestead and to establish if there is a likelihood that an irritation or damage may be caused by these triggers. The seismometer was installed at about 2 m from the mudhouse, from 1 July 2022 to 31 of July 2022. Five blast-induced triggers were recorded during the period showing an average of 0.09 mm/s and 121 decibels for blast-induced seismicity and noise, respectively. The results obtained indicated a maximum seismicity of 0.15 mm/s. This seismicity was below the perceptible vibrations obtained from daily home activities such as walking, jumping, and door slamming, which produce 0.8 mm/s, 7.1 mm/s, and 12.7 mm/s, respectively. Seismicity was therefore not likely to have caused any annoyance and or damage. For noise, the results indicated a maximum of 123 decibels and an average of 121 decibels from five events recorded. A literature review suggests that slight damage may occur when airblast frequencies match the natural frequencies of structures at 120 decibels. Based on these results, it can be concluded, therefore, that the noise, rather than seismicity, is more likely to be the cause of damage to the structure assessed. For improvement, a new approach is proposed based on relating the safe limits to the structural and human response.

Dec 15, 2025

By R G. Reddy

The complexity in treating environmentally harmful impurities such as As, Sb, Bi from the base metal matte or metal in the smelting stage are responsible for the high cost of the refining process. The impurity capacities (such as arsenic, antimony and bismuth) of slags were calculated a priori using Reddy-Blander (RB) model. The capacity predictions were for a wide range of matte and slag compositions in copper smelting conditions. The calculated impurities capacities and impurity distribution ratios results are in good agreement with the available experimental and industrial slags data. The a priori knowledge of impurities is useful for reduction of energy consumption and enhanced environmental control in the current and future non-ferrous metal processes.

Aug 21, 2024

By MINE SAFETY BOARD

RECOMMENDATIONS OF THE UNITED STATES BUREAU OF MINES ON CERTAIN QUESTIONS OF SAFETY AS OF FEBRUARY 3 , 1933

Jul 1, 1933

By Jorge Acosta Ale

"El presente texto señala la perspectiva de la producción peruana de cobre para la próxima década y su aporte económico en el Perú a través de un cuadro estadístico donde se observa un incremento de los pórfidos de Cuajone y Cerro verde en los años 70´, skarn de Tintaya en los 80´ y Antamina en el 2001. Así también se revisa el canon minero, regalías mineros y derechos de vigencia. "

Dec 1, 2016

By M. C. Leverett

THE dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the vis-cosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability" to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indi-rectly. However, it is expected that work along lines similar to this present under-taking will help materially in solving these problems. Previous workers in this field have inves-tigated the two-phase systems, water-gas,1 water-oil2 in unconsolidated sands, and water-gas3 in consolidated sands. The ex-tension of the study of the flow of hetero-geneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.2 Correlation and interpretation of data were made by methods analogous to those used in two-phase work. The relative permeability to a phase-the effective permeability divided by the permeability of the system to a homogeneous fluid-was employed through-out in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two inde-pendent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically. The gas fraction was deter-mined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accu-rate numerical results. Reasonable precision and reproducibility were sought.

Jan 1, 1940

By Andrew Hyslop

In our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber-tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys- tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1949

By J. A. C. Fortescue

"Reconnaissance geochemical mapping, based on the chemical analysis of waters, stream, and / or lake sediments had its origin in geochemical prospecting surveys carried out in New Brunswick during the 1950s. More recently, reconnaissance geochemical surveys carried out by government agencies for mineral resource appraisal purposes have been seen as a special case of regional geochemical mapping which is carried out with the aim of describing geochemical patterns f or elements which may he interpreted for mineral resource appraisal, environmental or geological purposes. The interpretation of pal/ ems on regional geochemical maps is based on the concepts of landscape geochemistry, in this paper, the regional approach 10 geochemical mapping is described with reference to an experimental regional geochemical survey which was completed in southwest Ontario during 1981-82. II is concluded, on the basis of data pal/ems for one element only (i.e. arsenic), that the new approach has much potential for solving modern problems in geoscience.""If things don 'I alter they will stay as they are... An old adage.IntroductionDuring the past hundred years topographic, geological, and geophysical maps have been made for all, or nearly all, of Ontario. During the past thirty years these maps have become related as components of what is now called geoscience. Geoscience maps at the regional (i .e. 1 :250,000) scale are often used together to solve general problems in earth science especially in relation to prospecting, or mineral re source appraisal."

Jan 1, 1986

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

By T. Sakaguehi

Some attempts were made to recover and remove of uranium that may be present in refining effluents, mine waste Water, and other waste sources by using microbial biomass. To establish which microorganisms accumulate the most uranium, 135 species of microorganisms (42 bacteria, 26 yeasts, 34 fungi and 33 actinomycetes) were screened. Of these 135 species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stuzeri, Neurospora sitophila, Streptomyces albus and Streptomvces viridochromogenes. In addition to the research on uranium uptake, thorium recovery by using microorganisms was investigated. High abilities were found in Streptomyces levoris and Bacillus subtilis. The selective accumulation of heavy metal ions by various microorganisms has also been examined. Uranyl, mercury and lead ions were readily accumulated by almost all of the species of microorganisms tested. Actinomycetes and fungi differ from many bacteria and most yeasts in their selective accumulation of uranium, and mercury. The basic features of uranium uptake by Streptomyces viridochromogenes, a microorganisms with high uranium-uptake ability, were investigated systematically. Synthesizing these results, we suggested that the accumulation of uranium into these microbial cells is not directly mediated by any metabolic process:, but almost completely dependent upon physicochemical adsorption on the cell components. In addition to this fundamental research, uranium recovery was investigated in immobilized Streptomyces viridochromogenes. These immobilized cells adsorbed, uranium readily and selectively. The immobilized cells recovered uranium almost quantitatively and almost all uranium adsorbed was desorbed with 0.1 N Na2CO3, These results showed that microbial cells are more stable after Immobilization and can be used repeatedly for the process of uranium adsorption-desorption. These results suggested that these microbial cells can be used for the recovery and removal of nuclear fuel elements, such as uranium and thorium, from refining effluents and mine waste water.

Jan 1, 1991

By Junwei Han, Wenhua Li, Wenqing Qin, Fen Jiao, Wei Liu, Jiaqi Xu

"A novel technology was developed to study the process of recycling copper from waste printed circuit boards (WPCBs), which are the main source of metal production in the next decades. The chemical compositions of the WPCBs were investigated. The results indicated that the PCB powder was mainly composed of copper (38.5 wt.%), iron, aluminum, and non-metallic materials. Copper is mainly in the form of Cu and is the most valuable metal for the recycle of WPCBs. The concentrated WPCBs powder, obtained by the mechanical process, were pressed as the anode, which was directly electrolyzed to produce copper. The effects of H2SO4 concentration, Cu2+ concentration, current density, pole pitch, and liquid-to-solid ratio on the voltage, current efficiency, and copper extraction were investigated. The results indicated that the optimum conditions were liquid-to-solid ratio of 30 mL/g, current density of 571 A/m2, sulfuric acid concentration of 180 g/L, 50 g/L of copper ion, polar distance of 3 cm. Under the conditions, a desired current efficiency could be achieved. Meanwhile, about 95.62% Cu was recovered from the WPCBs. The experimental studies also revealed that the purity of copper obtained at the highest current efficiency was higher to 99.98%. Produced copper sheet were characterized by X-ray diffraction (XRD). XRD analysis indicated that the copper was the main phase. INTRODUCTION With the rapid development of electronic industry, more and more waste electronic and electrical equipments (WEEE) are generated every year (Fogarasi et al., 2012; Liang et al., 2013). The production of printed circuit boards (PCBs) is the base of electronic industry, because it is the essential part of all electrical and electronic equipments (Schlummer et al., 2007). As a result, a considerable amount of waste PCBs containing plenty of heavy metals have to be treated. In general, PCBs contain about 28% metals that are abundant non-ferrous metals such as Cu, Pb, and Sn. Printed circuit boards can be considered as a secondary resource for recycling rather than wasting. The contents of gold and silver respectively reach 80 g/t and 3300 g/t, which are much higher than that of primary ores. Copper is the main metal of PCB and its content is as high as 26.8% ( Zhang et al., 2009)."

Jan 1, 2018

By Chester A. Rowland

INTRODUCTION Comminution is generally a feed preparation step for subsequent processing stages; exceptions being when a final product such as aggregates, specification sand, Portland Cement, and similar products is produced. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding -- primary and secondary), natural or manufactured non-metallic media (pebble milling) or manufactured metallic media -- steel rods, steel or iron balls. This chapter will discuss general mill design and the specific design and application of the following types of tumbling grinding mills. [Overflow Rod Mills Figure 1 Peripheral Discharge Rod Mills Figures 2 and 3 Compartment Mills Rod and Ball Figure 6 Ball Figure 6a Pebble Mill Figure 6b Overflow Ball Mills Figure 8 Diaphragm (Grate Discharge) Ball Mills Figure 9] I. GENERAL MILL DESIGN A. Liners The interior surface of grinding mills exposed to grinding media and/or the material being ground are protected from wear and corrosion by rubber, metallic, a combination of rubber and metallic, or non-metallic wear resistant materials. B. Drives Economics at the time of plant design and mill purchase determine the drive to be used. The simplest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinion-shaft by either an air clutch or flexible coupling.

Jan 1, 1982