Search Documents

By M Zengerer

The Basil Cu/Co deposit comprises a 26.5 Mt Inferred Resource of copper and cobalt, grading 0.57?per cent Cu and 0.05 per cent Co. It lies in the Harts Range, Central Australia, within the Riddock Amphibolite of the Irindina Province. Analysis of drilling within the mineralised zone of the deposit determined a spatial association between pyrrhotite with high magnetic susceptibility and chalcopyrite, following a strong magnetic trend as determined from airborne geophysics. A study was commissioned to examine if geophysical inversion could predict the distribution of sulfide mineralisation based on pyrrhotite from drill hole intersections, as well as predicting further mineralisation at depth or in the vicinity of the deposit. Petrophysical and geostatistical analysis of drilling susceptibility and mineralisation provided a basis of property distribution inside the model. This was followed by 3D geological modelling of mineralisation based on domain kriging of drill hole susceptibility sensitivity testing of signal to source depth, and distribution was performed using 3D forward modelling. Stochastic inversion generated alternative 3D geological models, which were tested for behaviour and adherence to observed drilling data and geostatistical limitations using GeoModeller software. Predicted mineralisation distribution was compared with conventional geostatistical modelling and found to be in agreement in planar behaviour but exhibiting possibly isoclinally folded trends, with reliability increasing closer to the surface. Predictions of mineralisation at greater depth and beneath weaker anomalies were more diffuse due to small model cell size having limited influence on the signal at depth.The Blackbush uranium deposit comprises a 64.5 Mt Inferred Resource, grading 230 ppm U in the Pirie Basin south of Whyalla, South Australia. It directly overlies the radiogenic Samphire Granite and is considered a tertiary unconformity deposit. Sensitivity modelling was performed using high-resolution ground gravity to see if a deposit signature could be detected using gravity. This required 3D implicit modelling of the geology and mineralisation from drill hole data and characterisation of an associated physical property model using domain kriging in GeoModeller. Density models relied on exploiting an observed relationship between logged density and measured uranium oxide percentage. The residual gravity response of the background geology model identified the location of the uranium deposit. Stochastic inversion of the litho/property 3D model has refined the known distribution of uranium from drilling and provided structural insights into the deposit.These projects have become excellent case studies for exploiting the relationship between mineralisation and potential fields and for testing the applicability of using domain kriging of properties determined from drilling to build robust 3D geological models for stochastic geophysical inversion, leading to robust methods for exploration targeting and mineral deposit prediction.CITATION:Zengerer, M, 2014. Use of geostatistically-constrained potential field inversion and downhole drilling to predict distribution of sulfide and uranium mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By F. Boudreault, M. J. Scobie, J. Szymanski, C. Hendricks

The development of new stoping methods and more effective control over dilution, recovery and fragmentation depends on improved accuracy in blasthole drilling. The mechanisms and factors which control accuracy are poorly understood. Canadian blasthole stoping and the practices adopted for monitoring and controlling drilling accuracy are reviewed. The techniques and problems associated with blashole set-up and trajectory surveying are discussed. Four new blasthole trajectory survey systems are evaluated on the basis of their performance in recent underground trials. Conclusions are drawn as to the technological developments required so that more precise control over drilling accuracy can be achieved.

Jan 12, 1992

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By E. L. Fosse, W. S. Wright

"INTRODUCTION Preliminary and detailed exploratory examinations of iron and copper ores on Prince of Wales Island have been conducted by the Bureau of Mines from early in 1942 until the end of 1944. Among these investigations was that of the Jumbo magnetite deposit, which was visited by Stephen P. Holt, an engineer of the Bureau of Mines, during a preliminary examination of the Copper Mountain and Jumbo properties September 15 to 18, 1943, During the months of June, July, and August 1944, a more detailed examination, which consisted essentially of mapping and sampling, was made by the authors working in conjunction with George C. Kennedy of the Geological Survey, Geological, topographical, and dip-needle contour maps were made of the area, and 97 channel samples were cut.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes sam¬ples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is made to R. D. Stewart, Territorial Commissioner of Mines and former general manager, and to Duncan Campbell, Ketchikan, Alaska, former mine superintendent of the Jumbo mine. Acknowledgment is also due to George C. Kennedy of the Federal Geological Survey for extending cooperative assistance in topographical mapping, dip-needle surveying, and geological study of the deposits. Further acknowledgment is made to C. Travis Anderson, chief, Rolla Division, Metallurgical Branch, and other members of that division for conducting beneficiation tests on Jumbo Basin ores."

Oct 1, 1946

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By W. L. Price

Since first introduced in the United States in 1964, rail mounted bucket wheel stacker-reclaimers have gained wide acceptance by users. The coal burning power plant group has adopted this new storage tool most quickly. The actual history is traced in this area in some detail. Installations in phosphate and steel mill ore storage and a listing of present users are included.

Jan 1, 1969

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005

By T. M. Romslo

"INTRODUCTION This report presents factual data obtained by the Bureau of Mines in the course of an investigation of the Antler mine in the Cedar Valley mining district, Mohave County, Ariz.The Antler property was first examined by Thomas L. Chapman, mining engineer, Bureau of Mines, on December 18, 1943, and January 28, 1944. In June 1945, A. H. Wadsworth, Jr., and R. L. Griggs, geologists, Federal Geo¬logical Survey, examined the Antler mine and several other mines in the district. Both Chapman and Wadsworth recommended diamond drilling of the Antler property to determine the character and extent of ore deposition.In October 1946, the surface and underground workings were surveyed by George Huseman, Mining engineer, and T. M. Romslo, project engineer. The following month Eldred. D. Wilson, geologist of the Arizona Bureau of Mines, assisted by the project engineer, mapped the geology. Subsequently trails were built to drilling sites and diamond drilling started January 16, 1947. The project was completed April 25, 1947.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and takes beneficiation tests."

Mar 1, 1948

By Robert J. Evans

The monorail bridge conveyor (MBC) is a prototype continuous face haulage system that was surface tested and evaluated by the Bureau of Mines. The MBC consists of a series of cascading belt bridge conveyors suspended from roof-supported monorail track. Tests were conducted to determine MBC haulage capability, maneuverability, power consumption, and reliability using rigid and chain-suspended monorail track installations. Subsequent modifications to improve operation and reliability made during surface testing are described. Mining plans were devised to show potential MBC installations for room-and-pillar, longwall development, and shortwall mining sections. Compatibility tests were conducted with the Bureau&apos;s prototype hopper-feeder, to provide additional surge capacity and lump-breaking capability. Results from the surface test program, along with modifications to improve system operation and reliability, indicate that the MBC has the potential to perform success- fully in an in-mine trial.

Jan 1, 1987

By M. D. Everell

Le Centre de Recherches minérales (CRM), qui est un organisme de recherche appliquée du ministère de l&apos;Energie et des Ressources du Québec, a été créé en 1969, dans le but de procurer un support scientifique et technique à l&apos;industrie dans le domaine des mines et de la métallurgie. Pour atteindre ses objectifs, le CRM met à la disposition de l&apos;industrie un personnel spécialisé et compétent dont une quarantaine d&apos;ingénieurs et de scientifiques. Etant donné la nature même de l&apos;industrie minérale, ce personnel est très versé dans l&apos;étude des problèmes diversifiés des domaines de la technologie minière, du traitement des minerais, de la métallurgie extractive et de l&apos;analyse minérale. Ce Centre de recherches met également à la disposition de l&apos;industrie une usine-pilote permettant de reproduire les résultats du laboratoire au moyen d&apos;un appareillage de type industriel, d&apos;obtenir des échantillons en quantité suffisante pour une exploration du marché et de familiariser du personnel avec les opérations normales de l&apos;industrie. Certaines de ses contributions récentes au développement de l&apos;industrie minérale du Québec seront présentées.

Jan 1, 1985

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954

By P. K. Chatterjee

Computer aided design and inter active graphics have been well established in the electronics, automotive and mechanical engineering industries. The use of such aids in underground mine design and planning, however, has been noticeably absent. The large expense involved in the research and development of CAD and graphics systems and their highly specialized techniques have rendered investment in these areas difficult to justify. Optimum mine planning involves an interactive procedure of evaluation of several alternative plans. Generally the development of each mine plan of a given operation can take many man-months. This time constraint on planning precludes any comparative analysis and evaluation of alternatives, thereby introducing the possibility of unrealized gains. This paper outlines the development of a computer aided mine design program utilizing interactive graphics for the design, simulation and scheduling of underground coal mines. The program developed examines exploratory borehole information and produces a structured database of the sampled data. This database is utilized to generate seam sections and different mine layouts. A simulation of mine extraction and production levels and a schedule of proposed alternatives are then performed.

Jan 1, 1984

By Kenneth Williams

Cargas a granel, incluindo finos de minério de ferro, devem ser embarcadas de acordo com as diretrizes acordadas entre os membros da Organização Marítima Internacional (IMO). Uma medida de segurança crítica é o Limite de Umidade Transportável (TML), exigido para cargas do Grupo A (cargas que têm tendência à liquefação). Diversos acidentes com navios envolvendo finos de minério de ferro da India, cuja causa suspeita-se ser a liquefação da carga, trouxeram à atenção o tema do TML de finos de minério de ferro. Um trabalho extenso de pesquisa foi desenvolvido pelos principais produtores de minério de ferro da Austrália e do Brasil para dar suporte à IMO no desenvolvimento de normas para o embarque desse tipo de material. Com essa finalidade, mineradoras patrocinaram o projeto AMIRA P1097, que foi conduzido pela TUNRA Bulk Solids (TBS) e o Centre for Bulk Solids and Particulate Technology (CBSPT), CSIRO e a Universidade de Auckland, com a gestão do projeto sendo feita pela Creative Process Innovation, a fim de estabelecer uma abordagem modificada de testes de TML específica para finos de minério de ferro. Esse estudo deu suporte aos resultados dos testes e conclusões do Technical Working Group do IMO, que publicou suas conclusões e descobertas em Setembro de 2013.

Aug 16, 2017

By R. E. Perry

To develop new or improved flotation methods for beneficiating low-grade red iron ores, the Bureau made many bench scale and continuous anionic flotation tests on ferruginous sandstones and calcareous iron ores from the north-eastern part of the Birmingham, Ala., iron district. The ores contained about 21 to 36 percent iron, a to 11 percent lime, and 22 to 64 percent silica. Production of iron concentrates containing 48 to 52 percent iron was technically feasible in batch tests, and the iron recoveries ranged from 85 to 92 percent. In continuous tests 49 to 51 percent iron products were obtained with 80 to 90 percent recovery.

Jan 1, 1962

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By E. O. Strahl

In the search for economic mineral deposits, the need for efficient mineral or chemical assays is of prime importance. Costly analytical methods and long delays in obtaining assay results severely limit the effectiveness of an exploration program. The assay problem becomes acute once a potential ore body is located and large numbers of samples are generated in close interval drilling programs. In order to avoid the delays and high costs of extensive assays, the exploration geologist or mining engineer is likely to be required to curtail his drilling program, composite samples, or restrict the required analyses to a limited number of critical elements. As a result, the definition of the potential ore body may be less than needed for final economic evaluation. The assay requirements for bauxite exploration usually involve a considerable number of total elemental and empirical analysis. Since the Bayer process for extracting alumina from bauxite involves the selective dissolution and reaction of specific minerals from the bauxite, a direct chemical analysis for elemental composition yields only a portion of the data required to effectively describe the potential economic value of ore body or deposit. To fully characterize the economic value of a bauxite requires digestion, mud separation and mud settling tests under conditions approximating a commercial Bayer plant. A close approximation of the process behavior of a bauxite also can be calculated from a combination of the chemical and mineralogical analyses. By determining the elemental chemistry, mineralogy, and Bayer plant processing characteristics of a few samples of a given bauxite, correlations can be derived that permit defining a bauxite in terms of a given set of process conditions.

Jan 1, 1977