Search Documents

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

By Franklin D. Cooper

Three model dwelling units were redesigned to achieve specific levels of noise reduction above that provided by conventional construction. Using 1968 prices, the added costs of materials and installation were found to range from $500 to $5,000 depending upon the size of the dwelling unit and the degree of insulation. The potential aggregate expenditures for sound insulation materials are projected to reach $617 million in 1975, including about $408 mil- lion for the mineral-based materials, in 1968 constant dollars. The report includes a brief review of the mechanics and effects of sound.

Jan 1, 1970

By Inkap Choi

Asbestos is a broad term embracing a number of fibrous silicate minerals. These minerals look extremely fragile, yet their fibers have a tensile strength equal to that of piano wire. Chrysotile asbestos is the only mineral that can be woven into cloth, and its fibrous structure is, if anything, even more amazing than its remarkable ability to withstand heat. Because of its unique physical properties asbestos has achieved great industrial importance, and more than 3,000 current uses are known, ranging from use in the kitchen to use in space missiles. Because their minuscule fibers are eminently respirable, asbestos minerals have also found their way into the lungs of humans, where they apparently produce serious biological effects such as asbestosis and lung cancers. 1, 2,3 Because of both their usefulness and their hazardous properties, these minerals have attracted a good deal of attention from research workers during recent years. For example, the surface properties of asbestos minerals have been studied by many investigators. 4, 5, 6, 7, 8, 9 However, even for the important mineral chrysotile, the literature data are more or less conflicting. Pundsack4 measured a PZC (point of zero charge) of 10.1; Martinez and Zucker5 measured 11.8; Chwastiak reports 10.8-11.0; and Raddick measured three sepa-rate apparent PZCls at about pH 8.3, 10.0 and 10.9. More recently Trivedi8 reports 10.11. Naumann and Dresher9 have studied surface charge enhancement of chrysotile by metal ions, and describe how the mineral reacts with contaminantions. In the present paper, the mode of dissolution of magnesium and hydroxyl ion from asbestos minerals placed in water was studied by kinetic experiments involving rate at which these items leave the minerals. Also, some study was made of interaction between dissolved species.

Jan 1, 1972

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

"En 1953, se habilita la nueva planta de flotación de cobre en Paragsha, donde el funcionamiento de las soleras tipo Lorain y la producción del mineral pirita lograron buenos resultados. Empero las nuevas condiciones de proceso, limitaron su funcionamiento y costo. Por tal motivo, el objetivo del trabajo se basa en la construcción de una solera de mayor rendimiento y menor costo, modificando su diseño al de una honda contínua. El primer juego de este diseño fue instalado en el molino de cobre Nº 1, sin aún obtener el dato final sobre su rendimiento. Posteriormente se consideró la solera AMSCO, dado que el diseño fue más eficiente y el costo final por tonelada fue menor. Sin embargo, se encontró que el contorno del valle era muy cerrado y las bolas N°4 se alojaban de modo ajustado, formando una solera muy gruesa. En consecuencia, se construyó otro diseño denominada ""Solera de onda abierta contínua"", el cual fue instalado en el molino de cobre N°7, donde la capacidad de molienda es igual de óptima y los costos son menores. Así, se pensó que la solera de una sola honda, es mejor que la de onda contínua puesto que este diseño tiene una sola honda en el centro de cada plancha de la solera. Luego, se diseño un tercer diseño, donde el promedio de vida era mejor. Por ello, de los tres diseños a seleccionar -la solera Lorain con 10 hondas, la solera de una honda con 20 hondas y la solera de honda continua de 30 hondas -, la última demostró ser la más eficiente. De otro lado, se probaron otros diseños de honda contínua con distintas aleaciones como el ""Nihard"", cuyo promedio de vida es entre 14 y15 meses aproximadamente, con el tonelaje actual de aproximadamente 270 000. Concluyendo que la experiencia anterior con solerasNihard en molinos a rodillos de 4 pies de diámetro, el impacto es mayor, obteniéndose en quebrantamiento de soleras a 3/4 grosor, pero que pese a esto, resulta ser superior a cualquier otra solera usada actualmente y en eñ que Paragsha esté 100% con soleras de molinos Nihard, a excepción de las rejillas dada su fragilidad. "

Jul 20, 1957

By S. Narra

The importance of bio-products production is enhanced with the abundance and renewability of ligno- cellulosic biomass in comparison to the depleting fossil fuels especially in producing environment friendly energy. Lignin is obtained as a sludge residue from the pulp and paper industries as well as from the bio- ethanol /bio-gas production plants. Lignin is a renewable fuel with a high heating value equivalent to anthracite coal, low ash content and hydrophobic properties. The extracted lignin in paper and pulp mills is usually burnt at the mill directly to cover the energy production costs of the mill. The efficient utilization of lignin can reduce the percentage of lignin sludge used for energy production in comparison to the present situation. Presently the lignin is burnt /incinerated as sludge with minimum of 30 to 50 % moisture content. This high moisture content reduces the energy efficiency and simultaneously utilizes more amount of lignin sludge in producing the required energy. This paper explains a possibility of integrating sludge-pelleting techniques in paper and pulp mills. The integrated sludge-pelleting techniques would lead to an optimal utilization of lignin for energy and would simultaneously save the lignin resource for material utilization. The sludge pelleting process solves also the problem of handling, storage and explosion risks of lignin when compared to the present situation.

Sep 1, 2012

By Jack L. Henry

The ternary system A14C3-AIN-Al203 has been examined to determine compositions which may display desirable high-temperature refractory properties. Powder methods were employed in the synthesis of all test compositions. Forming and sintering behavior was examined and hot-pressing parameters were measured. Several properties were studied for each composition of interest in the system. The properties included hydrolysis rate in moist air, elevated temperature oxidation rate, density, softening point, tensile strength, and rupture strength. In most cases equilibrium was not achieved, and the data are representative of a nonequilibrium system. Approximately 16 separate phases have been observed in the system. Forming behavior and selected properties of five compositions of interest were compared with those of aluminum oxide and aluminum nitride. None of the compositions compared favorably. Oxidation and vaporization appear to be serious drawbacks to the use of these compositions at elevated temperatures.

Jan 1, 1969

By R. D. Stewart

Abstract. Induced fluorescent sorting is a means of beneficiating an ore by selective labeling with a reagent combination which fluoresces when activated by ultraviolet light The reagent combination normally consists of a surface active compound and a fluorescent dye. The surfactant adheres selectively to a specific surface and carries the dye with it. Upon activation with ultraviolet light, the labeled pieces, in the size range 1.27 cm to 20 cm (0.5 to 8 in.), are detected during free fall by photosensitive cells and ejected by water jets. Either ore or gangue may be labeled.

Jan 1, 1980

By Rudy E. Barrientos Ontón

El presente texto describe los datos geopolíticos, reforma económica y poltíca nacional de competencia y regulación minera de uno de los principales líderes en la industria minera, Australia. Dicho país es similar al Perú -en tanto alberga recursos naturales como minerales e hidrocarburos, cuyos ingresos, producto de la extracción, son fuente para la realización de actividades conducentes al desarrollo sostenible.

Sep 1, 2014

By F. A. Schinner

The present study has investigated the leachability of cadmium sulfide minerals by Thiobacillus ferrooxidans and the electrochemical reactions involved in the process. Using a cyclic voltammetric technic and carbon-paste-CdS electrodes, it was found that the bio-oxidation of semiconductor cadmium sulfide minerals consisted of a number of intermediate electrochemical reactions. The overall reaction was found to be controlled by solid state diffusion as suggested by the chrono-amperometric and chrono-potentiometric measurements. The activation energy of solid state diffusion was determined by the Sand's method to be AE=24.3 kJ. A generalized mechanism was proposed for the bacterial oxidation of cadmium sulfide by T. ferrooxidan and an explanation given for the importance of high redox potential of leach solution versus the decomposition potential of the sulfide mineral. Furthermore, the effects of n-type or p-type character of CdS substrates relative to their bioleachability was discussed.

Jan 1, 1993

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By Ernie M. Crist, Laurentiu Nastac, Frank Spadafora

"This paper describes the modeling techniques and the experimental and computer results for two casting processes that are under development and optimization. These processes are described as follows:1) Electromagnetic stirring (EMS) during casting of Ti-6Al-4V round ingots using the plasma arc cold hearth melting (PAM) process: The purpose of EMS is to establish a singlemelt PAM process capable of consistently producing as-cast ingots without helium porosity and also having no need for surface conditioning prior to secondary processing.. The modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure.2) Casting of Ti-6Al-4V slabs using the single-melt PAM process: The purpose of slab casting is to improve yield by eliminating an intermediate blooming step for converting round ingots to slabs. The modeling approach is based on the numerical solution of fluid flow and heat transfer equations. The effects of pouring and mold temperatures on the pool and temperature profiles were studied. Also, the torch effects (such as the torch standoff and its traversing path) on the pool and temperature profiles were investigated and the best-case scenario was used in the experiments. Evaluation results at RMI Titanium Company showed that the plates made from the slabs met the mechanical properties and microstructure requirements.Acknowledgment. This work was conducted by the National Center for Excellence in Metalworking Technology (NCEMT) operated by Concurrent Technologies Corporation (CTC) under contract No. N00014-00-C-0544 to the US. Navy as part of the US. Navy Manufacturing Technology Program. Dr. K. b. Yu from RMI and my colleagues from CTC are acknowledged for their comments on this work."

Jan 1, 2004

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By R. R. Beebe

Marcona Corporation produces about 3.5 million long tons of iron ore pellets annually on its two travelling grate pelletizing machines at San Nicolas, Peru. During 1969, these pellets will be shipped to customers in four marketing areas--Japan, the United States, Europe, and South America. All of these sales are on the open market, and product quality is a major concern. Typical chemical, structural, and quality test results for Marcona pellets are given in Table 1. [ ]

Jan 1, 1969

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By E. S. Forbus

A process for producing reductive bleach in-situ in kaolin slurries has been developed. The bleach is formed by mixing an iron sponge powder (-325M) with slurry treated with SO2. The process has been successfully demonstrated in production, and applied to several grades. The color, brightness, and viscosity of the bleached product is equivalent to or better than that of product bleached with commercial sodium hydrosulfite . The tested products can be bleached at a cost, which is 38-54% of those associated with the use of commercial bleach.

Jan 1, 1993

By P. A. Wasson

The investigation described in this publication was conducted by the Bureau of Mines to determine the effectiveness of the anionic silica flotation method on goethitic iron-bearing materials from the Cuyuna Range, Minn. Samples used in this investigation were a composite of drill core from 13 holes, and 3 samples from lean ore stockpiles. These samples are believed to be typical of the mineralization occurring in an area with a potential reserve of several million tans of submarginal iron ore. Results from batch tests showed that the iron-bearing minerals could be effectively concentrated by flotation removal of the siliceous gangue. The drill hole composite yielded laboratory flotation concentrates from locked tests containing 56.8 percent Fe and 6.1 percent silica, with an accompanying iron unit recovery of 94.2 percent. Concentrates containing 52.4 to 53.7 percent Fe also were produced from the lean ore stockpile materials; corresponging iron recoveries ranged from 71 to 79 percent in the batch tests, with the possibility remaining for additional recovery of iron from the middlings.

Jan 1, 1963