Search Documents

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll' have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to in- crease. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining

Jan 1, 1981

By Joseph R. Hatch

Previous studies of the Thompson and Temperly ore bodies show alteration aureoles in the Middle Ordovician host-rock limestones, dolomites and shales extending laterally as much as 60m from the ore. Thickness, texture, carbonate and clay mineralogy, major-, minor-, and trace-element contents; and carbonate carbon and carbonate oxygen Isotope compositions of the host rocks all have been significantly altered by hydrothermal processes. Organic geochemical analyses of samples from the basal 8-cm-thick carbonaceous shale bed and immediately overlying limestone bed of the Quimbys Mill Member of the Platteville Formation, collected from within the ore, the alteration aureole, and the unaltered country rock show: 1) solution of carbonates and residual concentration of organic matter, 2) decreases in the volatile (Si) and pyrolytic (S2) hydrocarbon yields In samples of the basal shale from within the ore, 3) decreases in the relative amounts of the lower molecular weight (<nC25) saturated hydrocarbons in samples from the ore, and 4) no changes in either the organic carbon isotope composition or the Rock-Eval or biomarker thermal maturation Indicators. In light of the 125-170°C depositional temperatures documented for the early marmatitic sphalerltes in these deposits by fluid Inclusion studies, the lack of thermal alteration of the organic matter suggests a relatively short mineralization episode, a conclusion supported by the relatively simple sphalerite band stratigraphy. The decreases in the volatile and pyrolytic hydrocarbon yields for shale samples from the ore supports a model for mineral deposition which obtains sulfide through reaction of brine sulfate and indigenous organic matter.

Jan 1, 2013

By P. A. Geusebroek, N. A. Duke

Abstract - The Lupin mine, located in the central Slave province just east of the western boundary of Nunavut Territory, is a world-class example of a Neoarchean-aged banded iron formation (BIF)-hosted lode-gold deposit. At the minesite the gold-mineralized Lupin BIF, separating stratigraphically underlying psammitic wacke and overlying argillaceous turbidite sequences, delineates the Lupin dome, a hammerhead-shaped F2/F3 interference fold structure occurring at the greenschist to amphibolite facies metamorphic transition within the thermal aureole of the Contwoyto batholith. Detailed paragenetic relationships indicate that peak thermal metamorphism coincided with the switch from regional D2 compression to rapid D3 unroofing of the Neoarchean orogenic infrastructure. Gold initially precipitated with pyrrhotite, replacing amphibolitic BIF at the apex of the Lupin deformation zone, separating the east and west lobes of the Contwoyto batholith. Over the course of associated prograde/retrograde metasomatic overprints, gold was further remobilized during garnet and loellingite/arsenopyrite growth in chlorite-altered selvages of late-forming ladder quartz veins. A metamorphic model of ore genesis, with gold being scavenged and transported by metamorphic fluid that was shed and structurally trapped at the amphibolite recrystallization front, is favored over the previously proposed syngenetic and exogenic models of gold concentration that have tended to polarize genetic interpretations to date.

Jan 1, 2004

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Suresh K. Bhatt

Although overall worker productivity for U.S. underground coal mines is available, productivity by mining method and seam thickness is not. Mining technology has gone through dramatic changes in the past decade, and the industry has experienced a lack of accurate productivity Figures addressing these changes. This information is of great interest in planning for future mining systems as thick and shallow coal seams currently being mined are depleted and exploitation of thinner, deeper, and better quality seams is considered to partially meet the requirements of the 1990 Clean Air Act Amendments. In a cooperative program, the U.S. Bureau of Mines obtained raw mine level production and related data from U.S. Energy Information Administration for 1989 and 1990 and performed the needed statistical analysis. Base criteria, parameters, and salient results of the mine productivity analysis are presented in this report.

Jan 1, 1994

By P. H. Tumialán

Dado que la veta El farallón del batolito de la Costa en Huarochirí, Lima, fue alimentada por flujos hidrotermales horizontales, se prevee que la mineralización de los flujos horizontales forman parte final del flujo de ascenso vertical, que en los yacimientos anteriores no se pudo hallar. En esta perspectiva, para la veta señalada, el zoneamiento con eje horizontal en sentido contrario al flujo mineralizante, es de plata, cobre, plomo, zinc y oro. En consecuencia, el concepto genético y el zonamiento hallado se convertirá en una guía para la exploración geológica de estos yacimientos, donde no solo hay flujos horizontales hidrotermales en rocas volcánicas estudiadas en Julcani por U. Petersen, sino también en rocas sedimentarias e intrusivos.

Oct 14, 1980

By L. S. Darken

IT has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernst1 in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and Fuoss2 with results which have recently been confirmed experimentally by Harped and Nuttall.3 This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author 4.6 who pointed out4 that "for a system of more than two components it is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepticism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley11 in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion 0f acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 1050°C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1948

By Arvid E. Anderson, Frank K. Cameron

The weathering of copper-bearing ores with the formation of a water soluble salt and the recovery of the metal by leaching and evaporation precipitation, are processes long known, which have at various times been utilized with more or less commercial success. It is commonly assumed that the technical principles involved are quite simple and their application to a particular case easy. If these assumptions were true, we should anticipate a long list of uniformly successful leaching operations, which is not the case, and one would be justified only in calling attention to either unique or peculiar features of any particular enterprise; whereas, in studying the problems of the recovery of copper from the old workings of the Ohio Copper Co. in the light of available descriptions of other leaching projects, we have not found the assistance hoped for to guide us to the best realization of our own opportunities. It appears desirable, therefore, to call attention to these guiding principles, together with a description of the facts of accomplishment. Justification lies in the fact that the leaching and precipitation of copper at the Ohio Copper Co. mine in Bingham Canyon, Utah, is successful. This success is measured by an average monthly production of 600,000 Ib. of copper at an average operating cost, to date, of 3.85 cents per pound at the company&apos;s workings, or 6.32 cents per pound after paying shipping and smelter charges on the finished copper. A total of 17,076,099 Ib. of copper had been shipped to the smelter from the beginning of operations, August, 1922, to April 1, 1925. Probably these results can be bettered with further study and realization of the factors involved and the devising of methods of meeting them. It is now an assured fact that the enterprise will have a relatively long and continuously profitable life and that its reserves will not, nor cannot, be suddenly and permanently depleted. It is particularly noteworthy that the financing of this enterprise has been entirely from its earnings. The few hundred dollars necessary for the first experiments and production were obtained by the sale of used, and no longer needed, equipment from a mill belonging to the company; and all funds since required throughout the growth and development of the enterprise, from a few troughs with a production of 2000

Jan 1, 1926

The weathering profile, in arid terrains, is commonly capped by different kinds of hardened crust, whose formation is related to recent or former climates. One may distinguish silcretes, calcretes and the ferruginous (or ferro-aluminous) laterites. the present keynote address mostly deals with the lateritic regolith and, moreover, the influence it has on mineral exploration. The lateritic regolith, also called "cuirasse", is a result of a massive accumulation of Fe (and/or Al) oxides on top of weathering profiles developed during former, probably seasonal humid, climatic episodes, and whose preservation depends on the characteristics of later climates. The total thickness of such weathering profiles commonly exceeds 50 m, with an almost complete substitution of the rock forming minerals by secondary minerals as kaolinite and Fe-Al oxi- hydroxides (hematite, goethite, boehmite, gibbsite). Such an alteration of the primary minerals assemblage is of course accompanied by significant changes of the chemical composition, as concerns major and trace elements. The latter are distributed amongst the main secondary mineral phases or trapped in some primary resistant minerals, but may also be leached, totally or partially. Gold is also affected by lateritic weathering, as shown for instance by morphoscopic and geochemical studies of gold grains collected in the different horizons of the profile, which indicates some dissolution followed by reprecipitation.

Jan 1, 1988

By Donald R. Rathburn, Jung K. Mok

An historical review and a survey of current practice in the application of fine dry grinding in the iron ore industry are given. Both closed and open-circuit applications are reviewed, and the advantages, disadvantages, and process considerations for these two systems are discussed. The ground ore temperature rise, and the cool-ing of ground ore and mill ventilation are also discussed, along with the agglomerating characteristics of dry ground ore. Screening during the production of high-grade lump ore for blast-furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date. Others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. In almost all cases some grinding is required prior to pelletizing. Most of these ores occur in the weathered state which may result in difficulty in the thickening and/or filtering stages when ground in a wet system. The resulting filter cake would probably require partial drying to provide a product suitable for the subsequent balling operation; however the partial drying and subsequent material-handling steps often produce random agglomeration. Normally, these agglomerates will cause problems in the green ball formation process. Thus dry grinding has developed as a solution to this problem. Most of the dry iron ore grinding installations utilizing the standard-type rod or ball mill are grinding high-grade natural ores that do not require beneficiation. Although power consumed per ton of final product is 120% or greater in dry grinding as compared with wet grinding, the additional power required for dewatering and handling a wet ground product can easily exceed the initial power savings. Dry grinding of raw feed and clinker has been practiced in the cement industry for many decades but its major application to the iron ore industry has taken place only within the past ten years. The successful application of dry grinding to iron ore has required the solution of several unique design and operating problems. The purpose of this paper is to review recent developments in fine dry grinding of iron ore for pelletizing and to discuss the various designs and operating parameters involved.

Jan 1, 1971

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By Robert E. Cuthbertson

IT is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson3 by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be confined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. BRIEF HISTORY OF REAGENT PRACTICE AT CLIMAX Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium, cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 1920, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Never theless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1944

By H. C. Goodrich

AT THE Utah Copper mine, steam shovels were first used, in 1906, for the removal of overburden, and in June, 1907 for the mining of ore. Prior to 1907, the ore came from underground development work and from stoping. The use of the steam shovel gradually increased until 1914; since then all material, both overburden and ore, has been loaded by power shovels operating on the various benches of the mine. During FIG. 1.-SCENE OF UTAH COPPER MINE BEFORE OPEN-PIT MINING WAS BEGUN. these 19 years, there has been a great improvement in open-pit mining; largely in the use of equipment having greater capacity and dependableness. The history of the development of mechanical shovels and related equipment, as affecting the Utah Copper Co., would be interesting and would justify considerable space; but of greater interest at this time is the operation of the equipment now in use. The Utah Copper mine is in a great deposit of copper-bearing monzonite, which occurs as a prominent headland of the Oquirrh range of

Jan 9, 1925

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By L. Bratek, K. Jaworek, M. Czaplicka

Methods for arsenic compound removal from aqueous solutions include processes such as: coagulation, adsorption, membrane techniques, electrochemical and biotechnology techniques. Advanced oxidation using both UV radiation and strong oxidizing agents such as ozone and hydrogen peroxide may also decompose these compounds. It is known that effluents from metallurgical processes contain inorganic arsenic compounds in addition to the organic compounds such as: dimethylarsinic acid and phenylarsonic acid. This paper presents the conditions that lead to the formation of deposits containing mainly arsenic, such as pH, the wavelength of the radiation and the type of oxidant, for this type of effluent.

Jan 1, 2014

By A. Kaufman

More than 3 trillion gal of water are used annually by the mineral industry. Of this, approximately 21/2 trillion gal are recirculated, the rest constituting intake water. The major users are natural gas processing plants and phosphate rock, sand and gravel, and iron ore producers. Water was used by the mineral industry for mining (6%), processing (64%), cooling and condensing (27%), and miscellaneous uses such as boiler feed and sanitary purposes (3%). Whereas total water use is dependent on the quantity of material processed and on the particular process requirements of an industry, recirculation is dependent on processing, as well as cooling and condensing requirements, quality of new water intake, and the necessity for treating new and discharged water. Consumed water, on the other hand, is dependent on the quantity of water recirculated, and temperature and humidity in the area. Based on this analysis, an increase in water use by the mineral industry of 21/2 times by 1985 is forecast. Wster intake, however, will only rise 62%, because of a substantial increase in recirculation. In one report of a special series concerning the water resources of the United States, the Senate Select Committee on National Water Resources, 87th Congress, estimated that water demand would double by 1980 and triple by 2000.&apos; In view of the possible water deficiencies that might result from such expanded usage and the need for research guidance, the Bureau of Mines organized and carried out a statistical canvass of water use in the mineral industry for calendar year 1962. The data used in this paper, unless otherwise noted, are derived from that canvass.&apos; The efforts in this paper are devoted toward summarization of the canvass and analysis of the data. SOME DEFINITIONS Intake: Water introduced from an external source for the first time into a given mine or plant regardless of quality. Intake water is also called new water, water withdrawn, or makeup water. Fresh Water: Water suitable for cooking and drinking. Saline Water: Water containing more than 1000 parts per million of dissolved solids. Contaminated Water: Water not suitable for domestic use, but excluding saline water. Recirculated Water: Water reused to conserve intake water. Solutions that are recycled primarily because of fixed metallurgical practices, such as copper leaching solutions containing sulfuric acid, are excluded. Gross Water Used: Recirculated water plus intake water. Also called total water used. Consumed Water: Water that is lost by evaporation, as well as water lost in product. Seepage and transferred water are not considered consumed. The use of either intake or recirculated water may result in consumption. However, because of difficulties in measuring consulmption, consumed water is defined as the residual between intake and water discharged from the mine or plant. Mineral Industry: For the purposes of this paper, mineral industry includes all metal and nonmetal surface and underground mines and their associated processing plants, as well as custom mills, coal washing plants and associated mines, petroleum and natural gas well drillers, natural gas processing plants, and secondary recovery operations. WATER USE IN THE MINERAL INDUSTRY Water used by the mineral industry constitutes a relatively minor fraction of the water withdrawn by all users. Data compiled by the U.S. Geological Survey in 1960 indicate that water withdrawals, exclusive of that used to generate hydropower, approximate 99 trillion gal annually.3 Our data indicate that water withdrawals by the mineral industry comprise only 1% of this total, or 2% of the water withdrawn by industrial users. Use by Industry: Water used by various mineral industries is shown in Table I. The table indicates that close to one-half of the gross water used by the mineral industry in 1962 was used by natural gas processing plants, followed by sand and gravel, phosphate rock, and iron ore producers. The largest aggregate users of water are also the largest users per dollar of product. For example, Fig. 1 shows that the natural gas processing and phosphate rock industries are very large users of water per dollar of product. Their recirculation per

Jan 1, 1968

Since the 1950&apos;s drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980&apos;s. Also in the early 1980&apos;s a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980&apos;s. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988