Search Documents

By Charles Zdazinsky

"The Multiple Seed Waveform (MSW) blast vibration model, a type of waveform superpositionmodeling developed by Orica Inc., uses vibration data that is collected from a signature hole blast tocharacterize the ground’s seismic properties and determines the ground resonant frequency andfrequency range that is well supported by the ground. Additionally, the MSW model uses thisvibration data as input parameters to predict the resultant dominant frequency of a production blast. This information may in turn be used in conjunction with precise timing control to target theoptimum dominant frequency which promotes ground control."

Jan 1, 2016

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By Richard S. Della Valle

Sandstone and shale samples from the Morrison (Late Jurassic) and Dakota formations (Cretaceous) from northwestern New Mexico have been analyzed for the major elements Na, K, Fe and the trace elements Sc, Cr, Co, Rb, Sb, Cs, Ba, Hf, Ta, Th, iJ and the rare earth elements (REE) in whole rock and clay sized fractions by instrumental and delayed neutron activation analysis. The clay sized fraction clearly shows enrichment patterns and halo effects ; whereas, the whole rock fraction does not. Important elemental dispersion halos associated with uranium in sedimentary environments include the REE, Hf, and Sb. The distribution of these halos are due to a combination of complexation, chelation and the orignal paleoenvironments.

Jan 1, 1984

By M. E. Fine

IN the apparatus for measuring internal friction shown in fig. 1, a modification of that described by Kê,1,2 the parasitic energy loss or background is equivalent to a Q-1 of approximately 4x10-5. This low value of background was obtained by using a jeweler's collet of appropriate size for the upper support, eliminating lateral motion without immersing the bob in oil, and designing the bob to reduce air resistance. The pendulum is supported on the frame through a snug fitting, sliding rotary joint (fig. I-B). A slight twist of the top imparts essentially pure torsional motion to the pendulum. No evidence of energy loss in the sliding joint has been observed. In the bob (E) steel balls are used in the torsion arm, and the bottom is filled with lead giving a total weight of 94 g. A lighter bob may be used for small diameter specimens. Another bob was a solid disc with provision for adding discs to change the frequency. The oscillating image of the filament is recorded on a revolving drum camera (fig. 1-3) driven by a synchronous motor. This allows use of frequencies higher than can be measured visually on a glass scale. Samples varying in diameter from 0.020 to 0.075 in. have been measured, the frequencies have ranged from 1 to 12 cps, and the maximum strain varied from 0.5 to 10x10-5. With appropriate modification the sample may be placed in a thermostat. The apparatus may also be used to measure the shear modulus. In the examples of measurement given in table I the internal friction of Permendur and the 46.8 Ni-Fe alloy are due, for the most part, to magneto-mechanical hysteresis8 (elastic hysteresis accompanying stress-induced magnetostriction) which depends on strain amplitude and increases with annealing. The internal friction of most materials decreases with annealing. References IT. S. K6: Physics Review (1947) 71, 533. 2 T. S. Kê: Transactions AIME (1948) 176, 448; Metals Technology (June 1948) TP 23703. 3 R. Becker and W. Döring: Ferromagnetismus. 365 (1939). J. Springer.

Jan 1, 1951

By Craig R. Barrett, Alan J. Ardell, Oleg D. Sherby

It is shown that the apparent activation energy for creep of pure poly crystalline metals increases with increasing temperature in the temperature range 0.5 to 1.0 of the absolute melting temperature. This increase is probably associated with the influence 0-f the elastic modulus on the creep rate. By accounting for the variation of Young&apos;s nodulus with temperature, the true activation energies for creep of pure cadmium and aluminuvl are shown to be equal to the activation energies for self-diffusion in these metals, within experimental error, at all temperatures above 0.5T,. New creep parameters are proposed for cmrelation of steady-state creep rate and time-to-rupture data. These are respectively, where u is the creep stress, E is Young&apos;s rrodulus, i,is the steady-state creep mte, t, is the time -to-rupture, and D is the self-diffusion coefficient [equal to Do exp (-QSd/RT)] . It has been established experimentally1 and theoreticallyZm4 that high-temperature creep of poly-crystalline pure metals is a thermally activated process and may be represented by the general expression where <, is the steady-state creep rate, A is a constant dependent on the internal structure of the material, f is some function of the applied stress (0) and test temperature (T), and D is the self-diffusion coefficient. If D is separated into its temperature-dependent and independent portions, then it is possible to rewrite Eq. [I] as where Qsd is the activation energy for self-diffusion. Assuming a simple Arrhenius-type relationship between creep rate and temperature at a given constant stress, the apparent activation energy for creep, Q,, is given by the expression It is obvious that if is not a function of temperature It has been shown that the steady-state creep rate for pure polycrystalline metals1 can be represented by where S is a constant, L is the grain diameter, E is the isotropic polycrystalline (unrelaxed) elastic modulus, and n is a constant equal to approximately 5 over a wide range of stress. The apparent activation energy for creep calculated from this expression at constant grain size and stress is given by

Jan 1, 1964

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

By Esaki M, Nishimura K

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By L Kempenaers, T van der Maten, U König, M G. C Zoontjes

Improving liquid blending operations in production plants is of paramount importance in many industries like mining, oils, petrochemicals and food. For accurate blending of different types of process streams, like homogeneous, heterogeneous, cold or hot streams, it is essential that the composition can be accurately monitored in real time. Advances in energy dispersive X-ray fluorescence (EDXRF) technology offers the possibility to apply XRF for online elemental analysis. In this paper we discuss an online EDXRF analyser for accurate blending control in many industries.EDXRF has the advantage that multiple elements can be measured simultaneously over a wide concentration range of wt per cent down to a few mg/kg, for elements between sodium (Na) and americium (Am) in the periodic table. To reach the desired accuracy and precision in an online XRF analyser, it is important to bring a representative and homogeneous sample of the process flow into the optical path of the analyser. The combination of a laminar flow cell design and advanced EDXRF technology leads to low detection limits and high performance. The obtained precision and accuracy allows for much tighter process control. In this paper we present two examples of industrial applications.CITATION:Zoontjes, M G C, van der Maten, T, Kempenaers, L and König, U, 2017. Online X-ray fluorescence spectrometer for accurate monitoring and improving blending sharpness in liquid production processes, in Proceedings Eighth World Conference on Sampling and Blending , pp 235–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Chromite ore is an indispensable raw material in the manufacture of ferro-chrome and charge-chrome, which are used for the production of stainless and other alloy steels. The demand for chromite ore is ever increasing because of increasing consumption of these steels. Keeping this in view, Tata Steel is keen to recover values from fines and wastes, and also to produce value added products from their captive chromite mines and its processing plants.Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In many places, in India and abroad, mined non-marketable off-grade and low grade chromite ores are upgraded by using either simple classification techniques like screw classification, hydrosizing, hydrocycloning or conventional gravity concentration processes such as Heavy media separation, Jigging, Spiraling, Tabling etc.At Tata Steel, the ferruginous type ores are treated in Chrome Ore Beneficiation (COB) Plant that comprises: a crushing and grinding circuit; a classification circuit using hydrocyclones; and a beneficiation circuit using 4 stage spirals in the coarse circuit (-0.5+0.1 mm) and 3 stage spirals & tables in the fine circuit (-0.1+0.038 mm). In this process, 3 types of tailings are being generated and together analyses about 17 % Cr2O3, which is high. From the present operation the chromite recovery is around 70% and could not produce coarse concentrates (+0.5 mm size). Whereas the siliceous type ore is treated in the Lumpy Ore Processing (LOP) plant, consisting of crushing-washing & classification-hand sorting operations, to produce marketable grade lumpy ore and –10 mm de-slimed fines. These fines are intermittently treated in the COB plant. The higher silica content (greater than 1%) and low Cr/Fe ratio (less than 2.8) are the problems with these concentrates."

Jan 1, 2003

By N. Mungan, F. W. Smith, J. L. Thompson

Adsorption of polymers and transport, rheology and oil recovery efficiency of their solutions were studied in the laboratory to evaluate the use of polymers in waterflood-ing. While a tenfold mobility reduction was obtained with polymer concentrations as low as 0.05 per cent by weight, the mobility reduction depended on the type of polymer, molecular weight, salinity and pH of water, crude oil and capillary properties of the porous media. Choice of a suitable polymer and a workable concentration will have to be tailored for each application. Little reduction in the residual oil saturation can be expected from polymer flooding. Improvement in the volumetric sweep efficiency is possible hut the extent of the improvement can best be evaluated by properly designed field testing. Some aspects of the field use of polymer floods are discussed. INTRODUCTION Waterflooding is a simple, inexpensive secondary recovery method and is being used widely. Innumerable laboratory studies have been made to unravel the fundamentals of the displacement of oil by water and to find the ways of most efficient oil recovery. These studies and a great many field case histories have revealed that the prime cause of poor oil recovery is the inefficient and incomplete sweep of reservoir volume by the injected water. Sweep efficiency is affected by many factors of which the mobility ratio is an important one. Mobility ratio M is defined here as the ratio of water to oil mobilities: M = (k»/y,r)/(k,JJJJ........(1) In Eq. I, the permeabilities are the effective permeabilities and depend on fluid saturations and, hence, change during the different depletion stages in a flood. A wide practice is to use the effective water permeability at residual oil saturation and the effective oil permeability at interstitial water saturation in Eq. 1. If the mobility ratio is greater than one, the mobility ratio is unfavorable and water, being more mobile than oil, would finger through the oil zone resulting in poor oil recovery efficiency. If the mobility ratio is favorable (one or less) the displacement of oil by water occurs more or less in a pistonlike fashion. In some waterfloods. the mobility ratio is unfavorable and any additives by which the mobility of water can be decreased would favor more efficient oil recovery. The thing to bear in mind, however, is whether or not the improvement in oil recovery is sufficient to more than pay out the cost of the additives needed. For example, materials like sugars, alcohols and glycerine reduce water mobility by thickening the water, but the cost of material requirement precludes any field application. For an additive to be useful in water-flooding, it must bring about a large reduction in water mobility at low concentrations; it must be adsorbed only negligibly; and it must not completely plug up the formation. Some synthetic organic polymers have shown promise of meeting these requirements and have been used in the field.&apos;-W owever, no in-depth studies of the rheological, adsorption and oil displacement characteristics of polymer solutions have been reported. The present work is a study of these properties. EXPERIMENTAL In this work, concentrations are given on a weight per volume basis; 0.5 per cent concentration means 0.5 gm of polymer is dissolved in enough water (or NaCl solution) to make 100 ml. A bactericide, usually 0.1 to 0.2 per cent by volume of 38 per cent formaldehyde solution, was used in the polymer solutions. The NaCl solution was 30,000 ppm. Some properties of the polymers studied are given in Table I. Physical properties of all cores used are in Table 2. Flow behavior of polymer solutions was studied by three consecutive flow tests in cores. First, water (or brine) was injected at constant rate of about 1 ft/D to obtain the water mobility. Then, filtered polymer solution (prepared in water or brine) was flowed through the core. Since the rate was constant, increase in the pressure drop across the core reflects decrease in the mobility. Finally, the core was flooded with water (or brine) to study recovery of mobility. The Alundum cores which were used in

Jan 1, 1967

By Ernest Ph. Hérivel

The mine and treatment plant of the Teziutlan, unit of the Mexican Corporation, S. A., are located at Aire Libre, in the District of Teziutlan, near the northwest edge of the State of Pueblo, Republic of Mexico. The property is leased from the Teziutlan Copper Co. The town of Teziutlan is the terminus of a branch railroad starting from Oriental Junction or the Mexico-Jalapa-Veracruz narrow-gage system of the National Railways of Mexico. A branch line 18 km in length from Teziutlan to Aire Libre belongs to the Teziutlan Copper Co. and is leased and operated in conjunction with the mine.

Jan 1, 1933

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth&apos;s surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By K Ehrig, C Lower, V Liebezeit, M Smith, E Macmillan

"Minerals, minerals, minerals. Elements occur in the earth as minerals. If local physical, chemical and structural conditions are conducive to concentrating these minerals to sufficiently high abundances in the earth’s crust, a mineral deposit will form. If technology is available to extract metals from the minerals economically, then you have a mineral resource that will be mined and processed. Determining which minerals are present and quantifying their abundances, textural characteristics (grain size and shape) and how they are intergrown with each other is the realm of the mineralogist. Geologists use this mineralogical data to understand how the mineral deposit formed, how to find high-grade zones within the deposit and where to find other mineral deposits. Metallurgists use this data to design, operate and optimise processing facilities to extract metals from the minerals. The types, quantity and precision/resolution of the mineralogical data required by geologists and metallurgists are different, but are not mutually exclusive of each other. Fortunately, measurement technology is available that is relatively rapid, high volume and low cost, thus enabling ore and gangue mineral characterisation at a historically unprecedented scale of a mineral resource.CITATION:Ehrig, K, Liebezeit, V, Smith, M, Macmillan, E and Lower, C, 2014. Geologists and the value chain – how material characterisation by modern mineralogy can optimise design and operation of processing facilities, in Proceedings Ninth International Mining Geology Conference 2014, pp 5–14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.&apos; I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker&apos;s hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By I Lumsdaine

QNI Pty Ltd operates the Yabulu Refinery located 25 kilometres north of Townsville, North Queensland. The plant treats nickel laterite ores sourced from the Philippines, Indonesia and New Caledonia. The cobalt head grade and overall recovery expectations for the 2001/2002 financial year are 0.161 per cent and 53.8 per cent respectively. Cobalt is a valuable byproduct derived from the nickel refining operation which utilises the Caron Process. Any increases in cobalt recovery that are achieved from the existing relatively low level provide significant improvements to the bottom line of the operation. Towards the end of 2000, a project was undertaken to characterise cobalt losses with the sole purpose of improving cobalt recoveries using a variety of analysis techniques. The Time-of- Flight Secondary Ion Mass Spectrometry (TOF-SIMS û University of South Australia) method was used to verify the presence of surface bearing cobalt species, originating from either co-precipitation or adsorption mechanisms. Cross-section examinations were also performed using Scanning Electron Micrscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDXS). These techniques indicated the presence of high cobalt concentrations (in the order of several per cent) within a select number of roasted and leached ore particles. The phenomenon of cobalt losses due to incomplete leaching within specific ore particles was not widely documented within the Refinery prior to these studies. In order to quantify losses via this mechanism, Mineral Liberation Analysis (MLA û JKTech Centre) was also performed on key samples. This paper serves to document a systematic approach in determining the source of significant valuable mineral losses in an established, operating plant. It discusses the use of a variety of analytical techniques, which have been adapted for the minerals processing industry, but are strongly relevant for plant investigations in the hydrometallurgical industry.

Jan 1, 2002

By Kenneth Williams

Economic drives dictate the exploitation of formerly less attractive ore bodies located close to or even beneath the water table. These ores can cause handling problems and expensive downtime of processing equipment due to their increased adhesive characteristics and are colloquially termed as “wet and sticky” ores. In order to gain a better understanding of the causes of poor handleability, experimental test methods for wall and inter-particle adhesion within bulk solids samples were developed and validated. The results confirmed that adhesion of bulk solid to equipment surfaces is mainly governed by capillary pressure. It can therefore be described using the Young-Laplace equation, which implies that adhesion is primarily dependent on the interfacial water between bulk material and the adhesion partner. Accordingly, the governing material parameters of adhesion are its capillarity and permeability, as these two characterize water transport to or from the interface of the adhesion partners. Furthermore a threshold for the classification of a material as wet and sticky based on the measurements of adhesion has been proposed.

Aug 17, 2017

By Paul E. Rosten

This paper describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Company to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Company operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and Western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes .each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously. (1) (2)(3) Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and furnished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate-kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1977

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000