Search Documents

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By R. L. Rough

The Bureau of Mines analyzed rotary-coring-operations data to compare mud and air as coring mediums, and to compare core recoveries, penetration rates, and cost data for the respective mediums as part of an investigation of the susceptibility to secondary-recovery techniques of petroleum reservoirs in Ohio, Pennsylvania, and West Virginia. This report describes the rotary-diamond coring equipment and operations employed while coring 20 wells--10 cored using mud, and 10 cored using air. Data relevant to the draw works, rotary-table power, drill pipe, drill collars, core barrel, core head, mud pumps, or air compressors are tabulated. Average bit weight and rotary speed, core recovery, and penetration rates are listed for each formation cored. In general, core recoveries were better from the mud-cored wells, whereas penetration rates were faster for the air-cored wells. Coring costs were about the same for single-formation wells cored with either mud or air; however, costs increased considerably when multiple-formation wells were cored with air.

Jan 1, 1969

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

Discussion of the paper of Dorsey A. Lyon and Robert M. Keeney, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 2117 to 2149. C. D. WOODWARD, Butte, Mont.:-We constructed a small blast furnace, and used first carbon electrodes and an alternating current of about 50 to 75 volts. We were able to smelt the material which was fed to the furnace, but we did not carry on experiments far enough to see just exactly what the power consumption was and compare it with the amount of material treated. We found that the blast seemed to help materially in reducing our charge and cutting down our power consumption. There were several other experiments tried at the time, and I do not call to mind now just what they were. We were trying to do away with the carbon electrode and replace it with an iron one, and it also seems to me we tried to use the ore for an electrode; but I believe that the electric furnace in the reducing end is simply a question of British thermal units per kilowatt-hour compared with British thermal units in a pound of coke. Now, if a pound of coke costs us 0.5 c. and a kilowatt-hour costs us in the neighborhood of 1.5 c., I think there is a big advantage in using coke instead of the electrical current for copper reducing. We tried steam, and a number of other methods, to throw copper down, but it has been some time ago and I am not very familiar with them now. The outlook of the experiments did not seem to be very promising, and we took it more as a thermal problem than an electrical one. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-Mr. Woodward has spoken of the question as a thermal problem. I would call attention to the fact that electric furnaces usually utilize the heat of the electric current at from four to ten times the efficiency with which the heat generated by fuel is utilized; so it will not do simply to compare by thermal units generated. Your total thermal units may cost much less from coke than from electricity, yet you will find the electrically generated thermal units utilized in a properly designed furnace from three to ten times more efficiently than in the combustion furnace. You must make that allowance is comparing the cost of thermal units generated electrically and thermal units from coke.

Jan 11, 1913

By H. B. Freaman, C. L. Colburn, C. M. Bouton

"The mine telephone has been perfected to such an extent that it is giving satisfaction in most mines were the wiring is well insulated. Very often the telephone cannot be depended upon on account of falls of rock, grounding due to worn insulation or extreme dampness. In the event of a disaster it frequently happens that the mine telephone system is put out of commission by the agency that causes the disaster, at the time when it is most urgently needed. On this account the mining industry is interested in any kind of telephone system that can be counted upon in an emergency. Many requests have been received by the Bureau of Mines to devise means of utilizing wireless methods for this purpose.The results of some preliminary experiments conducted by the writers at the Bureau of Mines experimental mine at Bruceton, Pennsylvania, in the ordinary sending and receiving of radio waves through earth strata are described below. The experiments were made in cooperation with the Westinghouse Electric end Manufacturing Co., which assigned to this work three of its radio engineers, C. A, Boddie, E. C. Douglas, and F. D. Fessler,The preliminary experiments consisted first in receiving signals from without the mine by means of a receiver located inside the mina, and second, both sending and receiving messages underground through the strata. It was found that with a receiving instrument set at a point 100 feet underground, signals from KDKA station, of the Westinghouse Electric and Manufacturing Co. East Pittsburgh, Pa., could be heard distinctly. Station KDKA is at a distance of about 18 miles from the experimental mine. About 50 feet from the receiving station used in this test was a 6-inch bore-hole from the surface, lined with iron pipe and containing electric light wires which extended therefrom through-out the mine. The presence of these wires evidently assisted greatly in the reception, for when the receiving set was carried to another point in the mine removed from wires and tracks the signals were barely audible through 50 feet of cover. The fact that signals were detected, however, even though faintly, is sufficient evidence of transmission through the ground to encourage further experimenting.In sending waves underground the Westinghouse 20-watt B.T. model T.F. transmitter was used in such a manner as to send out continuous waves of 200 to 300 meters length."

Oct 1, 1922

By Charles B. Kenahan

The chemical and galvanic corrosion properties of commercially pure titanium, a titanium-manganese alloy, a titanium-aluminum-tin alloy, 2 titanium-copper alloys, and 2 titanium-aluminum alloys were studied. Tests were conducted in synthetic ocean water, tapwater, 1-percent sodium hydroxide, 5-percent ferric chloride, and 5-percent ammonium sulfate solutions, various concentrations of sulfuric and hydro-chloric acids, and 1-percent oxalic acid. All tests were carried out at 35° or 60° C., with a flow of air or helium. Dissimilar metals involved in galvanic-couples experiments were aluminum, magnesium, and stainless steel. Electrode-potential measurements on single (uncoupled) specimens were also measured. Commercially pure titanium and the titanium-base alloys were generally quite similar in their resistance to corrosion, whether alone or in. contact with a dissimilar metal. Contact with the titanium metals caused aluminum and magnesium to corrode by galvanic action. Coupling with stainless steel in sulfuric acid solutions decreased the normal corrosion rate of the titanium metals. Contact with aluminum in air-aerated oxalic acid and 0.1N sulfuric acid solutions resulted in cathodic corrosion of titanium and the titanium-base alloys; however, there were a few exceptions. The copper alloys showed better corrosion characteristics than titanium in certain sulfuric acid solutions but were more susceptible to chemical attack in some hydrochloric acid solutions.

Jan 1, 1958

By Daniel G. Ganey

Kerr-McGee Coal Corporation has used diesel face haulage and support equipment at its dual-seam Galatia Mine in Southern Illinois since production activities commenced in 1983. The mine began production from its lower seam, the Harrisburg No. 5 coal seam, in October 1983 and from the upper Herrin No.6 coal seam in April 1985. Before production began, the company developed a program designed to make use of the flexibility offered by diesel equipment. While productivity was an important goal, the top priority of the program was to provide a safe and healthy work environment for the miners. Management believed that high productivity would naturally follow. History has proven this belief to be true.

Jan 1, 1990

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By D. J. Crawford

The Lucerne Valley Operations of the Minerals, Pigments and Metals Division of Chas. Pfizer & Co., Inca, are located about 5 miles south of the town of Lucerne Valley, California. These operations consist of several limestone quarries, a whiting plant which produces finely pulverized limestone products, a-kiln which produces granular quicklime and lime products, and maintenance shops, warehousing, shipping, and office facilities. Construction of the Lucerne Valley plant began in 1961 as the result of a decision to utilize large undeveloped reserves of limestone in that area. Quarry development was started in the following year; and by 1965, Lucerne Valley had become the principle limestone and lime facility of the Western Operations of the Minerals, Pigments and Metals Division.

Jan 1, 1967

By W. P. Diamond, J. R. Levine

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development pro- gram. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By D. J. M. Grodzian

Polymorphic transformations taking place in grinding processes, of massicot to litharge in PbO system, and of y to a in Fe203 system, were re-investigated. Grinding was carried-on in a steeel rotation mill charged with WC balls, under inert atmosphere. The kinetics of transformation in PbO was established by means of quantitative X-ray diffraction analysis. The resulting data fit a modified logistic growth function up to about 75% of transformed volume fraction, when a mixture at steady-state equilibrium is formed. The reasoning for the use of a modified logistic function is discussed. A sigmoidal growth function can be used if resulting data fit also an empirical power relationship between transformed volume fraction and time. However, it lacks the significance expressed by a modified logistic function. Assuming, the loss in magnetism is directly related to the amount of transformation in Fe 203, a quantitative analysis was performed using a magnetic balance method. The results fit only the modified logistic growth function, and transformation proceeds almost to completion. A wide literature survey of the subject is given. Available data from literature is compared with the results of the present study, and is shown also to fit a modified logistic grown function, with surprisingly similar slpes in a linear plot, independently of the material. The instrumentation effect on kinetics parameters, and the establishment of equilibrium mixture values, are discussed.

Jan 1, 1975

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument&apos;s ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By Frank Riddle

PRODUCTS made from the ores of the sillimanite group, and synthetic substitutes for them, have unique properties, and service tests prove that they are playing, and will continue to play, a major part in improvements in metallurgical processes. Also, they are examples of how comparatively useless, rare, or "museum" minerals have been made available in commercial quantities. Until research developed uses for them, the minerals had been observed only in small, scattered masses, or crystals. Improvements in ceramic processes and compositions have come about very gradually. In the last 10 or 15 years, several outstanding developments have been made. Of greatest interest to the mining and metallurgical engineers are those affecting the composition, necessitating the mining of new minerals, and improvements in ceramic products used in metallurgical processes.

Jan 1, 1932

By G. W. Jones

[As a part of its investigations pertaining to the promotion of safety, the Bureau of Mines is investigating various means, useful for the elimination or mitigation of the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explosibility of many complex, gaseous, combustible atmosphere may be calculated in a simple manner without the necessity of performing laborious laboratory experiment. In a previous publication4/ data were given and a method described whereby the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen, could be determined by calculation. The information published in that retort enables one to calculate the limits of inflammability of such gases are liberated by mine fires, gases from explosives, automobile exhaust gas, gases present after mine explosions, blast-furnace gas, and other gases containing part of or all of the above-listed constituents.]

Jan 1, 1938

Degussa&apos;s PAL-system (peroxide assisted leach) has been proven to be more economical than the conventional cyanidation technique. Significant in- creases in the gold recovery have been reported, accompanied by savings in cyanide. Accelerated extraction kinetics and modified reagent demands necessitate a redesign of the conventional cyanidation plant. The South African Osprey Mine is presented as an example of a successful PAL-application. Based on the plant and laboratory data it is shown that the redesign of the flowsheet can be an important factor for the effectiveness of a metallurgical plant. In the case of the Osprey Mine, the PAL-technology all ows a modification of the current preoxidation-ClPcircuit to two separate CIL-plants to treat run-of-mine ore and old tailings dumps. A doubling of the throughput is possible without enlargement of the plant. This innovation in the field of gold extraction, the combination of the PAL-process with a redesign of the metallurgical plant, can be considered as a basis for a more profitable gold mine.

Jan 1, 1991

By Yucheng H, Baogui Y, Wenyong L

High-water rapid-solidifying material, called &apos;high-water material&apos;, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of hackfill body. environmental contamination and so on, have been solved.

Jan 1, 1998

By P. J. Best

Due to its low mine production costs, competitive rail rates and low sulfur content, the Southern Powder River Basin (SPRB) now commands 30 percent of the U.S. utility coal market. In 1996, production exceeded 260 million tons, a growth of 110 million tons since 1989 and 15 million tons over 1995. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) looms. This growth will be the greatest in the southern part of the basin, where coal quality is higher. This article is an overview of supply and demand issues affecting markets for SPRB coal. It reviews the current markets for SPRB coal and addresses future prospects for market expansion.

Jan 1, 1998