Search Documents

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

[ ]

Jan 1, 1994

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By W. L. Sherwood

Present conventional techniques for primary steelmaking in both integrated and non-integrated plants are outlined. 'Direct reduction' alternatives are reviewed and categorized according to the nature of the product produced, with particular emphasis on the limited number designed to yield steel as the end product. A proposed new technique, referred to as the Sherwood Process, is described in some detail as a new combination of selected features from the prior technology. This process is in-tended to realize, in integrated operations, the result of continuons steelmaking directly from the ore in a single plant and, in non-integrated operations, continuons steel-making from a metallic charge of scrap, sponge iron or pig iron. Prominent features are continuons processing in elongated, horizontal, rotary furnace equipment, controlled direct heating of each process stage and, for the over-all integrated process, a size separation for removal of excess solid reductant and other waste just prior to the melting step. Material and energy balances are presented as well as exemplary cost data. Reasons for selecting this particular combination of process elements are dis-cussed.

Jan 1, 1968

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

By D Jensen, L Riffo, S Yu, F Traczyk, D Meadows

With the steady increase of molybdenum demand worldwide and the favorable molybdenum market, many technological innovations on both process and equipment have been developed and applied in many modern molybdenum plants around the world. This paper introduces the most commonly used molybdenum flotation flowsheet, together with the introduction of the flotation chemistry. Many different types of flotation cells are used in modern moly plants, and each type of flotation cell has its own unique advantages suited for particular ore and process conditions. This paper tries to provide some insight and guidelines in flowsheet development and flotation cell selection in the molybdenum plants.CITATION:Meadows, D, Jensen, D, Traczyk, F, Yu, S and Riffo, L, 2013. Molybdenum flotation circuit and flotation cells, in Proceedings MetPlant 2013 , pp 387-398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy Joint Venture in Madagascar is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behavior and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and both intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behavior of iron.INTRODUCTION The main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. The Ambatovy ore is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. Since the nickel content of the ore is roughly one fortieth that of iron, successful recovery of nickel depends on close control of the behavior of iron in the selected process. Exploration of the Ambatovy area, which is located to the east of Antananarivo, the capital of Madagascar, dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy Nickel Project. Dynatec then became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan (Collins et al., 2004, 2005, 2009; Collins & Vardill, 2005). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy Nickel Project, in 2007. The current Ambatovy Joint Venture consists of an integrated nickel and cobalt mining, processing, refining and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner) and KORES (27.5% owner)."

Jan 1, 2016

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

Jan 1, 1998

By Fernando Generoso Neiva Ferreira

O aumento crescente dos requisitos de segurança a serem atingidos pela indústria automotiva vem cada vez mais exigindo a utilização de aços com maior conteúdo tecnológico, que é o caso do aço bifásico (“dual-phase”), que são caracterizados por uma microestrutura ferrítico-martensítica. Neste trabalho, estudaram-se, em escala laboratorial, os efeitos das temperaturas de encharque intercríticas (750, 800 e 850°C) e distintas taxas obtidas por dois diferentes meios de resfriamento (ar e ar forçado) na obtenção de microestrutura bifásica a partir de dois aços laminados a frio “full-hard” (produzidos industrialmente), com micro-adições de Nb e Mo e diferentes teores de C e Mn. Utilizando ensaios mecânicos de tração, microscopia óptica (MO) e eletrônica de varredura (MEV), observaram-se as influências da temperatura de encharque e da taxa de resfriamento sobre as microestruturas resultantes e as influências da presença de ferrita encruada, dos carbonetos não dissolvidos e da morfologia da segunda fase sobre as propriedades mecânicas das amostras estudadas.

Aug 16, 2017

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

By N. W. Kirshenbaum

"The Marconaflo slurry system was originally developed to reduce costs and solve technical problems in the marine transport of mineral cargoes. In the short time since its inception, it has been found to offer economies and advantages for land-based and in-plant materials handling. This efficient method of reclaiming and slurrying particulate materials at very high pulp densities can be directly utilized in a wide variety of mineral process systems. These include: storage-reclaim applications, where even cohesive, compacted materials can be reclaimed from settled storage ""on demand""; the growing number of hydrometallurgical operations wherein slurried materials are processed to extract or yield metals; certain applications associated with pyrometallurgical treatment; and as a means of augmenting the performance of conventional mineral dressing equipment, such as thickeners.INTRODUCTIONIn the continuing effort to lower costs of producing minerals and extracting metals, the field of handling and transportation often receives too little attention from those engaged in the mining and winning of ores and metals. This comment, which pertains to ferrous and non-ferrous as well as to non-metallic producers, is especially pertinent to products having relatively low value, where transport costs can be a major portion of the delivered selling price to the minerals receiver.One method which was developed recently for the purpose of reducing costs and solving technical problems in marine transport and handling of mineral cargoes is the MARCONAFLO slurry system. A notable feature of this system is its versatility; in addition to its use in marine transport1*, some of its diverse applications have included the mining and reclaiming of tailings2 and in-plant materials handling3. As the concept and fundamentals of this system have been well explained previously4,5, the mechanics of the system will not be elaborated upon here. Rather some specific ways in which MARCONAFLO can be applied to processing and extraction will be explored."

Jan 1, 1973

By Knevitt L. T

PART 1Details of Kiewa Scheme.Introduction.Topography.Preliminary Investigations.Geology.Description of Project.Details of Main Works.Main Transmission of Power.Construction Facilities.PART 2Underground Works.Summary of Projected Works.Administration.Labour.Surveying.Safety and Accident Prevention.Medical Attention and First Aid.PART 3No. 4 Head Race Tunnel.Summary.Geology.

Jan 1, 1950

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By James C. M. Li, J. Weertman

James C. M. Li (United States Steel Covp.)—The author has discovered a single analytical relation between the minimum, or the steady-state, creep rate and the applied stress confirming a statement made earlier by orn" that such relation should exist and should reduce to the power law at low-stress levels and to the exponential law at high-stress levels. However, as pointed out by the author, all the available theories of creep are not adequate to explain such a single relation. Inspired by such a statement, I have made a suggestion concerning a possible explanation13 of the new relation. This is based on the concept that the rate-controlling step is the cooperative motion of a short dislocation segment. The nature of and the reason for the cooperation have been discussed13 as well as the reason why the motion of the dislocation could be controlled by the mobility of the short segments. A natural short segment has been proposed13 to be the node formed at the intersection of two dislocations. The reason why the node may contain only a few atoms has not been discussed and the application of the proposed model to all the metals and alloys reported in this paper has not been attempted. It seems appropriate to include these in this discussion. The model was partly inspired by the substructure recently observed in the electron microscope on creep specimens. One such example is shown in Fig. 48 in Darken's Campbell Memorial Lecture. The substructure is a collection of dislocation intersections and irregular networks. No pileups have ever been observed in such specimens. A closer look at the network indicates that one set of dislocations is more straight than the other set sug- gesting that the other set may be mobile in the plane of the net. Since, for the network to survive the creep deformation, some dislocation reaction has to take place at the intersection of the two sets of dislocations, the mobile dislocation, even if it can slip in the plane of the net, will have difficulty in moving at these intersections. To illustrate, an idealized network is shown in Fig. 9. The thin lines represent the set of dislocations which are mobile and can slip in the plane of the net except at the nodes which are formed at the intersection of the two sets of dislocations. The other set of dislocations, represented by the thick lines, may have a Burgers vector which is not parallel to the plane of the net, and therefore may be immobile. Because of this nonparallel Burgers vector, the Burgers vector of the node, which is avectorial sum of the Burgers vectors of the two sets of dislocations, will also be nonparallel to the plane of the net. Therefore, the node cannot slip in the plane of the net and the set of mobile dislocations will have to drag the node along as indicated in Fig. 9. Now the problem is how many atoms could be involved in the nodes. Exact calculation of the length of the node is a difficult task especially since the length should be a steady-state length and not an equilibrium length. An estimate of the equilibrium length can be made by balancing the line tension of all the dislocations. The results would be a small fraction of the length 1 between nodes as shown in Fig. 10. In some instances such a calculation shows that the node will not be formed. But, since the calculation is only approximate, it does not rule out the possibility of the formation of a short node. In other instances the equilibrium length of the node is an appreciable fraction of I. Such a node would

Jan 1, 1963