Search Documents

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African discard coal fines and K₂CO₃ blends were heated in a laboratory-scale rotary kiln to produce ashes for H₂SO₄ leaching tests. The optimized H₂SO₄ leaching conditions of 6.12 mol.dm³ (M) H₂SO₄, solid to liquid ratios 1:5 and 1:10, and 80°C for 8 hours were used. K₂CO₃ was added to increase the dissolution efficiency of K. The objective was to determine if the Al present in metakaolinite (Al₂O₃.2SiO₂), the Al, K, and Ti in the alumino-silicate glasses, and the Ti in rutile (TiO₂) in the ashes could be selectively dissolved in H₂SO₄. XRF results show that the ashes formed at 700°C dissolved more efficiently (87% Al, 89% K and 23% Ti) compared to the ashes formed at 1050°C. This can be attributed to the presence of Al₂O₃.2SiO₂, K₂CO₃ melt, K₂CO₃ remnants, KAl(SO₄)₂, and K-aluminosilicate glass in these ashes. XRD results indicate that the ashes prepared at 1050°C contained anorthite (CaAl₂Si₂O₈), microcline (KAlSi₃O₈), pseudomullite (Al₂O₃.SiO₂), and silicon spinel (2Al₂O₃.3SiO₂), which are either insoluble or only sparingly soluble in H₂SO₄. These minerals resulted in the lower dissolution efficiencies of Al and K. Based on the high dissolution efficiencies of Al and K for the ashes produced at 700°C, coal fines blended with K₂CO₃ could possibly be utilized as feedstocks for the production of aluminium(III), potassium(I), and titanium(IV) and a sulphate-containing leach liquor. Furthermore, the environmental issues and costs associated with the handling and disposal of large volumes of coal fines will also be resolved.

Aug 2, 2022

By Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of sub-micron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and industrial waste (4) desulfurization of oil

Jan 1, 1983

By Mayumy Amparo Cabrera-Ramírez

Polymetallic nodules are a widespread resource in the Pacific Ocean, particularly in the areas of Clarion-Clipperton (Cronan, 2000). The most abundant mineral phases are forme d by iron and manganese oxides, with minor elements such as nickel, copper, cobalt, molybdenum and rare earths elements (Cronan, 1977; Cronan and Moorby, 1981; Iyer and Sharma, 1990; Mangini et al. 1990; Banerjee et al. 1991). In the Clarion-Clipperton Zone (CCZ), several authors mention that there are three main mineral species of manganese oxides, which have been recognized and which are associated with different processes of formation: todorokita (Mn2+, Ca, Mg) Mn3 4+ O7. H2), vernadite dMnO and birnessite enriched in Fe and (Na, Ca) 0.5 (Mn4+, Mn3+) 2O4. 1.5 H2O. In nodules of hydrothermal origin have been found todorokite, birnessite, vernadite, goethite and pyrolusite. Although there are many oxides and hydroxides of manganese and iron in amorphous and microcrystalline phases that make up the bulk of the nodule (Frondel et al. 1960; Cronan 1977; Dymond 1981; Calvert and Piper, 1984; Aplin and Cronan, 1985; Martin and Lallier, 1993; Achurra et al. 2009), identifying specific mineral phases is difficult due to the intergrowth of different phases and associated detrital material.

Sep 14, 2011

Probabilistic seismic hazard analyses (PSHA) have now gained wide acceptance in the development of design criteria for major projects. When used with regional criteria the procedures have also allowed the preparation of more rational seismic zoning maps. Seismic zoning maps using various levels of results from PSHA studies around the Pacific Rim now include Canada, Indonesia, New Zealand and the United States. Some Pacific Rim countries such as Chile where the seismic exposure is dominated by subduction events have no subdivision into separate zones.Approaches to risk based zoning are being considered in several Pacific Rim countries including Australia. Australian studies must face problems similar to parts of the Eastern United States where seismic activity is low with irregular and infrequent occurrences of moderately large earthquakes. The perception of the seismic exposure by both regulatory agencies and the public at large is different when considering areas of low seismicity. There is therefore a need to make different interpretations of the results of PSHA studies in these areas of low seismicity. The aim of this paper is to explore some of these differences by comparing the results from two site specific studies from areas with widely differing seismic activity rates.

Jan 1, 1990

Éléonore Project Highlights Éléonoreis a multi-million ounce, high grade gold discovery in Québec Currently at the advanced exploration and engineering studies stage Excellent potential for expansion Underground mine with potential for small open pit Excellent infrastructure including road and high quality/low cost electricity within 70 km Les Mines Opinaca Ltée, a 100% subsidiary company of Goldcorp, was created to manage and operate the Éléonore Project

May 1, 2007

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By Guy B. Taylor, Horace C. Porter, E. C. White

When the Federal investigation of coal - dust explosions in mines was begun in 1908 , following a series of mine explosion disasters in 1907 , mining men generally questioned whether coal dust in air is explosive unless " gas " or methane is present , though perhaps in small amounts not detectable by a safety lamp . The experimental tests beginning in 1909 at the Pittsburgh testing gallery, and after 1911 , at the Experimental mine , demonstrated to the mining public the explosibility of coal dust in itself . There followed much controversy , both among practical mining men and scientists , as to whether the coal-dust particles uni te directly with the oxygen of the air, or whether gas is instantaneously distilled from the dust prior to explosive combustion , the gas enveloping each particle and propagating the flame from one to another . In considering methods of preventing explosions , this question made no difference for practical purposes , but it did have bearing in determining the relative inflammability of dusts of different coals . This led to the experiments by Guy B. Taylor and Horace C. Porter , on the momentary heating of the inflammable coal dusts , reported in this paper . Meanwhile , experiments on the inflammability of coal dust conducted in the Experimental mine , under my direction , and in the laboratory by J. C. W. Frazer and later by J. K. Clement and J. N. Lawrence , showed that different kinds of coal dust differ markedly in inflammability , thus confirming experiments made by Messrs . Taffanel and Durr at the Lievin Testing Station , France , and by various investigators in Great Britain . Both the French and British investigators concluded that their experiments demonstrated the distillation of volatile matter preceding inflammation .

Jan 1, 1922

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

By L. A. Taylor

The production of oxygen on the Moon utilizing indigenous materials is paramount to a successful lunar colonization. And several processes have been put forth to accomplish this. The LLOX generation schemes which have received the most study to date are those involving?: 1) the reduction of ilmenite (FeTi03) by H2, C, CO, CH4, CO-CI2, & Cl2 plasma, 2) magma electrolysis, both unadulterated and fluoride-fluxed, and 3) several others, including carbo-chlorination, HF acid leaching, fluorine extraction, magma oxidation, and vapor pyrolysis. The H2 reductions of ilmenite and magma electrolysis processes have received the most study to date. They are both feasible schemes with various pros and cons, including their feedstock requirements. However, all processes should be addressed at least at the onset of our considerations. There is an obvious need for considerably more experimentation and study. Some of these requisite studies are in progress, and this paper reviews several of the most studied and feasible processes for winning oxygen from lunar materials.

Jan 1, 1991

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By R. S. Busk

TWO groups of binary alloys were prepared. The first group consisted of those elements relatively soluble in magnesium: Li, Al, Zn, Ga, Ag, Cd, In, Sn, Hg, T1, Pb, and Bi. These are predominately Group B elements. The second group consisted of most of the remaining metallic elements, all of which are relatively insoluble in magnesium: As, Au, Ba, Ca, Ce, Cu, Ir, La, Mn, Ni, Pd, Pt, Rh, Sb, Si, Te, Ti, W, and Zr. These are all Group A, transition, or rare earth elements. Alloys of the first group were prepared by melting sublimed magnesium and elements as pure as obtainable in a graphite crucible, using a standard flux1 for protection. The melts were poured into a small graphite mold to produce 3xY4 in. diam slugs. Spectroscopic analyses were made of each slug. In all cases, the total impurity content was less than 0.05 pct. The slugs were then heat treated 5°C below the eutectic temperature until complete solution, as judged metallographically, was obtained. Filings from the center of the slugs were compacted at room temperature into 1/2 in. long x 1/4 in. diam cylinders, sealed in pyrex under 1/2 atm of purified argon, annealed at the heat-treating temperature for 1 hr, and quenched in water. After the X-ray diffraction patterns were made, each compact was analyzed chemically for the solute. It was found that the Mg-Li alloys reacted during filing to reduce the Li in solid solution. For this series of alloys, the slug was cold worked, annealed in purified argon, the surface dissolved in dilute HC1 to a depth of about 0.005 in., and the X-ray exposure made on the fresh surface. This procedure resulted in sharp, continuous lines and in true values for the lattice parameters. The alloys in the second group were prepared in the same way except that about 1 wt pct of each solute was added. Since the solubility limit was exceeded, not all the solute dissolved. These alloys were analyzed spectroscopically only to confirm the presence of the solute. The diffraction patterns were of the back-reflec-tion type using the characteristic copper radiation* and a flat cassette. Both the film and the specimen were rotated. The specimen temperature was maintained at 25" ± 1°C. The films had sharp lines; their diameters were measured directly to 0.01 cm. The parameters were calculated from the line diameters using a modified version of Cohen's extrapolation method.2 his method effectively eliminates systematic errors such as film shrinkage, inaccurate alignment, and non-precise film-to-speci-men distance. The random errors were minimized

Jan 1, 1951

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By K. Clifton, K. Kar, M. Gautam, J. T. Jurewicz

"This paper describes the history of LDV measurements employed in research involving gas-solid flows. Much of the discussion deals with measurement techniques employed to obtain separate and simultaneous solid and gas phase velocities. Also, LDV based measurement techniques that arc used to obtain particle size and concentration information in conjunction with the velocity measurements arc presented.INTRODUCTIONThere are numerous examples of industrial processes in which the motion of a solid or droplet dispersed phase in a suspending gas phase is critically important. The applications range from spray droplets injected into combustion chambers to the understanding of the time release mechanisms of particles generated by dissolving pharmaceutical tablets. In many of these processes, the heat, mass, and/or momentum transfer between the dispersed phase and the suspending fluid arc the items of interest. In the past, much of the phenomena were characterized by empirical models derived from flow averaged measurements. Gradual developments in laser Doppler velocimetry (LDV), have provided researchers with an unobtrusive measurement technique capable of obtaining the particle size velocity and concentration with good spatial resolution.In the two decades that LDV instrumentation has been available, most of the uses have concentrated on single phase fluid flow measurements. The light scattered from seed particles small enough to follow complex fluid motions, including turbulence, is converted into velocity information. While the utility of this instrument in single phase flows has been demonstrated beyond question, the use of LDV in gas-solid multiphase flows has had a more gradual development. The measurements ·of interest in these flow regimes are usually the velocity of the suspending fluid as well as that of the dispersed particulate phase. Early investigators were quick to see the potential of this instrument for measurements in gas-solid flows. The interest soon expanded to the development of instruments that could also simultaneously measure particle size and concentration within a two-phase flow field.This paper tracks the historical development of LDV technology as applied to gas-solid flows. The techniques to measure particle velocity, size, and concentration arc treated in separate sections although much of the development occurred simultaneously. Finally, some unique applications conducted at West Virginia University and other locations will be discussed in the application section."

Nov 1, 1995

By Pascal Turcotte

_ Introduction _ LaRonde _ Controlling Instability in Haulage Drifts _ Failure mechanism in drifts walls _ Failure mechanism in drifts back _ Field Behaviour of Support Elements _ The ?Hybrid Bolt? _ Conclusions

Feb 1, 2008

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat, area of northeastern Colorado. Sample 31310 was taken from the Continental Oi1 Co.'s well Briggs No. 1 which came in on September 27,7.931, with a maximum production of 940 barrels per day. Sample 31311 was taken from the Reiter-Foster Oil Co.'s well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day. These two samples of crude oil are typical "intermediate base" crude oils according to the classification defined by Smith and Lane. The characteristics of these two samples, as shown by the Hempel analyses, indicate that they are almost identical. They have a very low sulphur content, and the residuum has a low carbon-residue content which would indicate that they are excellent crude oils for refining. Crude oils yielding a residuum which has a carbon-residue content of 4 per cent or less usually make good material for the manufacture of cylinder stocks. The pour points of the samples and the cloud test of the fractions obtained from the vacuum distillation indicate that the Greasewood Flat oil contains considerable wax. The high wax content would cause some difficulty in transmitting this oil through a pipe fine during extreme cold weather.

Jan 1, 1932

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of more accurate detonators. The new and more accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1986

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene, plagioclase feldspar, and pyroxene which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals as well as reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilise the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. Reducing chromite recovery is of critical importance since high levels may negatively affect the downstream smelting process. Chromite recoveries can however be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. In summary, due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator, and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible.

By AIME AIME

MODERN metallurgy is an art and a science. The art is process metallurgy-extracting metals from their ores, refining them, and alloying them with one another and with certain nonmetals to produce thereby a variety of metallic materials which, owing to a wide range of useful properties, are for many purposes more valuable to man than the individual metals themselves; process metallurgy also includes shaping or otherwise treating metals and alloys to form objects useful to a complex industrial world. The science is physical metallurgy-organized knowledge of the constitution and internal structure of metals and alloys, of the relation of their composition and structure to properties, and of the laws, theories, and hypotheses that purport to explain this relation.

Jan 1, 1942

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939