Search Documents

By Sitotaw Y. Fantaye

"The first segment of the Second Avenue Subway extension is approaching construction completion. The new extension will operate along Second Avenue from 96th Street to 63rd Street, where it will divert west along the existing 63rd Street line, stopping at the Lexington Avenue/63rd Street Station. The new line will have stateof-the-art stations at 96th, 86th, 72nd and 63rd streets.Most of the two-track, twin-tunnel subway was constructed using bored tunnel methods (Figure 1), with a tunnel boring machine (TBM). The launch and retrieving box of the TBM was strategically located at the south end of the 96th Street Station where bedrock exists approximately 70 ft (21.3 m) below street level. The TBM launch box and the 96th Street Station (Figure 2), including the ancillary facilities adjacent to the station, were constructed by the cut-and-cover method. The cut-and-cover work required the contractor to design and implement a stiff, tightlybraced retaining wall, approximately 100 ft (30.5 m) long, to tie the existing tunnel constructed in the 1970s to the new station, temporary street decking over the entire excavation, and a wide range of excavation support systems at various locations.The cut-and-cover construction posed significant challenges including: installation of street decking on busy Second Avenue, relocation and suspension of the myriad utilities beneath the streets, and configuration of a lateral support system that would minimize movement of adjacent structures but not slow down excavation activities. This article describes the innovative solutions developed to manage and facilitate safe and efficient construction without disrupting Second Avenue, a major southbound one-way thoroughfare.The work was performed in several phases involving: (1) preconstruction condition survey of existing buildings, (2) installation of instrumentation and monitoring, (3) major utility relocation efforts to move vital utilities from within the alignment of the slurry wall on both the east and west sides of the avenue, (4) implementation of maintenance and protection of traffic plans, (5) installation of temporary street decking across the entire avenue and over the excavation to allow an orderly movement of traffic and pedestrians, (6) staged excavation and installation of an intricate temporary bracing system beneath the decking (7) step-by-step construction of the new subway station’s structure and (8) staged removal of the bracing as the structure gained sufficient strength to resist the lateral loads. The main focus in this article is the design and construction of the temporary street decking and lateral bracing systems; the utility suspension system and the north tie-in that allowed the daunting task of excavation and construction of a new subway station in bustling New York City, with minimal disruption to the community, businesses and everyday traffic."

Jan 1, 2016

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961

By D. W. Bridges, Donald R. Peterson, Masami Hayashi

Techniques are described for recovering about 80 pct of the cobalt and nickel contained in superalloy scrap by anodic dissolution of the scrap and simultaneous electrodeposition of a pure cobalt - nickel alloy at the cathodes in an electrolytic cell partitioned by permeable diaphragms into separate anode and cathode compartments . Superalloy scrap was alternatively prepared for subsequent anodic dissolution either by melting and casting massive scrap into suitably sized anodes , by packing moderate - sized discard scrap in inert metal baskets that subsequently served as anodes , or after concentrating the superalloy portion of grinding debris , by magnetic separation to reject corundum or other abrasives , slagging any remaining abrasives from molten grindings , and finally casting the superalloy metal into anodes . In the processing , purified electrolyte -- 1 N in NiSO4 and in NiCl₂ , and 0.1 N in CoSO4 and in CoCl2 --was charged to the cathode compartments and discharged from the anode compartments at a rate sufficient to overcome the backward migration of ionic impurities from the anodes to the cathodes . Discharged electrolyte was purified by reacting it first with SO2 and next with limestone , and then recirculated to the cathode compartments , in which a 50 pct cobalt - 50 pct nickel alloy was deposited on either blanks of stainless steel or starting sheets of cobalt - nickel alloy . The process was made self - sustaining by either adding H2SO4 to the catholyte feed to throttle the rate of cobalt - nickel deposition , thereby compensating for the slower rate of cobalt - nickel dissolution from the anode and losses occurring in electrolyte purification , or alternatively , adding H₂SO4 to

Jan 1, 1964

By Frank S. Wartman

[ ]

Jan 1, 1927

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By John E. Kinnison

The Mission mine, located in southern Arizona near Tucson, is a recently developed open pit which produces 15,000 tons per day of copper ore. The mine lies on a wide and gently sloping bajada sweeping northeasterly from the Sierrita mountains. It derives its name from the nearby Mission San Xavier del Bac, built circa 1700. The ore body is everywhere covered by about 200 feet of alluvium, as are the adjacent Pima and Palo Verde mines. The geology of the Mission deposit is known principally through the study of diamond drill holes spaced 150 to 300 feet apart. The open pit is in an infant stage and has not yet revealed much of the deposit, although information obtained there by the operating staff, and from a few thousand feet of exploratory underground workings, has added significantly to the general fund of knowledge. Permission to publish was granted by the American Smelting and Refining Company. I am indebted to Kenyon Richard and J. H. Courtright for criticism of this paper and for their direction during the several years in which I studied the Mission deposit. Acknowledgment is given to consultant in petrography, Robert L. DuBois of the University of Arizona. The only previous publication pertaining directly to the geology of file Mission deposit appeared in 1959 (Richard and Courtright), and may not be everywhere readily available. Cooper (1960) has published a short paper on the district

Jan 1, 1963

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By Batric Pesic

Silver dissolution with thiourea was studied by using the rotating disk technique. The major parameters studied were: thiourea concentration (0-0.5M), ferric sulfate concentration (0-0.5M), sulfuric acid concentration (0-0.5M), and the effect of many foreign ions (Mn, o.i, Co, Ca, Na, etc.). Temperature effect was studied in the range 5-35 .C. The activation energy was 5.4 Kcal/mole. The dissolution of silver was first order with respect to ferric sulfate, and the secord order with respect to thiourea. Among the additives, copper had a dramatically negative effect. The strong oxidants such as hydrogen peroxide and manganese dioxide were also detrimental for silver dissolution. Silver does not dissolve with thiourea in the absence of ferric ions. Sulfuric acid does not participate in the dissolution reaction either. Chemically, the most important parameter for silver dissolution is the ferric sulfate/thiourea ratio. Thus, in the solutions with excess of ferric sulfate, a solid silver-thiourea complex is formed, which precludes transfer of silver into solution. In the solutions with the excess of thiourea, the free thiourea reacts with formed solid silver-thiourea complex and silver goes into the solution. The solid silver-thiourea complex was characterized according to its chemical composition. The complex contains 6.54%C, 2.49\H, 14.77%N, 16.09%0, 21.62%8, and 37.13% Ag. This composition corresponds to a Ag2so4.3'1U.2ff:i0 compound The soluble silver species are present in the solution as the dimers of AgTU+3 complexes.

Jan 1, 1989

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract I for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 11, 1976

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Established as a Society February 26, 1957 OFFICERS AND COMMITTEES J W Woomer, President A B Cummins, President-elect S D Michaelson, Past President C E Lawall, Eastern Regional Vice-President D W Scott, Central Regional Vice-President 3 D Forrester, Western Regional Vice-President R B Ladoo, Treasurer John Cameron Fox, Secretary

Jan 1, 1959

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By Alice Y. Tseng, Dan MacLean

"Corrosion protection of all deep foundation systems made of steel is THE issue when considering durability of the element in the long term. Protecting steel from corrosion and maintaining the steel tendon cross sectional area ensures a competent and durable system. The foundation of a building is usually difficult to repair and therefore high risk is taken when unknowingly choosing a non-adequate solution.Requirements according to EN 1990 (Eurocode 0 or EC 0) on construction durability requires a service life over 100 years. How can a service life over 100 years be achieved? How shall bare steel be protected in soil, which sometimes could be an aggressive environment to the steel? Which corrosion protection methods are commonly used in Europe and in North America?This paper will focus on hollow bars used as Micropiles, Anchor piles and Soil Nails. It gives an overview about the state of the practice in regards to corrosion protection (including head construction) and evaluates different options following the European Standards focusing on type of material and method of installation. Further the different corrosion protective methods such as thickness of grout body, coating types and sacrificial loss are listed with the pros and cons evaluated.Based not only on North American standards like FHWA “Micropile Design and Construction Guidelines”, FHWA Geotechnical Engineering Circular No. 7 for “Soil Nail Walls“ and Post-Tensioning Institute “Recommendations for Prestressed Rock and Soil Anchors”, but also European standards like EN 14199 “Execution of special geotechnical works – Micropiles”, EN 14490 “Execution of special geotechnical works - Soil nailing”, EN 1537 “Execution of special geotechnical work – Ground anchors“, and other relevant standards, all possibilities of protecting the hollow bars and the steel quality will be introduced, discussed and compared ."

Jan 1, 2017

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the LaJoya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein(BPV) type, with a signi?cant amount of the gold reserves contained in the oxide cap.Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"Abstract - The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the La Joya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein (BPV) type, with a significant amount of the gold reserves contained in the oxide cap. Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By Y Li

An ilmenite ore from the Murray Basin was initially characterised using combined X-ray Fluorescence Spectroscopy (XRF), X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Electron Probe Microanalysis (EPMA) techniques. XRF analysis showed the ilmenite sample contained 58.7 wt per cent TiO2 and 26.2 wt per cent Fe2O3. Major impurities included: Cr2O3 (4.5 wt per cent), Al2O3 (2.7 wt per cent), SiO2 (1.9 wt per cent), Mn3O4 (1.5 wt per cent) and MgO (1.1 wt per cent). Manganese and magnesium were present as solid solution components within the ilmenite lattice while the elevated Al2O3 and SiO2 levels were due to separate aluminosilicate gangue minerals. Chromium was associated with discrete chrome spinel gangue phases of variable composition, (Fe,Mg)(Cr,Al)2O4. Quantitative XRD analysis of the sample identified rutile (12 per cent), ilmenite (11 per cent), and pseudorutile (67 per cent) as the main titanium-containing phases and chrome-rich spinels (seven per cent) as the major impurity phase. Minor quartz, aluminosilicates, zircon and monazite were also present. The ilmenite was mixed with synthetic graphite, pressed into pellets and reduced carbothermally in nitrogen at 1200 and 1400°C with C/O molar ratio of 1.2. Titanium oxide in the ilmenite was converted to titanium oxycarbonitride. Iron oxides were reduced to metallic iron. The Changes of impurities as a result of reduction was examined by SEM and EPMA analyses. Iron and chromium oxides within Fe-rich chromite were reduced to form a Fe-Cr-C alloy. Mg-rich chrome spinels were partly reduced at 1200°C. Zircon particles were not reduced at 1200°C, but were significantly reduced at 1400°C, with the particles becoming porous and the silicon being removed.

Oct 5, 2011

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010