Search Documents

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By D. Harrington

While apparently the hysteria with regard to silicosis and other occupational diseases has largely subsided and this subject is being more carefully considered and soberly judged, it would be poor policy for any employer to maintain that the storm has ended and that he can relax and revert to conditions as they were 5, 10, or more years ago. The fact is that the plan of paying occupational-disease compensation is now in its infancy and can be expected to grow rapidly. At present, while all of the States of the Union, including the District of Columbia and excepting only Arkansas and Mississippi, have compensation acts, only the following make provision for occupational diseases to some extent or in one way or another: California, Delaware, Connecticut, District of Columbia? Illinois, Indiana, Kentucky, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Jersey, New York, North Carolina, North Dakota, Ohio, Pennsylvania, Rhode Island, Washington, West Virginia, and Wisconsin. Silicosis is compensable in one way or another in California, Connecticut, District of Columbia, Illinois, Kentucky, Massachusetts, Missouri, New York, North Carolina, North Dakota, Ohio, Pennsylvania, West Virginia, and Wisconsin, and possibly in other States. During the past few months, occupational-disease legislation (largely silicosis) has been considered in some form in Arkansas, California, Delaware, Idaho, Maryland, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah and Washington. It will be surprising if comparatively comprehensive occupational-disease legislation is not on the statute books of nearly every State in the Union within the next 5 years. With this situation confronting him, the farsighted industrialist who has the interest of his organization at heart, if he has not already done so will immediately start to "put his house in order" by studying possible occupational disease hazards to his employees and promptly applying known remedial measures or attempting to devise such measures if none exist. Unquestionably, one of the most important of the surveys to be made relates to dust occurrence, as State laws on occupational disease are almost certain to contain provisions, on silicosis and, with almost equal certainty, the provisions of any State law are not likely to be particularly similar to those of other States.

Jan 1, 1938

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

By Pedro S. Zúñiga S.

El presente trabajo señala la optimización de los parámetros de perforación en el yacimiento minero de Cuajone a través del control de presión hidráulica y velocidad rotacional en la operación de máquinas de acuerdo a las formaciones geológicas consideradas. En este sentido, se busca mejorar el rendimiento respecto al desgaste de brocas y conservación de la máquina perforadora.

Oct 14, 1980

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 m (0-80 ft) and was naturally hydrophobic at greater depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5 m) could be upgraded by froth flotation at pH32 following slimes removal. The i.e.p. of samples varied regularly between pH = 1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure which in turn determines flotation-non-flotation relationships is postulated.

Jan 1, 1983

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962

By L. C. IlsLey

The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting,but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely how methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.

Jan 1, 1936

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By C. J. Simensen, R. Østhus, H. J. Roven, K. G. Skorpen, H. Kalager

"This work encompasses co-extrusion of alloy Al4.5Mg at the core and rapidly solidified Al4.5Mg1Ag forming the surface layer. The goal is to produce a multi-material by co-extrusion having a relatively hard surface as compared to a softer core. At the same time, work hardening in both alloys is expected to be significant due to Mg in solid solution. Precipitation hardening at 160°C is studied by applying solution heat treatments at 560°C. The hardness increased from 80 to 130 VH in the surface material after 236 h. Surprisingly, the Al4.5Mg alloy also shows pronounced aging at this temperature, i.e. from 70 to 90 VH. The relatively high solution heat treatment temperature introduces grain growth in the core, but this is insignificant for the RS surface alloy. Blisters forms at the surface and cracks follows large portions of the interface. However, the tensile ductility is significant in all conditions due to very pronounced work hardening, i.e. for the as co-extruded, T6, under- and over-aged. The elongation at fracture ranges between 40–45% and the tensile strengths 240–275 MPa. The tensile properties increase linearly with the thickness of the RS alloy, i.e. following the rule of mixtures.INTRODUCTION Al-Mg alloys in 5xxx-series are classified as non-heat treatable wrought alloys (Polmear, StJohn, Nie, & Ma, 2017). The formation of the binary ß-Al8Mg5 does not give a substantial increase in the strength of the alloys (Mondolfo, 1976). When a third element like Ag, Cu or Zn are added, G.P.?zones are formed at low temperatures and intermediate, partial coherent phases are nucleated somewhat higher temperatures and finally a ternary, equilibrium phase is formed (Auld, 1968; Cousland & Tate, 1986; Mondolfo, 1976). Both the formation of G.P.?zones and intermediate phases increase the hardness and strength of the materials. An intermediate, hexagonal T´?phase is formed in Al-5 wt%Mg-1wt%Ag, and finally the equilibrium, cubic phase (Al,Ag)9Mg5 is nucleated (Cousland & Tate, 1986; Mondolfo, 1976)."

Jan 1, 2018

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By A N. Gupta, C Joginadham, P Shiva Shankar

Cast boosters made with pentaerythritol tetranitrate(PETN) and trinitro toluene(TNT) give high velocities of detonation and are sensitive to initiation even under high pressures. However, the manufacture of the same involves heating of TNT to its melting temperature and mixing of dry PETN in it.

Jan 1, 1996

By J. S. Page

El objetivo del texto estriba en una descripción del panorama geológico de las regiones en las que la Cerro de Pasco Corporation realiza sus operaciones de extracción y exploración por carbón, a fin sirva de pauta y guía en este proceso minero. Para ello, se muestran algunos diagramas y descripciones de la geología de Goillard, así como en Jatunhuasi. Posteriormente se anota el grado y los tipos de carbón obtenidos en el país. Finalmente se advierte de que a causa de su origen y subsiguiente deformación, los mantos carboníferos adolecen de defectos y no se logra una adecuada explotación venta del mismo.

Jul 20, 1960

By John C. Taylor

"The non-ferrous pyrometallurgical industry has been under extreme pressure since 1980 and significant changes are taking place, principally in the copper, nickel and lead industries. This paper reviews some of these changes, particularly with respect to smelter capacity, major technical trends, and the industry's response to increased energy costs and environmental constraints.The Canadian metal mineral production for 1985 has been estimated at a value of over $8 billion, of which half is derived from copper, nickel, lead and zinc production. It is in our national interest that the Canadian industry remain competitive in the world market and continue its traditional contribution to the Canadian economy. IntroductionPyrometallurgy by definition requires energy, usually in the form of fuel, and produces process gas streams which can no longer be discharged directly to atmosphere in most countries. While the industry has been under varying degrees of pressure over the past fifteen years, it is just since the early 1980s that major changes have taken place, due, to a large extent, to an oversupply on the primary metal markets and depressed prices. These factors, combined with a surge in the price of oil, have resulted in some trends developing which must be recognized by those in the industry who plan to be in operation and competitive in the next decade.Although the value of Canada's mineral production, in terms of constant dollars, has decreased by more than 35% over the period from 1980 to 1985, the bulk of this production is exported and the industry still makes a significant contribution to the Canadian economy."

Jan 1, 1988

By V. K. Zworykin

THROUGHOUT its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes; it. has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron. Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction -at the very best a tenth-of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. To overcome it, a different imaging medium must be employed. The existence of such a medium became evident when it was demonstrated' that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed, Furthermore, although a wave length may be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light: Actually, the electron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. THE ELECTRON MICROSCOPE Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the electrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By José Raphael Olegário França

Separação eletrostática é o termo usado para todas as tecnologias de processamento que utilizam forças elétricas que atuam sobre partículas carregadas ou polarizadas sob um campo elétrico estático. O comportamento das partículas depende das suas propriedades elétricas, geométricos e tamanho das partículas. Portanto, a separação de espécies é possível se os parâmetros do campo elétrico e as propriedades elétricas diferentes das partículas são apropriados para o processo. No separador eletrostático de rotor as forças elétricas, combinadas com as forças gravitacionais e centrífugas agem sobre as partículas e são responsáveis pela separação mineral. No presente trabalho as forças eletrostáticas que agem no processo serão substituídas por um modelo de contato de coesão Hertz-Mindlin com JKR. O resultado apresentado, embora com limitações, conseguiu-se fazer uma boa estimativa do processo e alguns dos parâmetros do separador. Com a presente simulação é possível descrever o processo de separação além de permitir a redução de despesas de testes práticos, melhorar a compreensão das relações fundamentais, simular as influências dos diferentes parâmetros e por fim, estimar eventuais aumento de desempenho.

Aug 17, 2017