Search Documents

By W. H. Frederic, A. C. Fieldner, W. A. Selvig

"Low-rank coals have a pronounced tendency to disintegrate or ""slack” when alternately dried, and wetted by exposure to the weather. The more readily a coal slacks the greater is its tendency to ignite spontaneously and the more care must be used in its shipment and storage. Lignite slacks very readily when exposed to the weather. Slacking trouble is also experienced in shipping and storing subbituminous coal, but not to the same extent as with lignite. As a rule, bituminous coals are only slightly affected by weathering and in general may be classified as nonslacking coals. The slacking tendency of subbituminous coal is one of the characteristics that is used to distinguish it from bituminous coal. An accelerated laboratory method of test was developed to measure such slacking tendencies. This method was applied to a number of coals, principally from the State of Washington, and the method and the results obtained are given herein.Helpful information concerning slacking tendencies of coal was received from Marius R. Campbell, senior geologist U. S. Geological Survey.Coals that slack readily contain relatively large amounts of moisture. When exposed to the weather such coals lore moisture rapidly. As the coal loses moisture at the surface there is a gradual drift of moisture from the interior of the piece to the surface. If the loss of moisture at the surface proceeds at a faster rate than it is replaced by moisture from the interior of the coal piece, there undoubtedly in greater shrinkage of the coal at the surface as tom-pared to the interior of the piece and stressed are generated in the surface coal.These stresses in the surface coal cause it to crack and disintegrate.Likewise, when the air-dried coal is wetted by rain, the exposed surface of the coal pieces gain moisture more rapidly than the interior of the piece, causing greater expansion in the surface coal and the coal breaks down further. As this process of air drying and wetting is continued when the coal is exposed to the weather, the slacking proceeds and the exposed lumps of coal may disintegrate completely."

Nov 1, 1930

By Gabriela Pino, Maurício Torem, Lorgio V. Gonzales

It has been long known that many microorganisms are able to interact with mineral particles to obtain a concentrate; thus, one possible technique is flotation and its related process. Biological process have been attracting attention in mineral processing due to lower operating cost and their possible applications to process low-grade and fine ores. The adhesion of microorganism to surface of mineral particles can alter the hydrophobicity of mineral markedly. Such surface modifications modify its hydrophobicity or hydrophilicity will be used to flotation of cassiterite fines. The major difficult to float fine particles is attributed to the low probability of bubble-particle collision, one characteristic of electroflotation process is the ability to create very tiny bubbles, which is known, improve the collision efficiency and flotation performance of fine particles. In this study, the electroflotation of fine particles using Rhodococcus opacus strain as bioreagent was investigated. Electroflotation experiments were carried out using particles of cassiterite around 8µm of mean diameter the adsorption of R. Opacus onto cassiterite particles was confirmed by Fourier transform infrared spectroscopy (FTIR), electrokinetic and contact angle analyses. The measurement of bubble size by laser diffraction showed a mean bubble size of around 26 µm, current density and bacteria concentration appear to be the main parameters affecting the mean diameter of bubbles, electroflotation tests reported recovery around of 64.5 % at pH 5, concentration of 2,87 x10¹² cells/ml (50 mg/L) and current density of 51,4 mA/cm2.

Jan 1, 2014

By Gill Montgomery

At this moment in the history of the world, the all- pervading and universally most important fact is that the world population is beginning to outgrow its food supply, and the United States has suddenly lost its ability to give away huge food surplus to any nation in the world with a food shortage problem. This, of course, means that, all of a sudden, our government must completely reverse its former bureaucratic stance regarding crop controls and agricultural price supports, to out-right incentives to increase farm production and bring more idle land into food-growing use.

Jan 2, 1967

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By R. E. Johnson

Seventy years after the start of the Industrial Revolution in Great Britain, as reckoned from Arkwright's water frame patented in 1769, there was a significant development of the metallurgical industry in Virginia. In Britain, crucible steel had been rediscovered by Benjamin Huntsman in 17~0, and this made spring and tool steel more generally available. The metal-turning, screw-cutting lathe, including the basic principles recognized in today's engine lathe, was developed by Henry Maudslay about 1797. Wrought iron, as manufactured by Henry Cort's process patented in 1784, was readily available. Richard Trevithick's highpressure steam locomotive had met its test on the Pennydarren tramroad in 1804, and George Stephenson had built his famous Rocket, along with several other locomotives, at Newcastle around 1828. Puddling furnaces and a rolling mill had been placed in operation at the Tredegar Iron Works in Glyn Sirhowy, Monmouthshire, Wales, in 1807. In the United States, expanding commerce and a growing population resulted in continuing development from the Chesapeake to Virginia's Blue Ridge, and this demanded improved means of transportation. Ore deposits rich in hematite had been found in Virginia's Piedmont during the Colonial period, and a number of blast furnaces now dotted that area. The products of these operations were mostly pots, kettles, stove parts and like items for local trade. The James River and Kanawha Canal was incorporated in January 1785. Its eastern leg, winding along the slope of the high bluffs overlooking the river, was completed about 1800. About two dozen railroads were chartered in Virginia between 1830 and 1837. With expanding population and steady industrial development came a need for metallurgical products. Throughout the eastern United States, numerous metallurgical enterprises sprang up, and many of these flourished. The purpose of this article is to outline the development of one Southern metallurgical company, the Tredegar Iron Works, which was to have a significant impact on the industrial development of Virginia and the fighting of the American Civil War. Although the Tredegar Iron Works no longer exists, remnants of the early operations have been restored, and the current status of the site is also presented.

Jan 1, 1999

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

The Arctic is a region of special economic, geopolitical, research, socio-ethnic, and defense interests of both Russia and other countries of the Arctic zone. Introduction of innovation technologies at ore-processing factories is a direct responsibility of the state and this problem should be solved on the basis of coordination of interests of different stakeholders. The task of elaboration of scientific principles of rational state regulation in the North is very topical. Innovations require considerable investments first of all from private capital. However as an investment object innovations are not attractive for investors as they require large expenditures for long-term projects, and they are connected to high risks because market incentives form striving to get quick profits of private companies and result in a certain behaviour strategy while innovations need ?long money?. Under such conditions without state regulation of investment and innovation activities development of the mining sector in the Arctic practically has no prospects. At innovation development of mining enterprises economic growth is provided at the expense of active state innovation activities. The elaborated strategy of ore-processing enterprises should correspond to the modern paradigm of the ore-processing industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the AZR which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents. The main principle of creation of innovation technologies is to obtain more products of higher quality with minimal costs. This allows increasing ?productivity of the resources? several times. This principle makes increasing productivity of the resources the most important and in this case efficiency of use of the resources brings extra profits at the expense of lack of new costs such as payment for protection and utilization of wastes. According to the economic theory only ratio between demand and supply is able to fix optimal proportions in economy and to give necessary signals for investment activities of mining enterprises. In this context market for minerals and increase of mineral resources productivity do not create incentives for investment activities without which neither sustainable economic growth nor solution of macroeconomic tasks are possible. Nevertheless countries should not reject this idea in spite of economic efficiency of the enterprises. Extraction degree of useful components and especially oil in the Arctic zone is one of the lowest in the world. This can lead to crisis of oil industry and other mining sectors. The reason for that is lack of a state policy of realization of innovation technologies in the mining sector in the Arctic.

Jan 1, 2014

By M Watts, P Lindsay

Herbert Stream, a tributary of the Waimangaroa River on the Stockton Plateau, has elevated metal concentrations and low pH characteristic of acid mine drainage (AMD). Dissolved aluminium concentrations average 8.3 ppm, iron 1.4 ppm, manganese 0.69 ppm, and zinc 0.12 ppm and pH ranges from 2.8 to 3.2. Flow rates range from 2.3 to 26.6 L/s with an average of 5.3 L/s. To determine the effectiveness of different treatment strategies, a small amount of the AMD was diverted through three small-scale passive AMD remediation systems over an eight month period. These included a reducing and alkalinity producing system (RAPS), a limestone leaching bed (LLB), and an open limestone channel (OLC). Both the RAPS and the LLB performed well, effectively removing metals and restoring pH. The RAPS lowered aluminium concentrations by up to 99%, iron 97%, manganese 95%, and zinc 80% and the LLB lowered aluminium concentrations by up to 99%, iron 99%, manganese 92%, and zinc 91%. The pH was restored to between 6.4 and 7.4 by the RAPS and to between 7.3 and 7.9 by the LLB. The OLC performed well as long as the residence time was similar to that of the other treatment systems. OLC removal rates for aluminium was up to 99%, iron 94%, and manganese 21%, and the pH was restored up to 5.6. Due to its simplicity and effectiveness, it is proposed the LLB be constructed to fullscale size to treat the entire Herbert Stream.

Jan 1, 2007

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By Jesús Valdivia, Enrique Garay

El proyecto Shalipayco cuenta con 20 Mt @ 5.6% Zn, 0.5% Pb, y 1.3 oz/t Ag en recursos totales (M+I+I) a la fecha, consolidando por lo tanto uno de los más grande recursos inexplotados de mineralización de Zn-Pb-Ag tipo Mississippi Valley (MVT) en Perú. La dolomitización es una alteración que está asociada a los mantos mineralizados de Shalipayco y sirve como guía prospectivo. Cercana del depósito ubicase horizontes evaporíticos y brechas de colapso, que también pueden significar controles importantes para mineralizaciones MVT.

May 1, 2008

By Henry Kreisinger, WALTER T. RAY

This preliminary bulletin was written as the first of a series of several on the significance of drafts in steam-boiler practice, the succeeding bulletins to be along the same lines but of a more advanced character. The conclusions arrived at are tentative, and are the result of a study of one of the many problems growing out of a general plan of the United States Government to increase the efficiency with which the coals of the country are being used. Greater efficiency requires better boiler and furnace design. The experimental study of drafts on which the conclusions presented in this bulletin are based formed part of the fuel-testing investigations that were carried on by the technologic branch of the United States Geological Survey and have been transferred to the Bureau of Mines. The experiments made seem to indicate that it is possible to double or treble the capacity of a plant without making any radical changes the furnaces and boilers. These increases require about double and treble the quantities of air to be put through the fuel beds and boilers. It also seems probable that rebafHing the boilers will often permit the capacity to be doubled or trebled, while still getting more steam than formerly per pound of coal for uses outside the boiler room. These experiments were undertaken with the object of clarifying ideas concerning the passage of air through fuel beds and boilers. Measured weights of air were passed through two beds of lead shot, series, one of which remained always the same and represented a boiler; the other being varied as to size of shot and depth of bed, and representing a fuel bed. Careful observations were made of the weight of air passing through the beds per minute. All data were plotted in many charts, so as to permit the study of them from several points of view. A number of laws were deduced bearing on the relative amounts of power required to force air through fuel beds of various thicknesses, composed of various sizes of coal, and through boilers of various lengths and areas of gas passages. An important part of the discussion relates to an increase in the capacity of boilers by increasing the amount of power applied to pressure and exhausting fans and thus forcing several times as much air through the fuel beds and boilers. may be possible, as a result of these investigations, to raise the rate of working the boiler heating surface to three or even four times its present value. Such an increase would undoubtedly mean new designs of grates, stokers, furnaces, and boilers, especially fitted for high rates of working. Fan equipments designed to supply three or four times as much air under several times the pressure would be provided with more efficient engines, thus giving an additional factor favoring high-capacity working. It must be borne in mind, as stated above, that the results are tentative. It will cost money to force gases at high speeds through fuel beds and boilers, and there will soon be pressing need of such quantitative data as will enable the largest possible part of the energy imparted by the fans to be advantageously utilized. We desire, to thank our superiors, especially Messrs. L. P. Breckenridge and D. T. Randall, for their helpful criticism and suggestions.

Jan 1, 1911

By Frank S. Palkovits

Over the past 30 years, underground paste backfill systems have been implemented across the globe in many configurations, each with a primary focus of providing high quality backfill to enhance mine operations. However, a number of key design drivers are not always well understood within design engineering firms that occasionally undertake this work, leaving opportunities on the table. Perhaps not always obvious to those newly embracing paste technology, identifying key drivers and opportunities attainable through a paste backfill system is generally not straightforward, requiring innovative approaches to securing higher productivity, availability, performance, maintainability, and operator health and safety. This paper describes a number of applications and audits of paste backfill systems for several challenging mine operations. Key challenges include iterative design aspects of availability of good backfill materials, plant location and configuration, general arrangement, and binder receiving/storage systems.

Oct 1, 2010

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By Jorge Gibson, P. Chris Pistorius, Megha Jampani

"The main reason for the significant carbon intensity of integrated steelmaking (approximately 1.8 tons of CO2 per ton of steel) is the use of carbon-based reductants in blast furnace ironmaking. Several changes to blast furnace ironmaking have been proposed as ways to reduce carbon intensity and cost. A conceptually simple two-zone blast furnace mass and energy balance can be used to quantify the expected impact of such process changes on coke rate, carbon intensity, and productivity. Examples to be discussed include top gas recycling, combining lower blast temperatures with increased coal injection to produce a rich top gas, using prereduced feed, and tuyère injection of natural gas. The use of the operating window – which illustrates how allowable flame temperatures and top-gas temperatures constrain feasible oxygen enrichment levels – is illustrated. Increased use of natural gas would lower the carbon intensity of blast furnace ironmaking.IntroductionBecause of the significant carbon intensity of steelmaking (approximately 1.8 tons of CO2 emitted per ton of steel produced) and the high production rate of steel (more than 1.4 billion tonnes per annum), steelmaking is responsible for a large percentage, approximately 6.7%, of world anthropogenic CO2 emissions [1]. By far the largest input of the carbon into conventional steelmaking is as coke, which is essential to blast furnace ironmaking. A typical fuel rate for blast furnace ironmaking is 450 kg of fuel per tonne of hot metal (THM). (""Fuel"" includes coke and injectants which partially replace coke; pulverized coal and natural gas are typical injectants.) Assuming the fuels to contain 90% carbon on average, and since nearly all of this carbon exits the steel plant as CO2, a fuel rate of 450 kg is equivalent to a CO2 intensity of 1485 kg/THM – by far the largest part of the total CO2 intensity of steelmaking.Blast furnace ironmaking is expected to remain the main source of new iron units; this paper gives some estimates of the extents to which further reductions in carbon intensity from blast furnace ironmaking is possible. A recent European assessment suggested that blast furnace process intensification options such as increased pulverized-coal injection or natural gas injection would yield only modest energy savings [2]. However, if the focus is on CO2 emissions rather than on total energy use, there would be an advantage to using fuels – such as natural gas – which have lower carbon contents relative to energy content."

Jan 1, 2014

By J. G. Eberhort

ThE literature of surface phenomena shows that, except for most of the rare-earth elements, surface tensions have now been determined for almost every liquid metal. The situation for liquid metal oxides is, in contrast, characterized by a great scarcity of surface-tension data. A surface-tension correlation between these two classes of substances has been found which provides a means of estimating unknown liquid-oxide surface tensions from the corresponding known liquid-metal surface tension. Lf the surface tension of the liquid metal is a(M) and that of the liquid metal oxide is o(M,Oy), then oxides of all stoichiometries can be brought into one correlation if is plotted against with the surface tensions taken at the respective melting points. The available data is displayed in this fashion in Fig. 1 where the relationship between the surface tensions of the two classes of liquids is found to be The correlation in Fig. 1 is based on data found for nine liquid metal oxides and the corre- sponding liquid metals In cases where several sur-face-tension determinations were available on the same substance, higher values were generally favored over lower ones because they usually indicate greater Sample purity. All of the metal-metal oxide pairs are in good agreement with Eq. [I] except for B-Bz03. The reason for the departure of this pair from the correlation is not understood. To estimate the surface tension of other liquid metal oxides the corresponding liquid-metal surface tension must be found. A nearly complete bibliography of the surface tension of liauid elements is available in the 46th edition of the Handbook of Chemistry and physics. Some additional references on metals are included here for convenience Se,26Sr,'?ThanduZ5). It is also possible to estimate the surface tension of a solid metal oxide or metal from the corresponding liquid-state data. As a liquid material is cooled through its melting point the surface tension increases abruptly by an amount Ao. bondi' has estimated that the maximum value of Aa at the melting point is Ao = Ahf/A [2] where Alzf is the heat of fusion per atom and A is the area per atom in the interface. Thus with heat of fusion and crystallographic data the surface tension of a solid at the melting point can be estimated as o + Ao.

Jan 1, 1967

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By Charles C. Goddard

Since discovery of silver-gold lode deposits in 1864, the Butte district has produced more than $2.25 billion worth of copper, zinc, manganese, silver, and gold, an unprecedented value in the mining world. Exhaustion of the gold placer deposits along Silver Bow Creek, southwest of Butte, forced the early-day placer miners to turn their attention to the bold out- crops of the many veins exposed on the hillsides above the placer diggings. These outcrops bore silver and gold, and enough so that many lode claims were located. Such famous silver mines as the Alice, Moulton, Magna Carta, Nettie, and Blue Bird were developed. These and many smaller operations contributed to making Montana the leading silver-producing state in the 1880's. As depth was gained in the silver mines in certain parts of the district, occurrence of zinc minerals became troublesome. Zinc was not recoverable at the time, and in the chloridizing, roasting, and amalgamation of the ores, silver and gold recovery was greatly reduced. A period of active silver mining continued until 1892, when a decline in the price of silver brought the silver mining period to a close. Elsewhere in the district it was discovered that while some of the veins contained silver ores in the oxidized portions, the predominant minerals that were deeper were copper-bearing. Marcus Daly exposed rich copper ore on the 300 level of the Anaconda mine in 1891, and mining in the district disclosed that copper was destined to be developed in abundance. Early copper ore shipments were made to Swansea, Wales.

Jan 3, 1959

By R. Melley, P. Wissner

The paper looks at the basic theory of tri-bological wear and the role played by the lubricant and its additives. It presents the argument that the “real cost of lubrication” is not the purchase price of the oil or grease, but rather the costs associated with not using the correct lubricant. A number of examples are presented, covering oils, greases and additives, in which a detailed evaluation of the application has shown that when all of the benefits of using the best lubricant/additive are evaluated, the savings achievable greatly surpass the incremental cost of the superior lubricant. One of the emerging classifications of costs in industry today are those associated with environmental protection. Two of the examples used describe the replacement of more conventional lubricants with environmentally acceptable products, compounded to compete in all aspects of serviceability, but which have the added bonus of being not only biodegradable but also of being of low toxicity.

Jan 1, 1997

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984