Search Documents

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to over-produce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metal-based economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening. The metal age started many centuries ago, and with the exception of the noble metals, barely a dent was made in world reserves until the present century. Then, as a result of the pioneering ideas of D. C. Jackling and Paul Gemmel, and the willingness of the McNeals, Penroses and Guggenheims to back ideas with money, a virtual explosion of metal production was propagated throughout the world. It is important to examine the causes of this expansion to determine whether it is a trend that may be sustained or whether it is anomalous and therefore attributable to circumstances not likely to be repeated or continued. This period of plenty is a once only phenomenon. Vast metal resources have been sitting around here for eons, while the world was unaware of or unconcerned with their existence. But when population began to grow exponentially, and ways were discovered to use metals to develop machines to do the work of men and animals, the exploitation of raw materials increased at a staggering rate. And now the realization is dawning that minerals are a wasting asset and are beginning to present supply problems that should begin to be of concern. Two main factors have caused this condition; One is the population growth, and the other is the expanding demand for irreplaceable raw materials as nations become more developed. A group of systems analysts, at Massachusetts Institute of Technology in a book Limits of Growth, has warned that at present rates of population growth and resource consumption together with environmental constraints, a point will be reached within 100 years when the world population will become totally incapable of supporting itself. The authors conclude that this end result could be avoided if a planned equilibrium could be established at a lower rate of population growth and resource consumption. Fortunately, there is evidence that the population problem is moderating. The growth rate in the U.S. has decreased from 2.3% per year in 1900 to 1.1% in 1970. But, even at the lower rate, population will double in 70 years. The world rate is greater, and if it continues, world population will rise from 3.5 billion to nearly 10 billion in 50 years. All of these projections are questionable because the dangers of growing population are now being recognized. A marked decrease in growth rate has been noted in the more developed countries-in fact, it was zero in the U.S. in 1972. The other factor affecting consumption of raw materials is the increase in per capita use of most items as individuals become more affluent. Many economists believe that developing countries such as China and India represent a vast future potential market; but there are others, with whom the author agrees, who believe over-population tends to stagnate development. Nevertheless, it is a fact that vigorously developing societies increase consumption at a rate far above their population growth rate.

Jan 1, 1974

By AIME AIME

ARGUMENTS and discussions were not lacking either Wednesday or Thursday mornings, when the geophysicists got together. The first session, under the chairmanship of Paul Weaver, was devoted largely to theoretical papers, except for the first one by F. W. Lee, which was a progress report. This speaker mentioned some of the high lights of geophysical exploration during the last year, such as the recently announced extension of the Rand gold fields through magnetic exploration, and the continued activity in the oil fields of this country. Even this brought forth some disagreements, Paul Weaver feeling that credit was being given geophysics where it was not due for the discovery of certain oil fields. In this criticism Everette DeGolyer concurred, and both agreed that geophysicists must lean over backward when it comes to taking credit for discoveries. The troublesome question of interpreting resistivity curves is always being aired, and Lynn G. Howell's paper, presented briefly by the chairman, served to clear up a moot point raised last year by M. King Hubbert's work. By use of Maxwell's theory of images the author calculated that the effect of a thin, conductive sheet placed perpendicularly across the middle of a four electrode system should bring the resistivity curve up to a figure equivalent to the resistivity of the surrounding medium, but no higher. Variations from this he explained as being due to dirt on the surface of the sheet. The difficult question of interpreting three-layer curves was tackled bravely in Thomas Manhart's paper, presented in abstract by S. F. Kelly. The author seems to be attaining some success through dividing three-layer curves into two approximation curves of the two-layer type.

Jan 1, 1933

By William J. Potter, Roger N. Pyle

Introduction The primary ingredient for survival of mining companies during a recessionary period is to be innovative and resourceful in the structuring and financing of operations. Over the past decade, many mining companies have had to retrench and restructure their operations and to redeploy their assets just to survive. During the same period, traditional sources of financing for mining companies -- commercial banks, subsidized export credit loans and long term straight debt financing in the public markets -- became less available and more expensive. Meanwhile, new markets and new financing instruments provided new alternatives for mining companies. Those companies which exploited these alternatives greatly enhanced their capacity for survival and even for profitability. This article considers the strategies adopted by some companies to adapt to changes in this recessionary environment; the inadequacy of traditional sources of financing; certain of the new financing instruments, structures and markets which have become available; and how several mining companies have utilized these new instruments, structures and financial markets to improve their competitive positions. THE IMPACT OF RECESSION ON MINING COMPANIES AND TRADITIONAL FINANCING SOURCES In its 1983 year-end article "The New Economic Order" Mining Journal characterized many of the large private sector mining companies with operations in the industrialized countries as being "gripped between the jaws of high working costs and stagnating metal commodity prices." The article went on to characterize the Canadian mining industry in particular as being "in the difficult position of having to seek to sell the bulk of its output in a world market characterized by over-capacity, where production costs were determined by internal political and economic factors while prices were set by external competitive forces of supply and demand." Miners of a wide range of commodities in the industrialized countries have come to realize that their domestic mineral resources are in many cases no longer competitive with global sources of supply. To compete and survive they would have to rely on their technical and financial expertise in mineral exploration and development and in mining and processing. Strategies For Survival Global competition has compelled management in the extractive industries to improve their worldwide cost position. This is the only means whereby a mining company can differentiate its product and attain a substantial competitive advantage. During the past decade, for example, ASARCO Inc. and Inco Ltd. chopped their payrolls, postponed expansion plans and otherwise retrenched. ASARCO reduced its capital expenditures and cash requirements for operations in 1984 to a level almost equal to its internally generated cash. The company's finances were also strengthened by increasing total lines of credit from outside sources, by selling common stock, and by reducing annual pension funding through a change in actuarial assumptions. Other companies returned to their traditional organizational structure where they had a demonstrated competitive strength. Consolidated Gold Fields, for instance, resumed its operation as a mining finance house. Its capital investment programs are now devoted solely to resource development. In mid-1984, at a time of firming zinc prices, Union Miniere S.A. used the opportunity to integrate its smelting capacity and to direct investment to certain subsidiaries at the expense of less viable operations. Smaller corporations realized that it was not enough just to be the low-cost producer. For example, Drummond Coal Company in Alabama, which dominates its regional market due to its low-costs, has also developed a world-wide trading capability and has placed incremental tonnage from its own mines as well as brokered coal produced by others, thereby minimizing capital risk. In Canada, Campbell Resources has exploited difficult times by acquiring assets cheaply. In the process it improved its capacity to withstand cyclical economic swings by diversifying from solely a copper and gold producer to a company based upon asbestos, coal, copper, gold and natural gas.

Jan 1, 1985

By Manuel Estrada

"El presente texto señala un breve estudio sobre el aspecto técnico y de ingeniería de La Planta Sacracancha del Banco Minero del Perú. Dicha planta se encuentra a 4 600 m.s.n.m. en la zona denominada Sacracancha del distrito minero de Morococha, perteneciente a la provincia de Yauli, departamento de Junín. Se utiliza la planta Flow Sheet y los minerales tratados son los sulfuros de plomo, cobre, zinc y planta. Asimismo se describe el proceso de producción de la planta, procedencia, operación de la planta y servicios auxiliares como los laboratorios, almacenes, talleres, etc. "

Aug 20, 1965

By D. A. Wheeler, Rémi Tremblay

"INTRODUCTIONDuring the last few years, through Column Flotation Company of Canada ltd, the Centre de Recherches minérales has worked on the column flotation of coal, phosphate, feldspar, talc, graphite, copper, lead-zinc and diamond ores. The operating companies and prospective deposits were located in Canada and in other countries. Since these projects were financed by the concerned mining companies, all results remain confidential unless we obtain permission to publish. Three companies have graciously allowed us to use their information which I will describe in this text. These are the Polkowice copper mine in Poland, the North Coast Industries ltd graphite deposit and a talc company which preferred to remain anonymous. I will also describe our 2 inch column which was used for all tests. Data is also given on how to scale-up the 2 inch column to industrial size.Figure 1 presents a schematic of a flotation column. Feed, at a controlled rate and pulp density, enters at about 1/4 of the height of the column from the top. A controlled rate of air is bubbled into the bottom of column through a fine-holed sparger. The column volume between the feed point and the top of the sparger is called the recovery zone. Tailings, at a controlled rate, always slightly greater than the feed rate, discharges from the bottom of the column. This difference in feed and tailings flowrates is called the bias. The floated mineral is carried through the recovery zone on air bubbles which rise into the cleaning zone which is that column volume between the feed point and the overflow at the top. As the bubbles rise in this zone they are washed of gangue material by wash water which enters over the top of the froth layer. The froth layer is maintained at a given depth during flotation but this depth will depend on the froth cleanliness, for quite a bit of cleaning by wash water is accomplished in this layer."

Jan 1, 1988

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009

By J. F. McMahon

Introduction The greater portion of the information presented in this paper was obtained in the course of an investigation on clay gathering and its cost in the provinces of Quebec and Ontario (1). For assistance in the preparation of the paper, the writer wishes to record his thanks to Mr. Howells Fréchette, Chief of the Ceramics and Road Materials Division of the Mines Branch. Clays are mineral substances consisting essentially of hydrous aluminium silicate which become plastic when wet, fairly hard when dry, and stony masses when burned to a sufficiently high temperature and re-cooled. Shales are clays which have been indurated by the processes of nature. Millions of tons of clays and shales are won yearly for the production of brick, tile, sewer pipe, drain tile, roofing tile, fire-brick, china-ware, wall and floor tile, cement, and a host of other products. There are certain types of clay which, due to their particular qualities and limited distribution, are mined entirely or in part for sale to manufacturers, and are even exported from one country to another, as for example china-clays or kaolins, utilized in the manufacture of white-wares and in the paper industry, due to their consistent whiteness; ball-clays, utilized in the white-ware industry, due to their bonding power and whiteness; slip-clays, used in the stone-ware industry because of their glazing properties, and in the grinding-wheel industry for their burned bonding properties; and suspension-clays, such as are used in the enamelling industry. However, the great bulk of clays and shales won are used in the production of heavy clay products, and the manufacturer of these generally owns and operates his own deposit of raw material.

Jan 1, 1933

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By Alfred H. Brooks

LESS than a decade ago the consumption of coal in Alaska was practically limited to the salmon canneries and the few lode-mines and settlements along the Pacific coast of the Ter¬ritory. The sparse population of the interior depended on the forests, that of the shores of Bering Sea and the Arctic Ocean on driftwood for fuel. All this has changed. The thousands who have sought and mined gold on the Seward peninsula since 1898 have much impoverished the long-accumulated supply of driftwood, and at the same time the constantly increasing demand for fuel, on the part of the placer-camps and steamers, has resulted in heavy inroads being made on the accessible timber of the Yukon and its tributaries. While on the one hand the immediately available store of wood has decreased, on the other the consumption of fuel because of the rapid expansion of the mining and fishery industries and the attendant growth of population has much increased. Alaska, therefore, offers a constantly growing market for coal and other fuels. As the local coal-production has been insignificant, the demand has been met by importations from Washington, British Columbia, and even from Pennsylvania and Australia. Fuel-Consumption Mr. D. H. Jarvis, Collector for Alaska, has kept systematic records of the trade of the Territory since 1903. The statistics of the coal-importations of the past two years are shown in Table I. If data were available for a longer period of years, the increase of coal-importations would be much more striking.

Jul 1, 1905

By A. W. Lovett

"THE last two years have been years of recession or, perhaps, years of marking time, depending upon whether the observer is a pessimist or an optimist. There has been a slackening in the industrial tempo that has been reflected in many ways in the national economy. As one of the chief barometers of economic health, the consumption and supply of energy reflect this slowing up.These same two years have also seen significant changes in the relation between the sources of energy. In periods of declining demand, it has happened in the past that coal, as the basic or residual source of energy, has shown the effects to a greater extent than the other energies. In these two years, however, in addition to this usual effect, there has been the acceleration in the Joss of market to diesels in the railway consumption category and the continuing decline in domestic consumption. The story of these years is presented in the statistical tables that form the foundation of this paper. Statistics, particularly in the form of tables, are rather dry and are sometimes difficult to follow but the overall developments are illustrated by graphs which present a more striking picture."

Jan 1, 1959

By T. E. Howard

The western phosphate field, comprising parts of Idaho, Montana, Wyoming, and Utah, contains one of the world's largest known reserves of phosphate rock. Although phosphate-rock deposits of good-grade have been known since before the turn of the century and production has been recorded since 1906, real development of this important field did not begin until immediately after World War II. Since then fertilizer-manufacturing facilities using western phosphate rock have been expanded, and three electric-furnace plants for producing elemental phosphorus have been installed, resulting in a rise in mine production from 323,955 long tons2/ in 1945 to 1,653,916 long tons3/ in 1953. Interest in the field is increasing, and it is reasonable to expect that the western phosphate industry will continue to expand. Before 1945 all western production was from underground mines. In that year the first strip mine in the field was started near Montpelier, Idaho,~ and in sub-sequent years a number of other open-pit mines were opened in southeast Idaho and western Wyoming. At present the major part of the production comes from surface mines. Underground mining has continued, and new underground mines have been opened in the field, but recent exploration by operating companies has been aimed primarily at developing additional deposits suitable for low-cost surface mining. Preliminary reserve estimates by the Federal Geological Survey5/ indicate that only a very small part of the total resource may be recovered by surface methods and that the industry eventually must depend largely on underground mining. Because one function of the Bureau of Mines is promoting the conservation and development of the Nation's mineral resources, it is appropriate that research be conducted to develop low-cost maximum-recovery underground mining methods applicable to western phosphate-rock deposits.

Jan 1, 1956

By C. W. Davis

This paper is the second of a series of progress reports on a study of the hydrometallurgy of manganese which is being, conducted in an endeavor to make possible utilization-of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of S02 gas on manganese oxides at elevated temperatures may prove of value.

Jan 1, 1930

By Oliver Bowles

In its geologic sense the term marble is applied to rocks consisting of crystallized grains of calcite or dolomite or a mixture of the two. Although limestone has the same chemical composition as marble it differs in that the component particles of calcium or magnesium car- bonates are granular and noncrystalline. In marble the crystals may be intimately intergrown, whereas limestone is an aggregation of unrelated particles cemented together into a solid mass. In its commercial sense the term marble has a much wider applica- tion. As susceptibility to polish is one of its chief commercial assets, all calcareous rocks capable of polish are classed as marbles. Lime- stones that show little crystalline structure may, if they take a good polish, be classed as marbles. Furthermore, serpentine rocks, even if they contain little calcium or magnesium carbonate, are classed as marbles, as they are commercial substitutes of true marbles.

Jan 1, 1916

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

By Donald O. Capstick

A mineral survey of the 520-acre Quigg West Wilderness Study Area (MT-074-155) was conducted by the U.S. Bureau of Mines in 1986 at the request of the U.S. Bureau of Land Management in order to evaluate its identified mineral resources. The Wilderness Study Area is in Granite County in western Montana about 16 miles northwest of Phillipsburg and 27 mi les northeast of Hamilton, MT. Stony Mountain, a study area on lands administered by the U.S. Forest Service, is about 1 mile to the south-southwest and was studied concurrently. No mineral resources were identified in the Quigg West Wilderness Study Area, but high grade gold assays, as much as 1.24 ounce gold per ton, were obtained at the one prospect found. Samples from four workings contained significant gold; minor silver, molybdenum, and copper were also present. The prospect containing the narrow and discontinuous gold-bearing quartz vein straddles the south boundary of the Wilderness Study Area. The shear zone containing the vein projects toward the old Crescent mine, about 4.5 miles to the south, which shows a similar geologic structure.

Jan 1, 1987

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high-and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines.

Jan 1, 1966

By Frank E. Cash

Data on the accident experience of the pebble-phosphate industry in Florida for 1930 and 1940 are combined in this report with statistics for the 9-year period 1930-38, inclusive, which were published in Information Circulars 69173/, 69684/, and 71005/. The periodic compilation and publication of such data enable the pebble-phosphate industry, as well as other industries, to consider the relative hazards, compare experience, and thereby help to prevent accidents. ACKOWLEDGMENTS Accident data were furnished by the following operating companies: Amalgamated Phosphate Co., Brewster; American Agricultural Chemical Co., Pierce; Coronet Phosphate Co., Plant City; International Agricultural Corporation, Mulberry; Phosphate Mining Co., Nichols; southern Phosphate Corporation, Bartow; and Swift & Co., Fertilizer Works, Bartow.

Jan 1, 1941