Search Documents

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No.4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 1, 1974

By W. L. Dare

This circular is the first of a series of publications describing uranium mining on the Colorado Plateau. Later circulars are planned in which exploration, development, and mining methods and costs will be described after a detailed study of various operations. Because of the introductory character of this paper, those well-publicized phases of the industry such as geography, history, prospecting, and exploration are described but briefly. Primarily, attention has been devoted to the general problems that are encountered in mining ore bodies and to the factors that affect the selection of development and mining methods. Those familiar with mining may class the information contained in this paper as elementary; however, its inclusion is considered necessary for the completeness of the series of papers. It will also serve as a source of information for people who are interested in uranium but are unfamiliar with mining.

Jan 1, 1955

By Albert L. Toenges

This report is the second of a series describing methods and systems of mechanical mining; where operations are conducted on more than one shift. The first report, Information Circular 7014,4/ describes mining operations at 14 mines and the present paper describes operations at 11 additional mines. The purpose of this study is to analyze the advantages and disadvantages of the various types of equipment and mining systems now used where more than one shift is worked per day. Physical conditions vary in different and in the same mining districts and determine, together with economical considerations, the systems of mining and the types of mechanical loading equipment to be used. The information presented in this paper may be helpful to operators or others who may contemplate installing a mechanical mining system. The equipment used in the mines described comprises conveyors, scrapers, mobile loaders, mobile conveyors, and combination of these types. The description of the mining systems and practices at the mines investigated is detailed only as they relate to and affect mechanization. In computing the operating data in mines that are not totally mechanized, employees not working directly on production have been charged to output from mechanized sections in proportion to the percentage of mechanization. The operating data for comparing various systems are for an average working dry, as the number of men working on idle days varies greatly in different mines.

Jan 1, 1939

By Frank E. Scott

During the past year interest in the use of hydrazine and hydrazine hydrate as a fuel has increased in the United States; For this reason it was felt to be desirable to obtain information on the explosives properties (if these materials in order that hazards inherent in their manufacture, storage, transportation, and use might be evaluated.

Jan 1, 1949

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977

By D. B. Dreisinger, M. Mokmeli, B. Wassink

Dissemination of selenium and tellurium in sulphide minerals results in the contamination of pregnant leach solutions and electrolytes in the hydrometallurgical treatment of sulphide ores and residues. The selenium and tellurium content of the copper sulphate-sulfuric acid solution may be reduced into insoluble precipitates of copper selenides and tellurides using cuprous ion. This study presents the use of the thermodynamics and kinetics for the removal process of selenium and tellurium in real life application. Dominant species of selenium and tellurium in acidic copper sulfate solutions were identified and the reduction rates of species were compared. The findings were applied to industrial conditions by modeling the Vale’s CRED (Sudbury, Canada) plant’s selenium and tellurium purification circuit. Rate reducing factors on selenium and tellurium removal were identified and discussed.

Jan 1, 2014

By Joseph B. Cummings

"Occurrences of fluorite on the Packard property were first examined by an engineer3/ of the Bureau of Mines in July 1943 as the result of receipt of an application for an access road. In August of the same year the showings were examined by a geologist4/ of the Federal Geological Survey. The property was again examined by an engineer5/ of the Bureau of Mines in March 1944. This last examination resulted in a proposal that access be gained by construction of a truck trail and that the Bureau of Mines undertake to explore the fluorite showings.The truck trail was constructed by the Public Roads Administration, which began the work on February 17, 1945, and completed it 8 days later.The Bureau of Mines exploratory program was completed on May 16, 1945. It consisted of stripping overburden, trenching, test pitting, tunneling, sampling, and topographic mapping.In addition to being described in some detail, the extent of the work as well as results are shown in accompanying tables and figures.Mrs. Rhoda A. Packard, Mrs. Nora 1. Cline, and C. B. Pettingill, all of Tonto Basin, Ariz., own the property, which comprises four contiguous, unpatented lode mining claims recorded at Globe, Ariz., as the Walnut and the Bluebird 2, 3, and 4. The claims are situated in T. 6 N., R. 11 E., Gila County. David L. Roscoe of Tombstone, Ariz., holds a lease and option to purchase.Access to the property is by Highway 88 from Globe, 34 miles to Roosevelt, thence 24 miles by a graded county road along the west side of Roosevelt Lake to Tonto Basin. Here the Greenback Ranch road, constructed by the Forest Service and maintained by the county, crosses Tonto Creek and continues easterly to the foothills. The truck trail leaves the road 8.5 miles east of Tonto Basin and runs 2.5 miles in a southerly direction to the property. (Fig. 1.)The fluorite deposits lie in and along a small canyon in a rough, rocky area at an altitude of about 3,400 feet, Vegetation is scant and of the usual desert variety. The summer climate is dry and hot and the winter climate moderate. Rainfall at the Forest Service Station in Tonto Basin was 11.4 inches from May 1944 through March 1945."

May 1, 1946

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other's oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945

By Thiago Marques Ivaniski

A fabricação de componentes para conformação mecânica possui uma gama de exigências devido aos esforços cíclicos, como por exemplo, fadiga térmica. Devido à capacidade de formar geometrias complexas e usinar metais de alta dureza, a eletroerosão (EDM- Eletrical Discharge Machining) possui eficiência na produção destas matrizes. O estudo da integridade superficial do material erodido torna-se importante para avaliarmos qual são as condições ideais para tratamentos termoquímicos que visam a otimização da superfície da matriz usinada. Neste trabalho, foi investigada a integridade superficial do AISI H13, utilizadas para a fabricação de matrizes de forjamento a quente. Foram avaliadas a rugosidade e camada afetada pela técnica de Perfilometria Mecânica,Microscopia Ótica (MO) e Microscopia Eletrônica de Varredura (MEV). Verificaram-se diferentes superfícies, em diferentes parâmetros de usinagem e profundidades estabelecidas, observandose a subsuperfície do material.

Aug 17, 2017

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

resident Schloss called the meeting to order at 9:30 a.m. Bob Dean, manager of the Hotel Colorado, gave a brief explanation of hotel policies governing the swimming pool, and also extended an invitation to the Institute to return in 1963, and stated that the dates June 30 through July 3 were available for next year. He also stated that June 28 through July 1 were available for 1964. He felt that holding the convention during the 4th was not good policy, and that dates prior to or following the 4th would make for better attendance. John A. Reeves, chairman of the Resolutions Committee presented the following resolutions: RESOLVED: That the members of the Rocky Mountain Coal Mining Institute in convention assembled, hereby ratify and confirm all official actions of the officers, the Executive Committee and other committees of the Institute between June 28, 1961, and the present time.

Jan 1, 1962

By Alfred Bodenlos

"El presente texto señala los acontecimientos geológicos en la Cordillera Negra y la deposición de travertino por las fuentes termales todavía activas al oeste de la población de Ticapampa. Los minerales fueron depositados principalmente como rellenos de fisuras, siendo cavernosos y en partes bandeados y sus temperaturas conocidas de formación varían desde baja hasta moderada, lo cual, además de su textura porosa, sugiere que están comprendidos entre las clases epitermal y mesotermal, según sistema propuesto por Lindgren. "

Sep 1, 1957

During the interval 1929-41, geophysical exploration in Russia made considerable progress, as reflected in publications. The greater part of these publications was available during the preparation of Geophysical Abstracts and Ms been abstracted in them. The rest was not received and remained unaccounted for. A considerable portion of these lading publications are now listed in bibliographic form, in view of their interest to geophysicists. All publications entered in the bibliography are in Russian. 1. GRAVITATIONAL METHODS 1. Abakelia, M. S. The Organization of Gravitational Observatories in Transcaucasia. Problemy Sovetskoi Geologi, Moscow, vol. 6, No. 5, 1936, pp. 452-454.

Jan 1, 1945

By J. Zegarra Wuest

El objetivo del presente texto es la determinación de un método capaz de obtener obtener una alta recuperación y concentrado comercial de tungsteno a través de conocer las principales variables que posee dicho mineral en su concentración. Para ello, se evalúa cuál es el flow sheet más conveniente, la flexibilidad del método para el tratamiento de minerales conteniendo menos de 2.5% W03 hasta 0.50% W0 3 y el efecto de la molienda en la recuperación de los diferentes constituyentes valiosos.

Nov 20, 1967

By M. Guney, A. R. Bell

In Mindola mine on the Zambian Copperbelt, there is a plan to extend the current production level of 1.2-1.5 km (3,900-4,900 ft) with five additional production levels. Research work indicated that the present total heat output of 38.6 MW will inevitably increase to 63.2 MW in 25 years. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 33.8/40.2°C (93/104°F) and 35.3142.10C (95/108°F) respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9, 000 MW.

Jan 3, 1984

By Russell Dayton

THE metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concern-ing the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chal-cography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Konigsberger,(1)? in 1909, was the first to apply polarized light to the microscopic study of

Jan 1, 1935

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975

By James R. Kerr

Although metallurgical benefits of processing metals in a vacuum or reduced atmosphere have been realized for a hundred years, the problem of creating a vacuum in the range from 10-0 to 10-4 mm. of mercury in a moderately sized furnace chamber has been difficult to solve. The demand for these and lower pressures, with the advent of World War II, for separating the fission-able uranium isotope from its stable twin by the electromagnetic process, gave impetus to developing pumps capable of delivering extremely low pressures. With the release of data by the Atomic Energy Commission on methods of securing high vacuum in large equipment, steel companies took the initiative, and the growth of the vacuum-melting industry was assured. Vacuum-induction melting of steel in the United States began on a small scale in early 1945 and in 10 years grew to 60,000 pounds per month or 720,000 pounds per year. The years following 1954 showed tremendous expansion, culminating in 1958 in a capacity of more than 36 million pounds.

Jan 1, 1962

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976