Search Documents

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are investigating technology and methods to monitor the blind areas around large haulage equipment used in surface mines. On average, six fatalities a year can be attributed to equipment colliding with other vehicles or pedestrian workers, or backing over the edge of a dump point. Several off-the-shelf technologies exist for monitoring areas that an equipment operator cannot see from the cab, including radar, video cameras, and radio signal detection systems. NIOSH researchers have tested many of these systems on large dump trucks both at their test facility and at surface mines. This article discusses the technologies available for this application and their effectiveness in detecting objects near an off-highway dump truck. Also, guidance is presented for mine safety personnel who are planning to evaluate collision warning systems or cameras on their haulage equipment. Available Technology Over the past few years, the number and types of systems available for monitoring the blind areas around heavy equipment have increased. Systems marketed for the automotive and recreational vehicle industries have been around for a while. Small video cameras can be found

By J. P. Morris

"INTRODUCTION In the investigation being conducted by the Bureau of Mines concerning the production and utilization of sponge iron, it soon became evident that more information was needed regarding methods for determining the degree of reduction attained in the manufacturing process. Sponge irons made by different processes vary in physical characteristics and chemical composition, and a method of analysis that is suitable for one type is not necessarily applicable to all others. For example, the hydrogen-evolution method, which measures the volume of hydrogen evolved upon treating the sample with acid, accurately determines the oxygen content of some types of sponge iron. However, when the sponge iron contains combined carbon, hydrocarbon gases are also-evolved and large errors may result. Probably no single method will give accurate results in all instances, and for this reason it is desirable to have several reliable procedures available and to know the limitations of each.For measuring the degree of reduction, determination of either metallic iron or oxygen should suffice, although for practical application of sponge iron to the production of steel the oxygen content is more significant. After consideration of proposed methods of analysis in regard to their suitability for routine use and the probable influence of other substances, four procedures were chosen for investigation:(1) Mercuric chloride method.(2) Copper sulfate method.(3) Hydrogen-reduction method.(4) Hydrogen-evolution methods."

Sep 1, 1945

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels ? from mining and processing to the manufacturing of Anished products. In 2009, the estimated real GDP of the United States decreased by 2.4 percent compared with, and the estimated nominal GDP was about $14.2 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. In 2009, the continued decline of the housing market was reflected in reductions in the production and consumption of cement, clays, construction sand and gravel, and crushed stone (those mineral commodities that are used almost exclusively in construction). Production of mineral commodities associated with the manufacture of goods for the housing market, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard also decreased. Declines in auto-mobile manufacturing resulted in reduced production

May 1, 2010

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By R. F. Droullard

The Bureau of Mines has used gross alpha and gross beta detectors to continuously measure radiation working levels for a number of years. During this time, improvements have been made in the design and performance of continuous working-level (CWL) detectors. This report discusses the improved designs and some of the operating principles and applications of CWL detectors in the measurement of radon daughter products in mines and dwellings.

Jan 1, 1985

By Robert A. Clifton

This Bureau of Mines report discusses the mineralogy of zeolites, the properties that make them commercially valuable, the conditions of formation of both natural and synthetic zeolites, and present and potential markets.

Jan 1, 1987

By J. Howard Bird

The purpose of this publication is to discuss grounding mediums and the phases of grounding related to corrosion and cathodic protection. The material presented is believed to contribute to a better understanding of this subject. It also indicates more effective methods of reducing corrosion damage to metal structures and equipment in the mining industry by cathodic protection. The authors do not intend to discuss technical aspects but rather to explain the general principles of this method of inhibiting corrosion. The relationship between soil resistivity, protective grounding, and corrosion is presented. Corrosion causes the annual loss of billions of dollars; which can be greatly reduced. Losses in the mineral industry can be excessive owing to the extensive use of direct-current power, the presence of considerable dampness, and the frequent, indiscriminate use of dissimilar metals.

Jan 1, 1958

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By Stephen Gale, David Clarry, Edmund Smith, Jon Feldman

"In 2006, a Canadian steel maker embarked on an ambitious initiative to become “Best in Class in Energy Management”. This initiative provides the framework for this paper, with some augmentation from other energy management projects carried out by Hatch. The initiative focused on identifying energy/GHG management improvements leading to low-cost implementation of energy savings or GHG emission reduction. The key components of the approach were:• Review site energy management practices and benchmark internationally.• Review best technical practices and benchmark against public energy intensity data.• Conducted a site-wide Energy Assessment and physical review of operating areas.• Facilitation of on site-workshops with staff to prioritize savings opportunities, as well as identify and remove implementation barriers.• Development of an Energy Management Action Plan for implementation of improvements.Most organizations can produce, with relative ease, a list of ideas for saving energy, implementing them is the challenge. This paper addresses these issues as well as the profitability of the energy efficiency improvements and the consequences for GHG emissions.IntroductionWhen one of the authors was an undergraduate engineering student at the University of Cape Town in South Africa, the technical drawing instructor made a statement that was both humorous, and mildly profound. He claimed that the most successful engineer is one who is both lazy and diligent. Lazy, in the sense that the engineer is constantly on the lookout for an easier, more efficient, way to do something. Diligent, in the sense that the engineer will work tirelessly to come up with a good technical solution for the easier way. This paper, somewhat of an anomaly in a compilation of technical proceedings, hopes to break the mould a little, and to show a “lazy-diligent” way of reducing the carbon emissions from an industrial facility, using a steel plant as an example."

Jan 1, 2008

By W. O. Macha

El presente texto señala la importancia del Sink and Float como método de concentración que facilita la explotación de minas de bajas leyes anteriormente desapercibidas en la industria minera. El estudio se divide en dos partes: la primera describe las generalidades de dicho método, mientras que la segunda muestra las pruebas metalúrgicas desarrollas con minerales de las minas "Casapalea", "San Cristóbal" , "Yauricocha" y "Tajo Abierto" de la Cerro de Paseo Co., así como las de "Austria Duvaz" "Victoria" y "Germania"de la "Negociación Minera y Metalúrgica Lizandro Proaño S . A . ", y la de "Sacracancha Gale". Como consecuencia de estas pruebas de Heavy Media, se encontró que el 75% de minerales tiene posibilidades de ser pre-concentrados por este método, asimismo la importancia del Sink and Float radica en el campo de los minerales usados corno relleno en las minas y de las abandonadas canchas.

Jul 20, 1960

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

By Dan Witkowsky

In an increasingly environmentally conscious world, mining's importance to society has often been misunderstood and even maligned by the public. Extreme and impractical ideas have often been presented to children because of the lack of accurate, timely resource materials available to educators. In the late 1960s. two mining engineers, S.P. "Pi" Warren and C.L. "Lindy" Barker, became aware of this situation. They proposed to develop a summer field course to provide a factual overview of the minerals industry for teachers. The pair believed that teachers could become better informed to educate students, and future generations, about mining. These two Colorado Mining Association (CMA) members felt that such a course could reduce much of the misunderstanding about this vital industry. This could be done by providing a balanced perspective of mining, not only for kindergarten-through-grade-12 teachers, but also for the students they would be teaching during their careers. Students who better understood the minerals industry could better formulate an unbiased view of it. The course would seek recognized authorities from industry, academia and government who would lecture in their respective fields of expertise. The course would provide a total concept of the coal, aggregate, metals and industrial minerals industries. It would include geology, geophysics, exploration, mining, processing, marketing, product applications, economic, mining history, careers, and environmental responsiblity. When possible, site visits would permit educators to view operations and to meet the men and women who are industry leaders. Teachers would pay a small tuition fee. The balance of the program expenses for each teacher would be paid through scholarships provided by industry and individuals. The "total concept" idea obtained the support of the minerals industry. The support of CMA's Education Committee and the Colorado School of Mines (CSM) was obtained in 1968. Colorado's Commission on Higher Education approved teacher recertification credits through CSM's Office of Special Progams and Continuing Education for those successfully completing the program. The first six-week series of classes presenting the total concept of the indus¬try was held at CSM in 1969. In 1977, the CMA Education Foundation Inc. (CMAEF) was established as a Colorado nonprofit corporation. The "Total Concept of the Mining Industry" (Total Concept) course was placed under its sponsorship. CMAEF is dedicated toward this continuing education program (Table 1). In 1994, the course was streamlined to four-weeks for six hours recertification credit.

Jan 1, 1997

By Cristiano José Scheuer

Experiments were carried out aiming to study the influence of micro-abrasive wear test variables and plasma treatment parameters, on the tribological characteristics of low-temperature plasma carburized AISI 420 steel. The first part of this study was conducted in order to evaluate the influence of abrasive particle size, normal load and counter body rotation speed on carburized sample wear behavior; and the second part was conducted in order to evaluate the treatment temperature and time effect on carburized samples wear behavior. Plasma carburizing treatments were performed at 8 and 12 h, for temperatures ranging from 350 to 500°C; and at constant temperatures of 400°C for times between 12 to 48h, and for 450°C for times of 4 to 16h. Micro-abrasive wear test were performed by mean of a calowear ball-cratering equipment using a polished ball of AISI 52100 steel rotating at 80, 120 and 160 rpm, for sliding distances from 2.6 to 104.2 m. Alumina abrasive particles with sizes of 0.05, 0.3 and 1.0 ?m were employed. The normal loads applied on this study were 0.1, 0.3 and 0.5 N. Carburized sample was characterized by mean of OM, XRD and hardness measurements. Worn crater characteristics were evaluated by confocal laser microscopy. Results showed that the transient wear regime prevails along the outer layer length (composed by Fe3C and ?’C), and the steady-state wear stabilizes in the diffusion layer region (composed by ?’C). It was verified that the wear rate and wear coefficient decreases with treatment temperature in the range of 350–450°C and increase for 500°C. It was also verified that the wear rate and wear coefficient decreases with treatment time in the range of 12–36 h (for 400°C cycle) and 4–12 h (for 450°C cycle), and increase for larger treatment times due the chromium carbide precipitation. It was also found that the wear coefficient increases with the increase of abrasive particle size, and decrease with the increase in counter body rotation speed and normal load. Lastly, the analysis of the worn craters indicates the occurrence of grooving and micro-rolling abrasion wear mechanisms.

Aug 17, 2017

By AIME AIME

THE section delegates assembled Monday morning with the incoming president, W. H. Bassett, in the chair and F. W. Bradley as vice-chairman. The secretary called the roll and urged the delegates to become familiar with the activities of the Institute. He explained the allotment of funds to local sections and the uses to which these funds may be put. He also announced plans for travel by Mr. Bassett and asked the delegates to confer with him as to meetings en route. An invitation was extended for all section delegates to attend the Directors' dinner Wednesday evening. He suggested that local sections hold a meeting once a year under the auspices of each division of the Institute. He further explained the system of choice of publications by members. The question of licensing of engineers was brought up, and the consensus of opinion among the membership was asked for. Because the matter is controversial, no official action has been taken and it was suggested that the' local and State sections act separately in this regard. A. B. Parsons, the assistant secretary, next spoke. In his remarks he indicated surprise that many prominent mining men still did not belong to the Institute, and urged that section delegates make up a list of such prospective members and send it in to the office for study by the New York staff. He also asked that re- ports of all meetings be turned in for publication in MINING AND METALLURGY, and said that the reports

Jan 1, 1930

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

By RUSSELL C. FLEMING

THE important advances that have been made of recent years in mining and milling methods and in mechanical equipment at mines need no re- telling, but there has been a remarkable growth in one type of equipment which has gone nearly unnoticed. That is the increasing use of storage-battery locomotives underground. Since the war the number of these locomotives and their field of use have increased tremendously; their growing acceptance represents an al- most complete reversal of opinion from an earlier period when they were generally looked upon as in- adequate for the strain of mine service. At the time when storage-battery powered units were first making their bid for recognition, the use of power in haulage had already passed through several phases; hand tramming, rope haulage, compressed air locomotives, even gasoline locomotives, had all been used, ending finally in the general adoption of the electric trolley locomotive for practically all power-haulage requirements. It was, and is, conceded that the trolley loco- motive met more adequately the varied and severe conditions of mine service than any previous type of haul- age unit. Subsequent developments have had to endure comparison and surpass in performance that type of haulage before changes would be considered.

Jan 1, 1930

By Fearnsides W. G.

The second part of the paper, presented at the Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, addresses the post-Carboniferous and pre-Permian movements which brought about the partition of the area and gave to the North Midland district its individuality as a separate coalfield. As earth-movements of several ages subsequent to the Carboniferous have played a part in the formation of this particular coalfield, the aim is to elucidate the effects which belong to the post-Carboniferous and pre-Permian Period and to disentangle them from those of later date. This is done by comparing the geometry of the folded surface of one of the more important horizons in the Coal-Measures with that of the surface of unconformity which divides the Permian from the Carboniferous rocks in South Yorkshire, Derbyshire, and Nottinghamshire

Dec 1, 1916

By Paul M. Tyler

The alkali metals , sodium and potassium , and more particularly sodium , occur abundantly in chemical combination with other elements . The elements themselves are available in metallic form but are so active chemically that they oxidize rapidly in contact merely with the air . Potassium will even catch fire spontaneously in air , and both the metals will decompose water with explosive violence . Inasmuch as they are almost as soft as wax they are not suitable for the structural or other mechanical uses characteristic of ordinary metals , and consequently the uses of these elements even in the metallic condition are based upon chemical rather than physical qualities . Sodium metal is used largely as a commercial reducing agent , but potassium metal is rarely found outside of chemical laboratories . Numerous salts and other compounds of these elements enter largely into world trade and are commercially very important , but none of these compounds except sodium peroxide and sodium cyanide are made economically from the metals . Sodium is generally considered as rather an uncommon metal , but in point of annual tonnage produced it is far more important than mercury , magnesium , molybdenum , bismuth, cadmium, cobalt , gold , silver , or the various rarer metals .

Apr 1, 1932

By C Dick

Over the past three decades, mining operations have seen a significant increase in the use of contractors for mining, camp management and catering, recruitment, maintenance, power management, and commissioning. More recently contractors have been engaged for stores and logistics, OH&S, environmental, exploration, training etc. In some countries, such as South Africa, the trend is towards total outsourcing of all aspects of a mining operation which is coordinated by the owners’ management team.During the Global Financial Crisis (GFC) more Australian companies considered and/or took on this approach to recruiting for both projects and operations as mining companies were forced to rethink their corporate strategies as commodity prices plummeted to low levels, pushing operations and projects into potentially financially unviable territory.This paper discusses the labour recruitment, commissioning and operating strategy of Western Areas NL (WSA), with the assistance of Independent Metallurgical Operations Pty Ltd (IMO), as it progressed construction, commissioning and operation of the Cosmic Boy nickel concentrator at the Forrestania Nickel Project during and post GFC. The use of IMO contractors allowed Western Areas to mitigate labour cost risk during the uncertainty caused by the GFC and let their management team focus on the task of bringing a new operation into viable and profitable production.

Aug 8, 2011