Search Documents

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By A. E. Brugger

SOME 2,000 years ago Pliny is supposed to have said, "Out of Africa always something new." It may perhaps even now be news to a great many that the Belgian Congo has in recent years been producing approximately a quarter of a ton of diamonds annually. For that is what the 1 1/4 million carats, the recovery from 40-odd operating mines, and about 20 or 25 per cent of the world's normal consumption, amounts to. In 1915, first exploitation operations produced less than 50,000 carats from two mines. The rapid expansion of operations following the Euro¬pean war meant a most rapid development of a virgin land. The interior is now reached by air in one day from the mouth of the Congo River, where steamers unload mail and passengers from Antwerp. This trip formerly consumed 4 to 6 weeks by a narrow-gage, wood-burning, railroad around the rapids of the lower Congo and Livingston Falls; by river boat to the heads of navigation, Djoko Punda on the Kasai or Luebo on the Lulua; and thence by caravan of native porters over narrow-trails to head¬quarters on the Tshikapa. Hundreds of miles of automobile roads have been constructed over veldt and through forest, bridging streams and ferrying rivers. The railway from Capetown to the Katanga copper district to the East, once two months away by trail is now reached in 2 or 3 days over fair automobile highway. Native "boys" who a few short years ago wore little more than a smile and a string of beads and to whom a wheelbarrow was a complicated piece of machinery, are today driving Fords, tending boilers and engines and operating electrical equipment, or are capable mine workmen, machinists and artisans, and dressed in all manner of cast-off white man's clothing. Even as late as 1920, due to difficulties of securing and transporting machinery during and just after the war, the crudest hand operations were the rule for the excavation, sizing, and concentration of the diamondiferous gravel. All washing and concentration is now mechanized, using steam or electric power, and where operations are sufficiently large to permit competition with native labor costs, excavation and transportation are also accomplished by machinery.

Jan 1, 1932

By E. P. Youngman

At the time of the preparation of the monograph upon the mining legisla- tion of Newfoundland, by the Imperial Institute of London, the existing local statutory law (as distinct from case laws and the applicable English acts) con- sisted of the following legislation: 1. Chapter 129 of the consolidated statutes, entitled "Of Crown Lands, Timber, Mines and Minerals," as amended by the Crown lands act, 1928. 2. Chapters 131 and 132 of the consolidated statutes (acts relating to mines regulation and rewards for discovery of minerals, respectively). 3. Crown lands act, 1918, as amended by the crown lands (amendment) act, 1921. 4. The Labrador Act, 1927. 5. The Crown royalties act, 1927. 6. Crown lands act, 1928, together with rules and regulations issued thereunder.

Oct 1, 1932

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

By Frank E. Cash, Roy G. Stott

This circular describes four modern change houses of the Lake Superior iron - ore district , all conceived and constructed since 1937. The oldest change house described herein was constructed and occupied in 1938 , yet it embodies the modern improvement of air - conditioning . The purpose of this report is to describe and illustrate improvements with regard to health and safety features combined in the construction , arrangement , ventilation , heating ,lighting , and other features , with the aid of photographs , sketches , and diagrams . The modern change house is a fire - resistant structure in which intermingling of men in mine clothes and men in street clothes , hazardous dust , heat and humidity , crowding , poor lighting , slippery and muddy floors , and inadequate facilities for clothes and for bathing have been largely eliminated . The miner coming off shift at a modern mine no longer faces the elements when he gets off the cage . He travels through a tunnel to the change house , where he is cooled gradually by room temperatures as he passes from the mineclothes section and shower room to the street - clothes room . He is assured of dry clothes when he is ready for them . No longer is he sent out of the change house into a muddy yard to drive away as best he can . The modern change house has an improved parking lot and graveled or concreted walkways from it to the change house entrances .

Jan 1, 1949

This document is Volume II of a two-volume report on underground and surface metal and nonmetal mine fires occurring between 1950 and 1979. Two surface fires from 1980 are included. Volume I discusses the methods of data acquisition, data analysis procedures, and results and conclusions. This volume contains (1) a master list of all fire incidents obtained from MSHA reports, (2) an annotated bibliography of all MSHA reports, journal articles on selected incidents, and non-reportable fires (appendix), and (3) indexes to be used in accessing incidents in the master list and annotated bibliography. These three types of information provide the reader with a complete summary of metal and nonmetal mine fires during the period from 1950 through 1979 and a convenient means to locate incidents of specific interest. The body of this volume is organized around two tables and a series of indexes. The two tables are master lists of underground and surface fire incidents. They are followed by 15 indexes keyed to the master list and annotated bibliography. The Appendix contains three different parts: ? The annotated bibliography of MSHA fire reports (one section each for underground and surface mine fires). ? The annotated bibliography of journal and other periodical articles about selected fires from the MSHA bibliography. ? A listing of non-reportable fires (one section each for underground and surface mine fires). Descriptions of the contents and use of each of the three major components of this volume (i.e., master list, indexes, and appendix) are presented in Section 2.0.

Jan 1, 1980

By Dale C. H. Nevison

One of the most intensive of material rivalries is the confrontation between zinc die castings and plastic injection moldings. Pressed hard by the plastics industry, zinc die casters are learning how to make parts with less material yet without sacrificing quality. The key to this new trend is the technique of Thin Wall die casting. The obvious benefits of Thin Wall are lighter weight and lower cost. Again, obviously, these are the very selling points that put plastics into many appliance and automotive parts formerly made of zinc. One of the factors that has been most conducive to the outstanding growth of plastics has been the increasingly prevalent concept that "adequate" properties are sufficient, especially if there are cost advantages. Most of modern design today is oriented around the reasonable life of a product, rather than indefinitely extended life. This is simply an acknowledgment of the existence of a design environment that pervades many areas, reflecting the life-cyclic desire for change. Too often, so-called "weight-saving" materials end up being very costly - not only in production, but in durability and dependability. Change for the sake of change usually doesn't effect a change for the better. In the majority of cases, the best bet is to design in traditional materials and minimize the material needed, while maximizing the efficiency of the production process. Component prices of products to be produced from either plastics or zinc must be studied in detail to determine which material will produce the lowest cost of manufacture. It is not uncommon for two parts, similar in appearance at a casual look, to have a considerable difference in energy requirements and production costs. Detailed cost estimates of the advantages of each material should therefore be prepared for zinc and plastic parts before the final design and material selection decisions are made.

Jan 1, 1978

By M. A. Reuter, N. J. Bartie

Metals make modern societies function, and increasingly, various high purity precious and special metals endow sustainability-driving technologies with specific functionalities. These metals become heavily intertwined within products, complicating end-of-life treatment. To counteract the resulting downcycling and potential depletion of scarce resources, maximising both the quantities and qualities of materials recovered during primary extraction and recycling, processes should be a priority in the pursuit of sustainable circular economy. Adopting a process simulation approach; a digital twin for the life cycle of cadmium-telluride solar photovoltaic (CdTe PV) modules was created. The system comprises an integrated metallurgical production system that produces, among others, cadmium, tellurium, selenium, zinc, copper, and lead, all of which are required to manufacture PV modules. System-wide resource efficiency and environmental impacts are assessed using exergy analysis and life cycle assessment, respectively. Simulation of this large and complex product life cycle at a high level of detail allows for the evaluation of potential system-wide effects of various production, recycling and residue exchange scenarios aimed at maximising the sustainability of the entire system. It diminishes the need to make arbitrary choices about allocation methods for the distribution of environmental impacts in multipleoutput production systems. Furthermore, it demonstrates the key importance of metallurgy in achieving circular economy. Keywords: Circular economy, sustainability, simulation, metallurgy, CdTe photovoltaics, life cycle assessment

Jan 1, 2020

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By Norman A. M Macleod

FOR the past seven years, all flotation at the Britannia mill has been done in Forrester Air-Lift cells. Prior to 1931, the roughing and part of the cleaning operation had been performed in four 21-cell and two 14-cell M.S. machines. The resulting economies in reagent, power, maintenance, and general operating costs, and the increased recovery, more than justified the exclusive use of the Forrester machine. About three years ago, the possibility of still further improving the efficiency of the flotation section was the subject of considerable discussion and experiment. Arising from these experiments, tests were made of the practicability of using a cell of greater depth than that of any pneumatic or mechanically-agitated machine in common use. Cells were constructed with depths of 7 .5 feet, 10 feet, and 15 feet, and, in all cases, a very definite improvement in operation was indicated. The cell now being used in the mill treats from 5,500 to 6,200 tons of dry feed per day. It is 100 ft. long by 5 ft. wide by 8 ft. deep, and has replaced a total length of over 500 feet of standard Forrester machine. The choice of a depth of 8 feet was governed by the type of blower which was available-in this case, a Roots-Connersville blower, driven by a synchronous motor and delivering 6,000 c.f.m. of free air at 4.0 pounds per square inch. At the Chelan Division of the Howe Sound Company, where a new mill was recently built, all flotation is carried on in cells 10 feet deep, with good results.

Jan 1, 1938

By B. K. Baird

The application of cutoffs during and after pit optimization is examined for a lower-grade multi-metallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block, incorporating parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which of these parameters have a significant effect on the total contained resource tonnage and total contained non-discounted revenue in the optimized pit. The cumulative effect of changing several of the more significant parameters is investigated. Application of a copper cutoff grade to a block inside the optimized pit could result in the less than optimal extraction of the resource. A block with copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher copper grade block may be sub-economic. The relative merits of applying a copper grade cutoff, "equivalent grade" cutoff and dollar value per ton cutoff to blocks inside the optimum pit are discussed.

Jan 1, 1999

By Jorge Díaz A

El presente texto revisa los métodos utilizados en las minas de tajo de abierto como son la perforación, disparo y seguridad y así mejorar los standars y el rendimiento futuro en la industria minera. Respecto al primer método empleado, se analizan los factores que afectan el rendimiento de brocas y cómo dicho factores varían, impidiendo la adaptación de prácticas universales de perforación. Asu vez, estos mismos permiten seleccionar el tipo de broca adecuado y mejorar el máximo rendimiento del mismo. En cuanto la voladura y los explosivos, se revisan las variables fundamentales que ejercen una influencia sobre el resultado de un disparo y así realizar un estudio comparativo de los agentes explosivos en uso, tratando de interpretar el mecanismo de la explosión y a la vez aplicarlo a las diferentes formaciones presentes en Cerro. Finalmente, se describe la organización del sistema de seguridad y las obligaciones de este comité en la industria minera.

Aug 20, 1965

By Percy W. Bidwell

THE statisticians had defeated Germany months before she invaded Poland. With batteries of adding machines they had proved that she was suffering from serious deficiencies in critical food- stuffs and in practically all of the raw materials necessary for the conduct of modern warfare. Their calculations showed that with respect to fats, oils, wool, cotton, hides, petroleum, iron, copper and other metals, the Reich was bound to be at a great disadvantage vis-a-vis the French and British as long as the latter could keep open the lines of sea communication. The conclusion seemed obvious-"Germany can't win." The more cautious of the commentators introduced qualifications as to the length of the war and the tightness of the British and French blockade. They also made a third qualification as to the character of the struggle- whether it was to be a war of attrition or a war of movement. But since the invasion of Norway in April, there is no longer any doubt on this score. It is a war of movement-a war in which fuel, lubricants, and metals are being consumed on a scale never before seen.

Jan 1, 1940

By Ethan Steward, Kyle Perry

Underground coal mines have several dangers, one the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. These seals must be designed to withstand different pressure levels based on the potential of the atmosphere behind the seal to become explosive, either 50 psi (345 kPa) for inert atmospheres, 120 psi (827 kPa) for non-inert, and over 120 psi (827 kPa) for special cases. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at a high velocity causing them to impact and damage the mine seals. Seals damaged in this manner may no longer hold the pressure they were originally rated for and may fail during subsequent explosions or leak explosive gasses into active workings. To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals. The velocity of each projectile is measured by an infrared chronometer which can later be used to determine its impact energy. Impact effects on the seals are measured using strain gauges, LIDAR scans before and after impact, high speed cameras, and visual inspection. The focus of this paper is on the projectile generator design and initial testing.

By Shianny Cruz Vasquez

Peru is a country with a complex physiography due to the Andes uplift that expose the different ore deposits. Actually Peruvian mining produces a variety of metal commodities and has one of the world’s largest mining. It is the third-largest global producer of copper, silver, zinc and tin. Within Latin America is the largest producer of gold, zinc, tin and lead. The importance of this research was to determine the toxic elements source and the current state of surface water and groundwater all the way from the top until it empties into the Tambo River and assess their, that impact have the toxic contaminants on the environment and the human health of the surrounding Communities and provide a management and decision-making tool to prevent socioenvironmental conflicts.

Sep 1, 2017

By AIME AIME

TRADITIONALLY, the Annual New York Meetings of the A.I.M.E. cover four days, but the program is growing on each end as well as in the middle, and this year it lasted from 3 p. m., Sunday, Feb. 16, when the Education Division got under way, to 8:40 p. m., Friday the 21st, when a trainload of electrical inspectors, pro tern, got back fro111 the General Electric plant at Schenectady. The meeting has ceased to be a mere three- ring circus: on Wednesday afternoon eight sessions were being held simultaneously in the Engineering Societies Building, if one includes the Woman's Auxiliary, and according to frequent testimony one should include the W. A. as one of the most important units in Institute affairs.

Jan 1, 1936

By Z X. Zhang

In sublevel caving mines, eyebrow break usually gives rise to lower ore recovery and worse safety in the field. Eyebrow break is caused mainly by two tensile stress waves: one from the front surface of a blasting ring, and the other from the roof of the drift. In order to reduce the two waves and finally to reduce eyebrow break at Malmberget mine, we employed two methods: (1) cartridge charge, and (2) double-primers in each blasthole. The two methods were tested in one ore body called ViRi. A total of 10 rings with the cartridge charge and 25 rings with the double-primers were blasted. At the same time a total of 34 ordinary rings were blasted in the same ore body. The result shows that the eyebrow break is 3.0 m for the ordinary rings, 2.3 m for the cartridge charge rings, and 2.1 m for the double-primer rings, respectively. In addition, the ore recovery for the double-primer rings is increased by 3% on the level of ViRi930, compared with that for the ordinary rings.

Jan 1, 2011

By C. M. McKinney

This report presents analyses of crude oil from most of the fields in the United States producing 2,500 barrels per day or more. The purpose of the report is threefold : 1) To present detailed analyses of crude-oil samples from as many al possible of the important fields in the United States. On January 1, 1947, there were 340 fields producing 2,500 barrels & day or more. Analyses for 283 of these fie1ds are presented. Fifty-seven fields have been omitted because the Bureau of Mines did not have analyses or the crude oils being produced. As one sample was not representative of the promotion from several of the fields, two analyses are given for each field of this kind. (2) To compile these analyses, many of which have not been published previously in a single report. Since the publication of Bulletin 291 in 1928, there has been no report showing analyses of crude petroleum from fields throughout the United states, but a number of separate reports according to area or state have been issued. Many of these are out of print. (3) To provide a means of ready comparison of the properties of crude oils from different areas of the United states.

Jan 1, 1948

By R. D. Brown

"When elephants fight, it's the grass that gets trampled". It is becoming increasingly evident that the federal and provincial governments are awakening to the fact that their vigorous scramble for a "fair share" of mineral revenues which kicked off in 1974 has done considerable harm to the Canadian mining industry. Recent public statements made by government officials, particularly at the recently held annual convention of the Prospectors and Developers Association, would indicate that there is a general consensus in the government sector that changes must be made to the mining tax system. However, there is no evidence as yet that there is any agreement among the various governments as to what form these changes should take , who should make them , or when. It would seem to be worthwhile at this time to reflect on where the Canadian mining industry has been vis-a-vis taxes and "where it is at ". This article is based on a recent address given by R. D. Brown, of Price Waterhouse & Co., Toronto, at the annual convention of the American Institute of Mining, Metallurgical and Petroleum Engineers in Denver , Colorado.

Jan 1, 1978

By Hal J. Kelly

A picture of the ceramic industrial potential of the Pacific Northwest States is presented by reviewing the present ceramic industries, raw-material resources, and current market demands. A resume is given of the industrial plants manufacturing ceramic ware as well as available information on raw-material resources. No attempt was made to prospect for new deposits but rather to evaluate, insofar as possible, those already known. Since much of the industry is concentrated on the Pacific coast, most of the information available on resources concerns deposits in that area. Large, undeveloped districts in Montana and Idaho, however, offer promise of larger reserves of ceramic raw materials. Average annual production, some operating costs, and annual power consumption are given for each of the plants. Production and some cost figures are listed to show the limited nature of the present industry and to suggest fields open for new development.

Jan 1, 1956