Search Documents

By L. Trivino

Blast-induced damage criterion based on the peak particle velocity has worked reasonably well for estimating building damage. However, the same criterion cannot be used to estimate damage to rock and mine structures such as shaft and tunnel walls. It does not take into account the nature of seismic radiation pattern in the near-field, which is very different than what is obtained at far-off distances. To investigate this phenomenon, a systematic study has been carried out involving single-hole blasts and normal production blasts, with explosive source ranging from nearly point source charges to standard borehole sizes (6-7 m long explosive column), with charge weight varying from 0.5 kg to 30 kg. In the near-field, it is shown that, both P-wave and S-wave take a dominant position compared to the mainly surface waves measured in the far-field. These are shown to depend strongly not only on the length of the explosive column but also the way it is initiated in the borehole (i.e. direct vs. reverse initiation in the borehole) with respect to the target location. The seismic radiation patterns were recorded by high-frequency triaxial accelerometer stations grouted in the rock mass. This study describes the nature of seismic radiation in the near-field from long and short charges, the role of initiation direction and their effect on frequency with respect to sensor locations or target area of interest, and their implication in prediction of blast-induced damage in the near field.

Jan 1, 2009

By A. L. Sweetser

EXPERIENCE has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorination-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave : Fe2O3, 3.35; FeS, 1.5; MnO2, 0.75; ZnCO3, 4; Al2O3, 3.20; H2O, 0.7; SiO2 and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, .and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size-a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Sep 1, 1907

By ROBERT R. ABUOTT

(Cleveland Meeting, October, 1912.) THE practice of carbonizing steel for the purpose of case-hardening has assumed great commercial importance within the past, 10 years. Formerly, case-hardened steel was held in more or less contempt, since it. was considered a cheap substitute for tool-steel. This is no longer the case. The development of the motor-car industry, and coincidentally that of modern alloy-steels, has resulted in overcoming many difficulties formerly experienced in case-hardening. This result has been accomplished by increased knowledge regarding the analysis of the steel which would respond most readily to case-hardening, and by more careful methods of treatment of the carbonized steel. The ordinary method of carbonizing consists in packing the steel with the carbonizing-material in cast-iron boxes and placing them in a furnace at a temperature of from 1,500° to 1,900° F. for a time sufficient to give the required depth of cc case." The steel is then either quenched directly from the box, or is allowed to cool without unpacking, and finally given a single hardening-heat., or, for special work, two or three heats. During the year 1911, more than 100,000 tons of carbonizing-material was sold in the United States, at an average price of probably $55 per ton. More than 85 per cent. of this material consisted of granulated bone. Within the past four years, many manufactured compounds have been placed on the market, consisting largely of some form of carbon or carbonaceous material, with or without the addition of chemicals. Steel will absorb carbon placed in contact with it at the temperature of the atmosphere. The reaction is exceedingly slow, but. increases rapidly with increasing temperature. Below * Metallurgical Engineer, The Peerless Motor Car Co.

Dec 1, 1912

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By J. C. Scully

In June, 1965, Sanderson and scully5 reported at the Conference on Environment Sensitive Mechanical Properties of Materials at the Research Institute for Advanced Studies at Baltimore that thin foils of titanium could be prepared by chemical polishing in a mixture of 44 pct HF and 73 pct HNO3 in the volumetric ratio 2:3. The technique is simpler than that since reported by Rice and Orava. As-received annealed titanium (containing 0.8 pct Fe and 30 ppm H) in the form of sheet 0.05 cm thick is placed in the solution and moved up and down. The reaction is violent but suitable foils are obtained very easily and consistently. A typical micrograph is shown in Fig. 3. The small precipitates were not identified. Yamane and ueda6 observed many spotlike features which they referred to as small dislocation loops. While their spots may be due to the reaction of the warm foil with the air as suggested by Rice and Orava, the precipitates in Fig. 3 are also found when foils of titanium are prepared by electro-polishing at low temperatures and subsequently examined in the electron microscope without any inter- mediate warming. Furthermore, they are not a surface effect. It is necessary to add that alloys of titanium cannot be so easily thinned by the chemical polishing solution described above since it contaminates the a, phase with hydrogen and produces y hydride. These matters are described at length in a paper7 and their relevance to stress corrosion is considered elsewhere.'-* Author's Reply The authors are grateful to Dr. Scully for bringing to our attention his hitherto unpublished technique for thinning unalloyed titanium, and deeply regret the unintended apparent duplication. The chemical thinning solution (7 parts HNO3 and 3 parts HF, by volume) reported by us is the same as that with which, for some period in the past, we had experienced success in the preparation of foils from single and polycrystalline niobium. Its subsequent effective application to titanium was a logical step, which, clearly independently of Scully, was conceived by Mr. Rice, to whom full credit is due. A few comments are warranted concerning some of the details of the preceding Discussion. It is evident to the discerning reader that the two thinning techniques under consideration are chemically almost identical, and in that sense are equally "simple". The chemical aspect is, of course, the one of primary importance in both communications. Thereafter, the relative simplicity is dictated by the mechanics of the actual thinning operation selected by the individual investigator. Our standard dimpling, or dishing, procedure was chosen with a view toward providing, for the electron transparent areas of the sample, the maximum protection from extraneous deformation during handling. That the long, straight dislocations visible in Scully's electron micrograph of a seemingly recovered structure closely resemble handling dislocations would tend to indicate the merit of our adopted technique. Features similar to those which Scully has attributed to precipitates, without any apparent diffraction contrast confirmation, were not observed in any of our clean foils taken from annealed or deformed specimens. This was admittedly somewhat surprising since the 3700 ppm (nominal) Fe in the A-70 commercial-grade titanium examined should have given rise to TiFe precipitates. Presumably these existed but were un-resolvable. Curiously, Scully's "precipitate1' density is fairly high although the iron content quoted was less than one-fourth of that in our material. One is forced to conclude from the evidence that prior thermal and mechanical treatments are responsible for the two different types of structure observed.

Jan 1, 1968

Engineering programs usually do not provide sufficient opportunities for students to develop written communication skills. The responsibility for developing those skills is frequently delegated to the humanities faculty, who in a single technical writing course are supposed to transform engineering students into proficient communicators. A general template which was developed for report writing in our senior level capstone design courses is discussed. Students have improved their writing skills by using the template. The writing assignments have provided the students the opportunity to write and revise more technical reports that communicate their design.

Jan 1, 1995

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By Jake Gibson

"As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action toward decreasing greenhouse gas (GHG) and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel, accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery-powered ac systems and diesel-fired heaters, going noidle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, standalone mobile equipment HVAC.The history of GHGs and climate changeIn 1896, Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960s, Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Fig.1).In 1988, the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgment of a rising global annual temperature. The IPCC consists of more than 2,500 scientific and technical experts from more than 60 countries. Because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998, requiring all participating countries to reduce their GHG emissions by at least 5 percent from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States). In 2002, the Bush administration announced a policy for climate change relying on domestic, voluntary actions to reduce the "greenhouse gas intensity" of the United States economy by 18 percent by 2012. The U.S. still attends the Kyoto conference of parties (COPs) but does not participate in negotiations, as it is not bound by its terms."

Jan 1, 2014

By S. E. Bretherton

Discussion of the paper of S. E. BRETHERTON, presented at. the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1595 to1599. ANTON EILERS, Brooklyn, N. Y. (communication to the Secretary*). While the advantages in the use of high-line siliceous slags in lead smelting which Mr. Bretherton discusses in this paper are obvious under certain economical conditions, he gives me credit for the introduction of such slags when it does not belong to me. It is true I did considerable experimental work, off and on, for the purpose of finding such slags, while at the Germania in 1877 and 1878, but I did not have occasion to introduce any such slags for regular work, because I had no ores which fitted the economical conditions for using high silica and high lime, except in isolated cases for very brief periods. On the contrary, the ores I had to treat were mostly very ferruginous and very low in silica, so that, economically, I was compelled to run nearly always on slags, which allowed me to use the abundant flux I had without cost. It was August Raht who first had occasion to establish and use for long periods a slag high in silica and line, and low in iron. This was when he was confronted with the task of smelting the. Horn-Silver ores at the smelting works at Franklin, Utah, with as little expenditure for fluxing material as possible. I was at that time in Leadville, Col., where, in the new works I had built, the Billings and Eilers smelters, I had occasion to use profitably many slags, but never anything as high in the earthy bases and in silica as Mr. Raht had to use.

Jan 12, 1915

By George R. Mansfield

Interest in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lakeland, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.l At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern producers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This information has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,² some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,³ of the Tennessee Division of Geology. Prof. J. Stewart Williams,* of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered. Technologic advances in the phosphate industry must be credited with a large share in the expansion of reserves by making available for

Jan 1, 1942

By George R. Mansfield

Interest in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lakeland, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.l At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern producers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This information has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,² some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,³ of the Tennessee Division of Geology. Prof. J. Stewart Williams,* of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered. Technologic advances in the phosphate industry must be credited with a large share in the expansion of reserves by making available for

Jan 1, 1942

By G. S. Victorovich

Technical progress in primary smelting has changed the face of the copper industry in the years since the Second World War. Much of this change has resulted from a wide acceptance of flash smelting technology. In addition, research has been directed toward devising converting processes to replace conventional Peirce-Smith converting technology. One major thrust has involved a revival of the old " ", idea of oxygen flash converting of comminuted mattes. This paper reviews the 60-year history of flash converting. Particular attention is paid to Inco's investigations into the processing of white metal containing significant amounts of nickel and, in some cases, iron. Thermodynamic analysis and laboratory experimental results are presented which throw light on the behaviour of nickel and other salient features of flash converting. The possible role of oxygen flash converting in the copper pyrometallurgy of the future is briefly discussed vis-a-vis direct production of copper.

Jan 1, 1993

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

The annual general meeting of the Branch was held at the St. Helena Club on Thursday, August 21, 1969. Mr J. G. Kirchner (Chairman) was in the Chair. Also present were Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Nine Members: Messrs N. A. Honnet, W. R. Lawrie, J. N. Saunders, D. D. Waterman (Committee Members), M. G. Cullen, G. C. P. Labuschagne, H. A. G. Slater, I. G. Thomas, T. Zadkin and Nine Associate Members: Messrs R. Campbell, D. E. Couperthwaite, T. M. Espach, J. M. Ferguson, G. W. Futcher, A. G. C. Merson, E. R. Penny, R. B. Sutherland, J. W. van den Munckhof and One Visitor: Mr D. J. McLaren. The Chairman declared the meeting open and, on behalf of the Branch, thanked the President for coming from Johannesburg to attend. MINUTES OF THE PREVIOUSGENERALMEETING As the Minutes of the General Meeting held on June 18, 1969 had not yet been published in the Journal, the Chairman moved that their adoption and the discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. CHAIRMAN'S ANNUAL REPORT 1968/69 At Mr Kirchner's request, Mr. R. C. J. Goode took the Chair during the presentation of the Chairman's Annual Report. (This report was published in the August 1969 issue of the Journal.) OFFICE BEARERS AND COMMITTEE MEMBERS FOR THE YEAR 1969/70 The Chairman announced that the outgoing Committee had elected the following office bearers for the coming year: Chairman: N. A. Honnet; Vice-Chairman: J. N. Saunders; Immediate Past Chairman: J. G. Kirchner. The Chairman then read a letter from the scrutineers reporting that the following had been elected to the Committee: M. S. Grobler, W. R. Lawrie, L. O. W. Leimer, A. T. Lewis, R. S. Pearson, T. Zadkin. The Chairman thanked the scrutineers for their services, and congratulated Messrs Lawrie, Leimer and Zadkin on their re-election and Messrs Grobler, Lewis and Pearson on their election to the Committee. The Chairman announced that he had heard, with regret, that Mr. T. Zadkin would be leaving the O.F.S. at the end of August, 1969. Mr Zadkin had served on the Committee continuously since the inception of the O.F.S. Branch and records showed that he had only failed to attend three General Meetings in over nine years. The Chairman expressed the gratitude of the Branch for Mr Zadkin's invaluable services to the Institute, congratulated him on his well earned promotion and wished him well in his new position. INDUCTION OF CHAIRMAN The Chairman introduced Mr N. A. Honnet to the meeting by briefly outlining his past career and, after congratulating him on his election, called upon him to take the Chair. In congratulating the out-going Chairman on a very successful term of office, Mr Honnet said that due to the absence of many Committee Members for a large portion of the year Mr Kirchner had carried a heavy burden, and he moved a vote of thanks and appreciation for Mr Kirchner's efforts. This was carried unanimously. GENERAL BUSINESS There were no points raised under this heading. MINING AND METALLURGICAL CONGRESS The Chairman called on Mr W. R. Lawrie to give his talk on aspects of the Mining and Metallurgical Congress recently held in Britain. This presentation was illustrated with photographic slides and proved of great interest to Members. Mr D. D. Waterman proposed a vote of thanks to Mr Lawrie and the Chairman then asked Mr R. C. J. Goode to contribute to Mr Lawrie's address. Mr Goode thanked Mr Kirchner for his efforts during his very successful term of office and congratulated the in-coming Chairman and Vice-Chairman on their election. He then gave a brief talk on aspects of the Congress not dealt with in Mr Lawrie's address. These included the industry's requirements of graduates, the necessity of their rapid advancement and the desirability of sending such young men to attend future Congresses. Mr Goode announced that two symposiums will be sponsored by the Institute next year, one on Tunnelling and the other on Open Cast Workings.

By A. L. Sweetser

Experience has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorina-tion-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave: Fe,O,, 3.35; FeS, 1.5; MnO,, 0.75; ZuCO,, 4; A1,0,, 3.20; H,O, 0.7 ; SiO, and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size—a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Jan 1, 1908

By Angus D. Campbell

"IntroductionThe subject assigned to me tonight gives unlimited scope. The material available is so voluminous and leads into so many ramifications, and the memories of the Camp are so vivid and treasured, that it is difficult to decide just what to use. Then, too, the geologists are the story-tellers of our tribe - I am only a hard rock miner.Members of the Cobalt Branch and Cobalters everywhere will agree without question that this Cobalt camp has been the greatest of all influences on Canadian mining. To those who do not know Cobalt, our opinion may seem prejudiced and our statement exaggerated.Be that as it may, discussion on this subject can be profitable, since it is worthwhile now and then to think on 'whence we came' and 'where we are going'.In the revival of interest in the Cobalt camp, we hope our guests may feel some of the old Cobalt Spirit, which has become the Spirit of the North.Visitors may even, while here, catch a glimpse of that whimsical little guardian spirit of the camp - the original goblin, the Kobold - for which Cobalt was named.While Kobold brings that good luck which plays so important a part in mining, he can have his evil moments, as in his original German home. There, when he made the silver disappear from their good ore, they cursed the grey ore, calling it Kobold.Although this little goblin bas frequently upset our best mining plans and geological calculations, be has played the game as well. He placed •some silver on the surface, and when he hid ~t at depth he left dues .for its finding. He has rewarded many who sought his treasure and is still rewarding those who have persevered and had faith in him. t:lis influence and that of Cobalt camp has probably had a greater influence on your work and your mining areas than you realize"

Jan 1, 1950

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer

In an attempt to reduce the potential for fish mortality during the explosive demolition of Locks and Dam 26, Mississippi River, the U.S. Army Corps of Engineers, St. Louis District explored the use of a bubble curtain to reduce the fish kill radius of underwater explosions. Bubble curtains are walls of bubbles rising from a bottom-resting bubbler manifold supplied with compressed air. Demolition engineers have long been aware of the attenuating properties of air bubbles in water. As such, air curtains have been routinely used to protect underwater structures from damage by underwater explosive shock waves. However, their use in protecting aquatic resources during full-scale explosive demolition projects was untested.

Jan 1, 1997

By David Nicholls

?Overview of New Afton ?Reserves and Resources ?Geology and Mineralization ?Exploration ?Capital Project Development to Date ?Mine Development ?Processing ?Construction ?LOM ?Health, Safety, Environment and Social Responsibility Overview of New Afton ?Fully owned by New Gold Inc ?Large gold-copper porphyry deposit, amenable to block cave mining, production commencing in 2012 -1 million ounce gold reserve -1 billion pound copper reserve -Estimated 13 year mine life ?Low operating cost ?Estimated capital expenditure requirements -Spend to date ?US$200million -Remaining to be spent ?US$400milllion ?Robust economics ?Excellent location and infrastructure ?Significant cash flow contributor for the Company

May 1, 2010

By G. Mihaylov

The basic principles of systems analysis are presented. A model has been designed to determine the location of the Main opening in the presence of three or more stock orebodies. The necessary condition is to find a location for the Collection point which is an essential element in opening up each orebody (stock). The model takes into account the total transportation costs from each orebody to the collection point. Three variants are considered provided that the orefield is divided into two levels at least: - a collection point is designed at every level; - a collection point is designed at the lowest level, i.e. where the so-called concentration level is formed; - the collection point is located at a point between the planes of the two levels; The effect of the depth of mining and mine output on determining the method of opening up the orefield has been analyzed by considering a vertical and/or an inclined shaft. A function has been constructed which allows for investigating in both a static and dynamic regime the capital costs for constructing the whole complex including the shaft. The character of the function does not allow finding the global limits. Therefore, it is of particular importance to specify the limiting conditions. In this case these are the flow capacity of development openings and the shaft. The basic groups of cost and natural indicators for assessing and selecting an optimal technological solution have been systematized. The combined analysis of the two approaches to finding the location of the Main opening and determining the mining method enables us to determine when an inclined shaft is best, and the depth at which opening by a vertical shaft has no alternative. Thus, a transition area is formed for which the selection of an optimal technological solution requires an analysis similar to that proposed in this paper. Conclusions are finally drawn which serve as a basis for determining the areas of application of each opening, including the use of a combined scheme of mine opening. The approach presented can be used in both investigating the possibilities for opening up new orefields and reconstructing existing ones in cases when the mining operations go deeper.

Aug 1, 2013