Search Documents

By I. G. L. Sinclair

The Selbaie deposit is located in northern Quebec. It is comprised of three distinct, but genetically related, Cu-Zn-Ag ore bodies which also contain economically significant amounts of Au. The deposits are Archean in age and volcanogenic in origin. At Selbaie, ore microscopy has been employed to aid in planning of ore beneficiation methods and to monitor the ongoing performance of the concentrator. Examples of both types of study are described. Early in the life of the mine, excessive amounts of Zn appearing were found to be appearing in the Cu concentrate. Microscopic examination of concentrates showed that this was being caused by the presence of coatings of supergene chalcocite on sphalerite grains. Fine coatings of supergene galena and chalcopyrite were also observed on some sphalerite grains. The presence of Ag and Au in the ores makes an important contribution to the revenue of the mine. The various modes of occurrence and mineralogical relationship of these two metals are described and discussed. Monitoring of the ongoing concentrating process at selbaie is done by qua-litative and quantitative examination of products collected at various points along the circuit. Causes of such problems as excessive loss of metals to the tailings or inefficient recovery of individual metals, can often be identified and possible solutions proposed.

Jan 1, 1989

By Ralph Hayden

PAGE I. IntRoduction........239 II. Definition of Anaconda SLime....240 III. The Source of Slime......240 Remodeled Flow Sheet......240 Old Plow Sheet,.......242 IV. ConStitution of Slimes......243 Chemical........243 Physical.........243 V. The Slime Problem.......247 VI. THe Experimental Slime Plant....248 VII. Slime Thickeners. ETc .......249 Slime Ponds........249 Tanks.........249 Comparative Efficiency of Open and Baffle Tanks .260 Callow Tanks........252 Kuchs-Laist Centrifugal Separator....253 Garred Filter........256 Dorr Continuous Thickener.....256 VIII. Concentrators........257 Round Table........558 Peck Centrifugal Concentrator....259 Competitive Tests.......260 Twenty-Deck Round Table..... 260 Slime Feed Distributor......261 IX. ConcluSion.........262 I. Introduction. In the wet concentration of ores there is always a certain amount of very fine material with which to contend. and which invariably carries such quantities of value that the treatment of it is worth while. commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely. the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 1, 1914

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By B. M. Harra, O&apos

Zinc smelting is frequently termed a backward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, low-unit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pounds of ore. The diameter of the retort is limited by the time required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, or producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser attached to one end of the retort, where it condenses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls and of the ore charge itself, the heat efficiency even of the most modern regenerative furnaces is only about 12 per cent. The retorts have a short life, 30 to 60 days, at the high temperature required; zinc

Jan 1, 1923

By Anthony Anable

HOOVER DAM, rapidly nearing completion in the Black Canyon of the Colorado River at Boulder City, Nev., taxes the superlatives of the vocabulary to describe. For by all odds, it is the largest construction project of its type ever essayed by man and the plants providing the essential materials of construction are also in a class by themselves not only in size but in advanced design, mechanization, and accurate control. Picture, if you will, the great aggregate plant, as it is called, situated about 4 mi. upstream from the site of

Jan 1, 1934

By AIME AIME

THE following brief description of the main features of the, engineering work was prepared for the use of members of the American Society of Civil Engineers and members of the American Institute of Mining Engineers on the occasion of their visits to the tunnels at the time-of their respective. annual meetings in New York, January and February, 1905. DESCRIPTION. Those portions. of the Pennsylvania Extension into Manhattan and Long Island, lying east of the Terminal Station and west of the East River, have been designated as the " Manhattan ?Cross-town:. Tunnels." They traverse a section of the city second in importance only to the financial district, and one that includes the larger hotels, retail shops and theaters and the residences of many of the best known citizens. Section "D," consisting of twin tunnels for west-bound express and local passenger traffic, lies under Thirty-third Street from a point 400 ft. west of the west line of Sixth Avenue, eastward to the river shaft, situated in the block between Thirty-third and Thirty-fourth Streets east of First Avenue. Beginning at the east end, the tunnels are in separate excavations, leading westward from the subaqueous tubes, on a curve of large radius, gradually closing together until it is found more appropriate to drive them in a single excavation. At a point just west of Second Avenue they reach the tangent, aid from there westward lie directly under Thirty-third Street. At a point about 180 ft. west of the west line of Sixth Avenue, the center concrete-wall between the twin tunnels is omitted, and the excavation somewhat widened to make room for a third storage-track, and the tunnel continues to tile station portal in three-track section. Here reprinted through the courtesy of The United Engineering and Contracting Co. The half-tone blocks used for the illustration of this paper have been kindly supplied by the Chasmer-Winchell Press of New York, Pittsburgh and Cleveland.

Mar 1, 1908

By Angus D. Campbell

Introduction In the Twentieth Annual Report of the Mcintyre Porcupine Mines, Limited, for the year ending March 31st, 1932, the General Manager, Mr. R. J. Ennis, said: "During the period under review, the plans outlined in last year's report have been completed, and all operations have been centralized in the new plant adjacent to No. 11 shaft. The new mill went into operation on May 27th and attained its rated capacity of 2,000 tons per day on November 15th. The new shops, warehouse, change-house, and general offices were occupied on December 1st, consummating the change from the old to the new plant ... "Silicosis is now definitely recognized as an industrial disease, and progresses rapidly when associated with tuberculosis. In an effort to combat its prevalence and progress, the new change-house was designed to build up the men's resistance to this and other forms of disease. It provides for a complete change from underground to street clothing, with a shower bath and solarium treatment in the interval. 'Unfortunately, in almost every goldmine, a very small percentage of the work-men are not adverse to taking some of the high-grade ore for their own purpose. This, in turn, tends to cast suspicion upon the honourable as well as the dishonorable employees. The new change-house routine discourages this practice and eliminates unjust suspicion, to the satisfaction of all concerned with the Company's operations".

Jan 1, 1933

By S. H. Ash

THE ANTHRACITE region of Pennsylvania contains over nine-tenths of the total anthracite deposits of North America and produces all but an insignificant proportion of the total output of anthracite in the Nation. The whole economy of the northeastern section of the United States depends, to a large extent, on the mining of Pennsylvania anthracite, which is shipped to New Jersey, New York, and New England and is a principal source of energy and heat for that entire region. The responsibility of the Federal Government for developing an engineering method that will prevent inundation of the Pennsylvania anthracite mines and keep them in operation has long been recognized. To obtain a reliable picture of the anthracite-mine-water problem and to solve that problem, it is necessary to have factual data on the volume and the quality and character of the mine water handled by the pumping plants in the anthracite region, as well as the kinds of pumps utilized and problems concerning their operation.

Jan 1, 1953

By Craig Haase

A. Introduction

Jan 1, 2003

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By Walter J. Mead

By American tradition, if not by rational decision, publicly owned natural resources have been transferred to private industry for processing. The process of transfer requires specific determination of the price which the patentee, buyer, or lessee must pay to the government in exchange for the right to develop a resource, and selection of the patentee, buyer, or lessee from among several possible contestants. Pricing of natural resources owned by the government presents a set of problems quite different from ordinary commodity pricing. Natural resources in situ are not homogeneous commodities. Within any class of natural resources, specific leasable parcels will differ in value by reason of location and accessibility, as well as quality and quantity. Thus, there is no "going price;" every lease within a specific resource class will have a different value. To complicate further the pricing and buyer selection problems, competition may not be reliable. Natural-resource markets are characterized by oligopsony conditions. In a significant number of cases, as will be shown later, there has been only one bidder for a given lease, and in most lease sales the number of bidders is equal to or less than three. As a further complication, there is great uncertainty regarding the value of specific resources, even among the best-informed buyers, as well as within the leasing agency. In some instances, particularly with regard to oil and gas resources, there may be uncertainty about the presence of resources, as well as the quantity and quality of any resources contained in the tract offered for lease. In other cases, such as oil shale and some deep ocean minerals where new technologies are involved, the presence of the resource is clearly established. There may be a relatively high degree of knowledge about the quantity and quality of the resource, but there is great uncertainty concerning the cost of production. These problems in total make it difficult for the leasing agency to appraise accurately the resource to be leased, as well as for the potential bidder to calculate a bid price that will yield him a normal profit. The pricing goal of the federal government as the seller or lessee may be to capture the economic rent; that is, the price of a resource might equal its discounted present value. A required price substantially above this amount would either generate no bids, or, in the long run, would bankrupt the buyer. A price below this amount is a disguised subsidy to the lessee. A subsidy to mineral lessees, as to any other economic interest group, as a minimum should be justified by a clear showing of net external benefits from the economic activity. In the case of timber sales by the U.S. Forest Service, the Forest Service Handbook asserts that "the aim in national forest stumpage appraisal is to determine market value,"8 and "market value" is equated to "fair market value." Regarding minerals, there is no reference in legislation or regula-

Jan 1, 1976

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By L. Schernikau, W. H. Smith

Oil, coal, and gas account for approximately 80% of global primary energy, but only a portion of total airborne CO2 eq (approx. 35% at GWP20 to 65% at GWP100), even though they account for 95% of total measured CO2 emissions. The benefits of these energy sources, as well as their related costs, are not all incorporated in current energy policy discussions. Global greenhouse gas policies must include documented changes in measured airborne CO2 eq to avoid spending large amounts of public funds on ineffective or sub-optimal policies. The authors examined airborne CO2, which is less than half of emitted CO2, as well as reported CH4 emissions and the global warming potential of CH4 as published by the IPCC for coal and natural gas. The surprising conclusion is that surfaced-mined coal appears ‘better for the climate’ than the average natural gas, and all coal appears beneficial over LNG. Therefore, current CO2-only reduction policies and CO2 taxes are leading to unintended consequences and the switch from coal to natural gas, especially LNG, will not have the desired impact of reducing predicted future global warming; in fact, quite the contrary. A large portion of anthropogenic global warming is attributed by the IPCC and IEA to CH4, but it must be noted that CH4 emissions from natural sources and from agriculture account for approximately 40% and 25% of annual global CH4 emissions respectively. Energy accounts for about 20% of documented CH4 emissions. CO2 contributes only approximately 35% of annual airborne anthropogenic GHG emissions after accounting for CH4, over a 20-year horizon. At a 100-year horizon, the contribution of CO2 increases to approximately 60%. Energy policies that do not consider all GHG emissions along the entire value chain will lead to undesired economic and environmental distortions. All carbon taxation and CO2 pricing schemes are incorrect and need to be revised. At IPCC’s GWP20 an approximately 2%1 higher loss of CH4 across the value chain prior to combustion of natural gas versus coal will lead to ‘climate parity’ of coal with natural gas. According to public data, natural gas value chains have high CH4 and undocumented CO2 losses. On a global average, using only IEA-documented CH4 data, natural gas emits approximately 15% more CO2 eq than surface-mined coal, over a 20-year horizon. This difference will increase as the use of shale gas and LNG expands. Investors should support all energy systems in a manner that avoids an energy crisis, including intermittent renewable energy systems where they make sense. If CO2 emissions need to be reduced, one of the most effective ways would be to install ultra-supercritical power plants with CCUS technology. However, the undisputed benefits of increased CO2 concentrations in the atmosphere because of its promotion of photosynthesis and plant growth effects (fertilization) need to be considered in energy policy decisions as well. The authors suggest that future research and development should concentrate on reducing net emissions from fossil fuel power plants and providing cost-effective and reliable new conventional power generation capacity, utilizing clean coal and clean natural gas technology.

Mar 2, 2022

By Christopher J. Farrow

This paper describes the grinding circuits installed at two remote sites in northern Canada. One is Cominco's Polaris Project at Little Cornwallis Island; a barge-mounted lead/zinc concentrator. The other is Echo Bay Mines' Lupin Project at Contwoyto Lake, 400 km northeast of Yellowknife, a gold mine, all components of which had to be flown to the site. Logistics and considerations of operating and maintenance presented challenges which were met by innovative design. The evolution of the grinding circuits is discussed. Both plants are operating at design throughput.

Jan 1, 1983

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By Guo Xueyi

The method of Substance Flow Analysis (abbreviated as SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level. In this work the flow of lead in China, 2006, was traced within the STAF model, and the situation of production, consumption and recycling of lead resources in China were introduced. The SFA is performed on lead flows during its one year life cycle in detail. As one of the biggest producer and consumer of lead in the world, China is facing a problem depletion of lead resources. How to increase the resource efficiency is a significant issue for lead industry of China. Based on the result, several suggestions were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of lead industry in China.

Jan 1, 2009

By D. Newman

An underground limestone quarry, developed in the 1940's, transitioned from a surface quarry to an underground room-and-pillar operation. The quarry expanded to a second underground level when the reserves on the first level reached the property boundaries. The historical basis for the sill pillar thickness between the first and second level, pillar dimensions, and mining height was lost during the course of several changes in ownership. When reserves on the second level reached a five-year life, and plans were initiated for a third level, quarry management embarked upon a thorough evaluation of i. current ground control practices for the support of the immediate roof, ii. roof support in the declines between the surface, Level 1, and Level II, iii. pillar centers and pillar safety factors, iv. pillar alignment between levels, v. mining height within a level, and vi. the locations of declines to access future reserves on level three. The evaluation began with detailed mapping of the location and orientation of calcite veins, joints, fractures, and ground conditions in the immediate roof of Level II. The orientation and location of calcite veins, joints, and fractures on Level II were compared with similar mapping on Level 1, completed in the 1970's to establish whether these features were continuous and would be expected to affect conditions on Level III. Rock strength, physical properties, and fracture spacing were obtained from two (2) diamond core holes drilled from Level I to Level II and two (2) holes drilled from Level II to define the vertical extent of future reserves on Level III. The effort to characterize geological conditions was expanded to a rock mechanics investigation of the: i. performance of the current roof support, ii. optimization of roof and rib scaling, iii. calculation of safety factors for 416 pillars on Level II, iv. evaluation of future pillar centers and mining height within a level based upon pillar strength and pillar geometry, v. development of beam safety factors for the immediate roof on Level II, vi. identification of the most suitable strata for the roof in the future level three, and vii. use of LAMODEL to develop a large numerical model of overburden, inter-level, and total stress on the pillars in levels one and Level II with a stress "footprint" on the proposed level three. The characterization of engineering parameters and geological conditions resulted in changes to the: ? active operations in Level II regarding scaling ? equipment and scaling practices, ? pillar centers, ? mining height, ? raising the immediate roof horizon to avoid ? laminated strata in the current roof, and ? a change in rock bolts from a friction based system ? to active tensioned rebar. The planning and design of level three is ongoing and relies heavily upon the geological and engineering investigations conducted during the past year and one-half.

Jan 1, 2001

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By C. Q. Payne

(New York Meeting, February, 1912.) THE art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates back to the year 1806, when they were employed in Cornwall, their principal development has taken place during the last 30 years. To Stephen R. Krom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contribution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the movable roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springs, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to exercise new functions. In developing crushing-machinery for his Portland cement works, Mr. Edison constructed ? giant " rolls, having a diameter of 6 ft. and a length of. face of 7 ft.

Jun 1, 1912