Search Documents

By William Hutton Blauvelt

The type of gas producer in which the ashes are fluxed and run off as slag was among the very earliest made. Ebelmen built the first one in 1840 at Audincourt, France, only a year after the installation of the first gas producer of which we have record. Charcoal was used as the fuel, with blast-furnace slag and clay as flux. My interest in this type of producer began when as a boy I saw the fluxing producer at Chester, N. J., which was invented by W. J. Taylor, and described by him in 1881.' This producer was invented independently by Mr. Taylor to meet the difficulties he experienced in making producer gas for roasting sulphurous iron ores. It will be of interest to review briefly his description of his producer. It was built like a small blast furnace, having a hearth 24 in. in diameter and 24 in. high. The bosh angle was 25' from the vertical; the diameter at the bosh 4 ft. and at the top 3 ft.; the total height 12 ft. The producer contained one water-cooled tuyere 12 in. above the bottom, with a 1.5-in. nozzle. Depth of the coal above the tuyere, 6 ft. Mr. Taylor mixed the coal with from 30 to 40 per cent. of basic blast-furnace slag to flux the ash. Occasionally some limestone was also used, but never limestone alone, as the use of the furnace cinder gave a larger volume of slag and made it easier to maintain a proper fluidity. The producer was blown with a small Weimer blowing engine, delivering 300 ft. of air per minute, at from 1 to 1.5 lb. pressure. The slag was tapped every 2 hr. and was black and glassy in appearance. Broken or egg size anthracite was used. The fine sizes of anthracite could not be made to work. Mr. Taylor expressed the belief that bituminous coal could be used if not too fine, but no experiments were made with this coal. Runs were made of four weeks' duration, with no stops or changes. Mr. Taylor reported the following advantages: 1. Excellent gas, very uniform in quality. The high fuel bed permitted no air to pass unconsumed, and the gas was almost entirely free from carbonic acid.

Jan 1, 1914

By Earl S. Bardwell

In his paper entitled, Development of Hindered-Settling Apparatus, Dr. Richards has related the history of the development of the hin-dered-settling classifier and given illustrations of the several types of this apparatus which he has designed.' An earlier paper,2 Close Sizing Before Jigging, shows the nature of the hindered-settling phenomenon and the results which it produces. In the first-mentioned paper Dr. Richards describes the method of getting hindered settling and shows the relation that the constriction bears to the classifier. The question of proper ratios between the area of the sorting column and the area of the constriction opening Dr. Richards leaves open, aside from certain statements as to the ratios which have been found to give good results in practice. While working with a hindered-settling classifier of the type now in use at the Boston & Montana Reduction Plant of the Anaconda Copper Mining Co. a number of interesting facts were brought out which have thrown considerable light on the question of proper ratio between the area of the sorting column and the area of the constriction and which will be made the subject of this paper. Free and Hindered Settling.—If a mineral particle be dropped into a vessel containing still water, the particle will sink in accordance with the laws of free settling in water, which are as follows: 1. Of two grains having the same specific gravity but differing in size, the larger will settle in still water at the greater velocity. 2. Of two grains having the same size but differing in specific gravity, the heavier grain will settle at the greater velocity. From these laws it becomes evident that the velocity of settling depends primarily on the specific gravity and the size of the mineral grain. The fracture of the mineral may exert a very considerable

Jan 1, 1914

By B. G. Klugh

The present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglomerating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the application of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with ma-terials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited time allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace. The following microphotographs are arranged in the order of the degree of complete fusion to which the mass in question has been subjected, in effectively binding the particles together. A very notable fact here clearly demonstrated is that the degree of fusion to which the material has been subjected is inversely proportional to the reducibility of the product. The characteristic of the material under consideration to which reducibility is almost universally attributed call be progressively traced in the following arrangement, through the identity of the obvious microscopic constituent. Furthermore, the degree of fusion to which a bod? has been subjected is recorded in the presence of resultant products of fusion in that body. Such readjustment is generally apparent

Jan 1, 1914

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By W. R. Shimer, F. O. Kichline

The investigation herein described was carried out for the purpose of studying, both by chemical and metallographical means, the extent of over-oxidation of steel that can be accomplished by excessive overblowing in a Bessemer converter. 111 addition there are appended some results of basic open-hearth and crucible steels. Remarks on Chemical Methods. The test block used was hemispherical in shape, 4.5 in. in diameter and 2 in. thick. Drillings for analysis were obtained by drilling through the entire solid part of the block, carefully avoiding all cracks and blow-holes and mixing these drillings thoroughly. Drillinga were carefully examined for scale and the finest were gone over with a microscope to be sure all scale from whatever source had been removed. Oxygen was determined by the well-known method of Ledebur, modified according to Cushman,1 with, however, the removal of the preheating tube, which was found unnecessary. This method has been found to give concordant results. Blanks run from 0.0003 to 0.0006 g. Duplicate determinations varied not more than 0.001 to 0.003 per cent. It seems to be generally supposed that the hydrogen method gives only that oxygen which is combined with iron. Whether this be true or not, the content of oxygen existing as iron oxide no doubt predominates sufficiently, so that the result obtained is sufficient to indicate whether the steel is over-oxidized or not. We are well aware that the oxides of manganese and chromium, when existing alone, are not reduced by hydrogen at a red heat. To learn of their action in steel the following work was carried out: A sample of ferro-manganese and of ferro-chrome were each exposed

Jan 1, 1914

Jan 1, 1914

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By Woolsey McA. Johnson

In metallurgical circles it is known widely, but somewhat vaguely, that the ease of reduction of metallic oxides depends largely on the way they hare been prepared. It is likewise known that different forms of carbon have different and greatly varying reducing powers. It is the purpose of this paper to show somewhat more definitely and scientifically these facts. Some years ago the writer published an account of pyrometric determinations of the reduction temperature of zinc oxides variously prepared and of several kinds.' In said paper it was shown that the temperature at which zinc oxide evolves zinc according to the equa-tion ZnO + C = Zn + CO depends upon the nature of the two reacting bodies. The determina-tions had a range of accuracy of from 2° to 6°C., whereas differences were found to amount to an extreme of 90' C. So the differences are real ones and must have a definite cause. The equation of boiling water, (H2O)4 D 4 (H2O) has a fixed temperature for equilibrium of 100° C. at 760 mm. pressure. In general, all equations reacting in the liquid or the gaseous phase have well-defined constant physical conditions which govern the equilibrium point and reaction velocities. In a reaction where we have one or more solid phases, the tempera ture conditions requisite for the unbalancing of the stable system are found to vary. These variations are due to the fact that in a solid there is a very complex molecule and it is not a question solely of the tearing away of two interlocked atoms, but also of the destruction of a complex molecule containing hundreds, or possibly thousands, of smaller molecules. In other words, there are two forces to be overcome: a certain

Jan 1, 1914

By Howland Bancroft

This article is not presented as a treatise on tin mines and mining in Bolivia. It deals primarily with the tin situation, and but fragmentary information is given regarding individual properties, generalizations being necessary in so short an article. Data on general subjects related to tin mining in Bolivia are necessarily abbreviated and very incomplete. It is believed that the references to be found in this article will help those interested to a more thorough understanding of the general conditions extant in Bolivia. Bolivia produces from one-fifth to one-fourth of the world's supply of tin. The United States consumes about one-half of the world's supply and produces practically none. Tin ore is not reduced in the United States. These facts are not generally appreciated by American mining men. Many conflicting data have been published regarding tin in Bolivia. The Transactions of the Institute contain practically no mention of this subject.' I have made a study of mines and mining conditions in the west coast republics of South America and have been particularly impressed by the possibilities of the Bolivian field.= In consequence the thought seems justified that the present meeting would present a fitting occasion to bring the tin situation in Bolivia to the attention of American mining men.

Jan 1, 1914

By A. Eilers

A number of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks. One of these has furnished me the following table of recoveries from given amounts of blister. I publish this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities. GarFIeld, Utah :—The blister copper comes principally from the Bingham porphyry copper mines. Steptoe, Nev. :—All the blister copper is produced from the Nevada Consolidated mines. (Also porphyry deposits.) Omaha, Neb. :—Blister copper comes principally from concentrated copper-lead mattes shipped from the different lead-silver plants of the Rocky Mountain region to the converters at the Omaha lead refinery. Mountain, Cal. :—Ores occur in connection with diorite (?).

Jan 1, 1914

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By E. P. Mathewson

In a discussion of a paper on The Basic Process as Applied to Copper Smelting, by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1891,' Prof. W. C. Roberts-Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Manhks process would afford anything like the service which it had been shown to render in the metallurgy of iron. Claude Vautin stated that he had experimented for over two years. with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned,Hermann Keller, Superintendent of the Parrot smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were too small. A short time afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., and at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines. Fig. 1 is a view of the first tilting furnace casting copper. It was made from an old Brueckner roasting cylinder. Fig. 2 shows an elevation and vertical and horizontal longitudinal sections of the second tilting furnace, built in 1897.

Jan 1, 1914

By Robert Franke

In view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in. For the ore of this mine, a moderately hard but very fissile schist,

Jan 1, 1914

Jan 1, 1914

By H. M. Chance

Adequate treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has been termed " intrinsic value " must be limited to materials that are essential to existence—air, water, food. But " intriusic value" cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed " intrinsic values." For many reasons it might be well, while assenting to the fact that any material may be intrinsically valuable, to abandon the use of the term " intrinsic value." One of these reasons is the tendency to confuse the idea of intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent. Intrinsic value must from its nature be permanent and unchangeable. Possibly for present purposes the value of any material may be considered as having a dual origin: First, that due to economic

Jan 1, 1914

By J. J. Crowe, G. K. Burgess

PAGE, Theories of Allotropy of Iron........... 667 Previous Determinations of A2 and A3 in Iron........ 668 Critical Ranges as Determined by Expansion........ 669 Critical Ranges by Thermoelectric Observations........ Critical Ranges in Terms of Crystalline Structure....... 670 Critical Ranges as Detected by Mechanical Methods...... 670 Critical Ranges as Given by Electrical Resistance....... 670 Critical Ranges as Determined Magnetically........ 671 Critical Ranges as Determined Calorimetrically....... 673 Critical Ranges from Heating and Cooling Curves....... 673 Summary of Previous Determinations of A3 and A2 in Pure Iron.... 675 The Present Investigation............ 678 The Experimental Method........... 678 Arrangement of the Apparatus.......... 679 The Measurements of Temperaturc.......... 679 The Measurement of Time........... 679 The Thermocouples............ 681 Temperature Scale and Calibration of Thermocouples...... 681 Mounting of Thermocouples........... 682 The Differential Measurements.......... 682 The Furnace and Accessories........... 682 The Vacuum Pump............ 683 The Energy Supply............683 The Rheostat.............. 683 The Materials Investigated............ 685 Sources of Iron............. 685 Preparation and Description of Samples......... 685 Chemical Analyses............. 687 The Experimental Data............. 688 The Preliminary Observations.......... 688 The Definite Series............691 Description of the Plotted Curves........... 694 The Effect of Plotting at Different Intervals........ 694 The Curves of the Definite Series.......... 695 . The Curves of the Preliminary Series......... The Existence of Other Critical Ranges......... 696 The Microscopical Examination........... 697 Summary and Conclusions............ 698 Bibliography............... 701 Plates................ 704

Jan 1, 1914

By E. A. Beck

For a number of years many attempts have been made to use thermit in order to do away with piping in ingots. Some of these attempts were successful, while others did not give the expected results. Nearly every plant had its own method of using the thermit, and no special care was taken to study the results or to find the causes for lack of success. Formerly the principle of the process was to decrease the piping by introducing a can filled with thermit, attached to an iron rod, into the head of the ingot directly after it had been poured. In this case the thermit reaction took place in the upper part of the ingot, and it was thought that through the heat produced the head would keep liquid longer and piping thus be reduced. In other words, the aim was to keep the head of the ingot open by making use of the heat of the thermit reaction, which would thereby give the gases in the steel sufficient time to escape. This result can be attained by the application of a large enough quantity of thermit, but it would not be economical in general practice, and could only he used for high-grade material. Many steel-makers abroad and in this country have had this experience. The Th. Goldschmidt A. G., Germany, has, therefore, made a special study of this question with the cooperation of a well-known steel company, and has worked out a new method for the application of thermit for this purpose. The results obtained have been most satisfactory and reliable, and this process is now used in Germany on a large scale in many prominent steel-works. The thermit is applied in cans, as in former years, but the principle of the process is entirely different. The object of using the thermit is not to heat the steel and keep it liquid,

Jan 1, 1914

By Ralph Nichols

The mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are the Pittsburg Idaho Co., Ltd.; the Latest Out Mining & Smelting Co., Ltd.; and the Oilmore Mining Co., Ltd. Besides the above propertiea, there are a number of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course and a dip to the west of from 40' to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine. Character of Ore. The ores of the district are oxidized, carrying an excess of iron over the silica (insoluble matter). The vein filling is a mixture of limonite and hematite, which is replaced by shoots of lead-silver ores. The lead minerals consist of carbonate of lead principally, but with small quantities of sulphide, sulphate, and other lead minerals.

Jan 1, 1914

By Bruno V. Nordberg

The high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapt- ing this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 1, 1914

By Albert Sauveur

Floris Osmond, Honorary Member of the American Institute of Mining Engineers, born in Paris, March 10, 1849, died at Saint-Leu near that city, June 18, 1912. Taken suddenly ill with congestion of the brain while on his way from Paris to his home, he reached it in time to write on the typewriter his last wishes, one of which was that no biographical notice of his life should be published. Holding Osmond's memory sacred, as those who have known him will, is it our duty to conform with his desire ? Shall no mention be made in our Transactions of the beautiful life and great achievements of one of our most honored members? Is it not, on the contrary, incumbent upon us to disregard Osmond's instruction in this matter and to place on record our admiration for the nobility of his life, for his talents and for the importance of his work, that younger men may be inspired by it with a desire to be guided by worthy motives in the path of unselfish pursuits ? I cannot feel that in following this course I am disloyal to Osmond's memory and I am strengthened in this belief by the opinion of men of high honor whom I have consulted before undertaking the writing of this obituary notice. One of them, Professor Henry M. Howe, justifies my decision better than I could do it myself when he writes : " Let us look frankly at the matter. Here we have a most extraordinary life, a life of rare beauty and power of inspiration to the rest of mankind. In my opinion we should not deprive mankind of the stimulating influence of the example of M. Osmond simply because he shrank from publicity. Our young men see every day how greed and vulgar push succeed, and with what material rewards they are crowned. They see too rarely the more valuable crown which comes to self devotion. A permanent and public recognition of the beautiful qualities of Osmond's life cannot fail to appeal to the imagination of young men and to help to deflect them toward leading a noble rather than a sordid life. Therefore I feel that the Revue de Métallurgie and other bodies owe it to the public to give prominence to his career by means of biographical notices."

Jan 1, 1914