Search Documents

By W. R. Hamilton

THE knowledge of the existence of petroleum in Southern California dates back to the days of the missions. The presence of asphaltum and semisolid bitumen was reported at Santa Barbara in 1792, but no serious attempt was made to develop oil until Professor Silliman's optimistic report in 1865 started California's first oil boom. Wells were drilled in many counties of the State, but the equipment was unsuitable and the drilling difficult and no production was obtained except in Ventura County. Even there the production was of little importance commercially, and not until the early '80s did it become sufficient to again attract attention. In 1888 the production for the State had reached a total of about 700,000 bbl. per year, practically all light oil produced in Ventura County, Pico Canyon, Los Angeles County and in the Puente Hills. The production of petroleum attained the dignity of an industry in 1895 when the Los Angeles City and Coalinga fields were discovered. The subsequent development has been remarkable, and in 20 years the production has increased from 1,000,000 to 100,000,000 bbl. per year. The refining industry has kept pace with the production of oil. The Pacific Coast Oil Co., the predecessor of the Standard Oil Co. of California, was the virtual pioneer refining company of the State, having built a refinery at Alameda about 1880. When purchased by the Standard, about 1902, it was dismantled and the refinery at Point Richmond was built. The Richmond refinery is now one of the largest in the world, having a capacity in excess of 60,000 bbl. per day. A small refinery was built by the Union Oil Co. at Santa Paula in the early days of the industry and later many asphalt refineries were in operation in Southern California. The Pacific Coast Oil Co. was then, as has been its successor, the Standard Oil Co. of California, the principal refiner and marketer of light products, the most valuable of which was kerosene.

Jan 6, 1916

By David Scott

WHEN mining operations were first instituted in the mines of the Miami Copper Co., at Miami, Ariz., the relatively hard character of the ground in the western section of the property made it seem advisable to use a wide shrinkage stope and pillar system. The system as finally evolved was applied to the mining of 2,300,000 tons of ore by the use of stopes and pillars each 50 ft. in width. Development, mining and extraction of this reserve has been continuously in progress since 1910, and the final stages of extraction are now reached. A complete survey of all phases of this system can therefore be made. Modification in working methods was obviously necessary, and the system to be described is believed to be typical of the best features. DEVELOPMENT The preliminary work had three main objectives: The opening of a haulage level, the construction of a drawing-off level, and the driving of sublevels for use in stoping. In addition to these, some extra sublevel drifting was necessary to determine exactly the boundaries of the orebody, the general outline having been determined by churn drilling. This development was based on the requirements of stopes 50 ft. wide, with pillars 50 ft. wide between each stope. The length of these units varied from 200 to 500 ft.

Jan 6, 1916

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

COLUMBIA SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON FRANK A. Ross The first meeting of the Columbia Section was held on March 24, as a part of the 1916 Northwest Mining Convention which was held under the -auspices of the Spokane Mining Men's Club assisted by the Spokane Chamber of Commerce, the technical program being in charge of the Spokane Engineering and Technical Association assisted by the local sections of the A. I. E. E., A. S. C. E., and A. I. M. E. The program of the successive sessions was carefully arranged with view to its application to mining, and in addition to the technical program there were exhibits of ores, minerals, devices, etc., of interest to the delegates, who numbered over 500. A portion of the program was also arranged with special reference to the requirements of the prospector and miner. A reception, a banquet, a complimentary luncheon, a regular daily call' of the Stock Exchange, a visit to the High Schools and to one of the substations of the Washington Water Power Company and to the Union Iron Works kept the visitors entertained, the ladies being looked after by a special committee of ladies who held open house during the entire week. Several important resolutions were passed by the Convention and one by the Columbia Section, A. 1. M. E. With Stanly A. Easton, chairman, presiding, the Columbia Section, American Institute of Mining Engineers, occupied the time between 2.00 and 5.30 p.m., March 24th, the Moorish room of the Spokane hotel being filled with members and their guests. "The Apex Law and the Mineral Surveyor" was a paper presented by F. W. Callaway and generally dis-cussed because of its local application in the Coeur d'Alenes, the conclusions being reached after expensive litigation between two of the large mining operators in that district.

Jan 6, 1916

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from Sept. 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so, that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining, reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will, use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 6, 1916

By Frank Fahrenwald

INTRODUCTORY A COMPLETE list of the elements as given for 1915 includes 18 that melt above 1,700° C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure .metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures* and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,1 of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation.

Jan 6, 1916

By P. B. Liebermann

THE resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade.

Jan 6, 1916

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10, 1916 to May 10, 1916. ALLEN, WILLIAM R.... Pres., Boston and Montana Development Co., Butte, Mont. BARKER, EDGAR EARL, Min. Engr. Mine Supt., Chile Exploration Co., Chuquicamata, Chile, S. Amer. BAYLESS, JOHN Z., Met. Engr Alaska Gastineau Min. Co., Thane, Alaska. BLACKWOOD, ARTHUR E., Mgr., Sullivan Machinery Co., 30 Church St., New York, N. Y. BREYER, FRANK G., Chief Testing Dept., The New Jersey Zinc Co., (of Pa.), Palmerton Pa. CARPENTER, JAY A., Mill Supt... . West End Cons. Mining Co., Tonopah, Nev. CORLESS, GEORGE BRADFORD, Geol., Missouri Bureau of Geology and Mines, Joplin, Mo.

Jan 6, 1916

By Leon Dominian

I. INTRODUCTION APART from local needs in the country's development, the interest attached to Turkish fuels grows chiefly out of the importance of the railway industry in Asiatic Turkey. Geographical conditions make of the tracks in this region the most essential link in a chain of world-girdling lines. By its position Asia Minor can be likened to a bridge in the through routes destined to connect European factories with Asiatic and African markets. An uninterrupted right-of-way from points in central Europe to populous Indian cities must necessarily pass through the valleys A Anatolia. Crossing thence the Taurus Mountains its natural passage is indicated as the Mesopotamian lowland and the shores of the Indian Ocean. Similarly land connection between Europe and Africa can be obtained only by passage through Asia Minor, Syria and Palestine. The occurrence of fuel within an area of such significance from the

Jan 6, 1916

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, graduate engineer, aged 44, with over 22 years' experience in connection with the development of large coal and coke properties in different parts of the country, desires position as general manager or general superintendent of large bituminous coal producer, or will take an interest and the management of a smaller operation. No. 258 Member, aged 41, mining engineer, manager or general superintendent, 20 years' experience, 10 years in Mexico, 5 years Western States, 5 years abroad. Guarantee results, fluent Spanish, excellent references. New York interview. No. 282. Member, technical mining graduate, 10 years' experience, especially in design, erection, construction and purchase of power and mining equipment and supplies, desires position in purchasing department. Married, aged 32, employed at present, references furnished. No. 295.

Jan 6, 1916

The suggestions of the members of the Institute are very much desired by the Committee on Nominations prior to deciding upon its nominations to fill the places of those officers who retire early in 1917. The Committee must make its final report to the Board of Directors early in October. The members are, therefore, asked to send in promptly their suggestions for Directors as well as for Vice-Presidents and President. The Committee hopes to hear from a large number of the members. The officers to be elected at the annual meeting in February, 1917, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: "The geographical districts to be considered by the Committee on Nominations shall be as follows, until otherwise ordered by the Board. District No. 1. New England, New York, and New Jersey, excepting New York City and district, which is provided for in the Constitution. (N. B.-New York City and district is designated District 0.) District No. 2: Pennsylvania.

Jan 6, 1916

The Students' Organization of the Michigan College of Mines was recognized as an Affiliated Student Society by the Board of Directors of the Institute, at a meeting held on April 28, 1916. At the College of Mines, University of Washington, 30 students and instructors took part in the annual spring excursion early in April. Studies were made of the new reverberatory and casting furnaces at the Tacoma smelter, the Du Pont powder works located on Puget Sound and the Britannia Mining and Smelting Company's mine and mills on Howe Sound, near Vancouver, B.C. The Britannia mills are using Hancock jigs, Burchart tables and Minerals Separation flotation cells to effect a high recovery on low-grade chalcopyrite ore. The Mining Club, University of. Wisconsin, elected the following officers for the second semester of the present school year: J. G. SKIRM, President, H. L. RAU, Vice President, T. C. SHERWOOD, JR., Secretary-Treasurer, H. E. HODGSON, Mucker, , F. M. WOLVERTON, Assistant Mucker. Theo. C. SHERWOOD, Jr., Secretary.

Jan 6, 1916

By Robert P. Burrows

Discussion of the paper of R. P. Burrows, presented `at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2237 to 2245. EDWIN M. CHANCE, Wilkes-Barre, Pa.-I have been very much interested in the comprehensive and able discussion of the important topic of mine lighting just given by Mr. Burrows, especially as I know by common report Mr. Burrows' ability and his close touch with the development of the electric mine lamp, and its use in mines in connection with a portable electric lamp. It is regrettable that Mr: Burrows was not able to acquaint himself more closely with the cost of mine illumination, the actual cost, as produced by a portable light as carried by miners, whether a flame safety lamp or an open light. Had he been able to acquaint himself more closely with these data, he perhaps would not have arrived at some of the conclusions which he has presented to us in his paper. For example, we find Mr. Burrows advises that the open torch is by far the cheapest source of illumination, as produced by a portable light. I am very sure that is not the fact. The cost of miners' oil varies from about 25.c. a gallon to 90b. a gallon. The various States have passed laws from time to time rendering it mandatory that the miner shall use, whether he is willing or not, a so-called better or higher grade of burning oil. These laws have entailed the use of an oil so expensive that the use of the oil torch has become practically impossible, and the acetylene or carbide miners' lamp has largely taken its place. I have evolved a few figures showing the relative efficiency and usefulness of the open oil torch and the acetylene miners' lamp. For example, the acetylene miners' lamp consumes or burns 4 liters of acetylene per hour, or 0.14 cu. ft.; the oxygen consumed is 10 liters, or 0.35 cu. ft. per hour; air consumed, 50 liters, or 1.76 cu. ft. per hour; black-damp produced, 40 liters, or 1.41 cu. ft. per hour; air rendered extinctive to the acetylene flame, 112 liters, or 3.95 cu. ft. per hour; carbide con- sumed, 13 g. per hour. The open oil torch, on the other hand, burns about 20 g. of oil per hour; the oxygen consumed is 48 liters, or 1.69 cu. ft. per. hour; air consumed, 240 liters, or 8.47 cu. ft. per hour; blackdamp produced, 191 liters, or 6.73 cu. ft. per hour; air rendered extinctive to oil flame is 1,413 liters, or 49.92 cu. ft. per hour.

Jan 5, 1916

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 10, 1916 to Apr. 10, 1916. ALLEN, P. R., Pres., McAlester Coal & Coke Co., Knight Templar Bldg., McAlester, Okla. BERNARD, CLINTON PERCIVAL, Min. Engr., Care Forminiere Mission Kasai, Tschikapa, Congo Belge, W. Africa. CARPENTER, GEORGE 0., Vice-Pres National Lead Co. St. Louis Mo. CLARK, WILLIAM ANDREWS, JR., Min. Engr., Pres., Elm Orlu Mining Co., Butte, Mont. CLAYTON, CHARLES YANCEY, Asst. PrOf. of Metallurgy and Ore Dressing, Missouri School of Mines, Rolla, Mo. COHEN, JULIUS MILTON, Mgr. Croesus Gold Mines, Ltd., Matheson, Ont., Canada. CRAMER, WILLIAM BRONSON, Met. at Concentrator, Old Dominion Copper Min. & Smelt. Co., Globe, Ariz. DAHL, SIMEON H., Mill Supt., Messina Transvaal Dev. Co., Messina, Transvaal S. Africa.

Jan 5, 1916

By H. Hanemann

Discussion of the paper of H. HANEMANN and PAUL D. MERICA, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2371 to 2385. JOHN A. MATHEWS, Syracuse, N. Y.-I should like to ask the authors if there is any evidence of chemical change resulting information of, alpha iron from the gamma crystals found in nickel steel of high nickel content when stressed beyond the elastic limit, similar to the effect produced by drastic cooling. Would the stresses mentioned and the drastic cooling both result in an increase in magnetic induction? I would also like to ask the authors if they have made a test of the hardness. It would be very interesting to see whether the hardness decreased under the conditions of stress, as might be the case if alpha iron were produced. PAUL D. MERICA, Washington, D. C.-While it is impossible to state absolutely, it is my belief that the effect of deformation is approximately the same as, that of -drastic cooling, but we did not make a test, of the hardness.

Jan 5, 1916

By Grafton M. Thrasher

Discussion of the paper of GRAFTON M. THRASHER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 106, October, 1915, pp. 2129 to 2138. RICHARD MOLDENKE, Watchung, N. J.-Mr. Thrasher is to be commended for developing a very interesting comparison between high- and low-carbon and silicon malleable cast irons for an equal degree of chill. His deductions are unquestionably correct, though the application to daily practice is open to serious criticism, from the standpoint of the man who receives the castings, as will be shown later on. Running over some of the points which affect the tests in question: Mr. Thrasher admits that the temperature of pouring has a serious influence on the degree of chill shown in the test plugs he made. This is a well-known fact, and I would like to add that another serious trouble comes from oxidized iron when the heats have been unduly prolonged. Such metal always shows more chilling action for a given silicon and carbon content than normally melted iron. Indeed, the test piece quoted giving the extreme of the chill line (1.07 per cent. Si and 2.47 per cent. total carbon) was such a poor heat, a ferro-silicon addition never "doctoring" up the metal sufficiently to show normal good strength. In spite of these irregularities, which would simply change the curve slightly, I take it that Mr. Thrasher's results can be accepted as reliable enough to establish the relationship of silicon and total carbon as shown. When, however, the claim is made that silicon and carbon can be substituted for each other in mixture-making (a claim which may be perfectly correct metallurgically), a very important factor is forgotten, causing the purchaser of the castings much annoyance. This is the contraction (erroneously called shrinkage) of the castings. They will no longer be true to pattern. The lower the total carbon is allowed to drop, the greater the contraction, and increasing the silicon correspondingly will not correct this trouble. No wonder that recently, in revising the Standard Specifications for Malleable Castings it was necessary to increase the variation of castings from requirements considerably over what was formerly found sufficient. The habit of running up the proportion of silicon and escaping danger from grayness of the metal by copious steel additions was evidently too tempting to manufacturers, as their molding losses were thus kept down and a very soft malleable iron resulted. The customer, however, got serious variations in his work, which was not the case when the total carbon was kept between 3.25 and 2.75, and the silicon held as low as possible without undue cracking of the hard castings.

Jan 5, 1916

Experiments on the Rate of Heat Transfer from a Hot Gas' to a Cooler Metallic Surface Members of the American Institute of Mining Engineers will be much interested in the subject of teat transfer from a hot gas to a cooler metallic surface, and although the book on this subject recently published by the Babcock & Wilcox Co., of New York, deals primarily with boilers, it contains a great deal of information which metallurgical engineers will find of great value. The book starts out with an introduction giving some of the current theories regarding this subject; it then describes in detail the experimental apparatus used, and the methods of conducting the experiment's and recording the data. Then follow some account of the determination of radiation losses in jackets and cooler; measurement of metal temperatures; detection and correction of errors; etc., concluding with a discussion of the results and derivation of corrective formula for heat absorption; heat pressure rate and specific heat of gas.

Jan 5, 1916

By W. Mostowitsh

I. Introductory LEAD sulphate occurs as anglesite, and is formed in every roasting of lead sulphides or sulpho-salts containing lead. In smelting in the blast furnace an ore containing natural or artificial lead sulphate, a large part of the sulphur present goes to the formation of the intermediary product matte which requires further treatment for the recovery of the values it contains. It is therefore of importance to study the behavior of lead sulphate at elevated temperatures, both without and with reducing agents, especially as the information available gives data which are more or less conflicting. II. Decomposition of Lead Sulphate by Heat The dissociation of PbSO4 into PbO and S03 or S02 and 0 has been discussed by many metallurgists. The following data are considered to be representative. Doeltz and Graumann1 found that PbSO4 was not affected by heat at 800° C.; that dissociation began at 900° C., and was rapid at 1,000° when the salt lost in 1 ½ hr. 14.3 per cent. of its weight, the dry salt containing 26.43 per cent. SO3. Hofman and Wanjukow2 summarize their work upon the dissociation of metallic sulphates with the statement that the decomposition of PbSO4 begins at 195° C., but progresses very slowly, with the formation of the basic salt 6PbO.5S03 at 705°; that this salt undergoes a transformation at 847°, begins to be decomposed at 888°, to sinter at 896°, and to fuse at 910°; rapid dissociation begins at 952°, and is accompanied by volatilization of PbO; retardations at 958° and 962° indicate an acceleration of decomposition which, however, is not complete. Proske3 found that PbSO4 gave off at 900° C. in 30 min. only 0.63 per cent. of its SO3, and that the loss increased with

Jan 5, 1916

By Enrique Hauser

Discussion of the paper of ENRIQUE HAUSER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 521 to 534. GEORGE A. BURRELL, Pittsburgh, Pa. Mr. Hauser determined the influence of inert gases on the properties of fire-damp mixtures, and one might take some issue with his work on the effect of hydrogen, on those mixtures. It is valuable information to have, but as far as the practical application of it goes, it is not of much significance, because one does not find it in mines, at least not in any appreciable amount. The same Fig. 1.-APPARATUS FUR DETECTING COMBUSTIBLE GASES IN AIR. thing can be said of ethylene. Ethylene is formed in considerable quantities as a product of heat reaction, but normally, in the coal mines, as a result of a great many analyses we have made at the Bureau of Mines, we cannot say that ethylene is a combustible gas found in the fire-damp in coal mines.

Jan 5, 1916