Search Documents

By D. J. McAdam, R. W. Mebs

The technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. According to the prevalent view,8 the technical cohesive strength of a metal. in any particular state as regards prior mecharlical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress. In two previous papers by one of the authors, evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion Limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.' In this paper, as in the previous papers,14.15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated 33, and the intermediate principal stress will be designated S². The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress."l4, .l5 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,15 however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average Of the three principal stresses.* This in fluence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers,".'5 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant • Any stress system ma? be resolved into a polarsymmetric stress causing pure volume strain and a combination of pure shearing stresses. which cause no change of volum

Jan 1, 1945

By D. H. Platt

Bauxite, the principal source of aluminum, has been mined from deposits in Saline and Pulaski Counties, Ark., since 1899; war needs have greatly stimulated production. Many of the ore deposits are basin-shaped and either outcrop or are covered by a shallow-depth overburden at their peripheries; these are mined by stripping and open-pit methods. When stripping becomes economically impracticable, incline shafts or slopes are sunk on the dips of the deposits, and underground mining is done on the retreat, using a room-and-pillar method.

Jan 1, 1945

By David B. Reger

Widespread wildcatting for new supplies of natural gas and the beginning of importation from the southwest characterized the petroleum industry of West Virginia during 1944. Within the state, drilling for oil did not increase but. more gas wells were completed than in any previous year since 1937. Out of 40 wildcats drilled there were 25 gas discoveries and 15 dry holes. No commercial oil was found in the 40 wells. The proved limits of several oil pools were slightly extended by marginal drilling, resulting in 1300 acres of new oil territory, although no distinctly new pools were found. At least four new gas pools were assuredly discovered and various successful wildcats indicate future pools or wide extensions. The new proved gas territory, in definite new pools and definite extensions, is about 34,000 acres. A considerable net decline of proved oil has occarred and probably a slight decline of proved gas reserves. The account of operations, as gathered from trade journals and other reporting services, shows that 918 new wells were drilled, resulting in 71 oil wells with 613 bbl. of daily new production; 577 gas wells with 305,372,000 cu. ft. of daily open flow, and 142 dry holes. Also, 107 old wells were drilled to deeper sands, with 22 bbl. and 12,327,000 cu. ft. of added production. On the new wells the oil average was 8.6 bbl. per well per day, and the gas average was 529,241 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 15.47 per cent. On deeper drilling the ratio of failures was 19.63 per cent. Production of oil for the year was estimated by the Oil Weekly as 3,069,000 bbl., as compared with 3,349,000 bbl. in 1943. Production of natural gas for the year is estimated by the author as 200,000, 000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 223,789,000,000 cu. ft.t in 1943.

Jan 1, 1945

By Robert B. Fisher

[The purpose of this paper is to acquaint manufacturers of various types of asbestos product's, particularly those that specialize in materials used for sound deadening, vibration damping, and filtration, with a recently invested depth deposit of paligorskite, a type of asbestos usually called mountain leather. In the past this mineral has been only a museum curiosity but it possesses characteristics that may adapt it to industrial uses. The deposit is on Lemesurier Island, near this entrance to Glacier Bay, in the northern portion of southeastern Alaska, at approximately latitude 58° 17? N., longitude 1360 05' W. The island is about 4 ½ miles in east- west length and miles in width. The property on which the deposit occurs is owned by the locator Joe Ibach, end it was brought; to the attention of the Bureau of Mines by Col. George B. Norris. A Bureau of Mines engineer, accompanied by the owner and Chris Ellingen, visited the property sand examined the open-cuts from May 7 to 10 in 1944. The purpose of the examination was to determine the approximate extent of the occurrence and to obtain samples of the material for identification end study of its utilization.]

Jan 1, 1945

By Claude W. Sill

In the course of a series of investigations on vanadium deposits of the western United States, the Bureau of Mines collected many hundreds of samples for chemical analysis. As uranium is often associated with these vanadium minerals, they were also analyzed for uranium, which was pound to be absent in a large percentage of the samples. Since the usual methods for determining uranium are laborious and time-consuming it is very desirable to have some simple qualitative test that can be applied prior to a quantitative analysis to determine whether uranium is present or absent and thus save the time and expense of applying the quantitative analysis to the large proportion of samples containing no uranium. To be acceptable, the test should be specific for cranium, sensitive enough to detect small amounts of uranium, and. simple enough to make it worthwhile to apply. The available methods for detecting uranium lacked one or more of the desired characteristics. Eventually, however, a method was worked out that satisfied all the requirements. This method is probably more specific and sensitive than the usual qualitative methods for uranium, and its simplicity and speed of application make it ideal for testing samples prior to quantitative analysis.

Jan 1, 1945

By Sara J. Davenport

Hydrogen sulfite has been listed (1)3/ as a possible hazard in 50 occupations, many of which are in the mineral industries. The effects of its occurrence in the petroleum industry made themselves felt more than two decades ago, resulting in a comprehensive study (2) of the toxic gases from Mexican and other high-sulfur petroleum products. The mining industry, likewise, has had cause to guard against this gas. Enough hydrogen sulfide has been found in coal and some noncoal mines during normal operations to cause severe eye irritation, some serious illness, end even fatalities. It is usually a product of the decomposition of sulfur compounds and may be produced by burning explosives containing sulfur; the gas in harmful qauntities is formed by the use of block blasting powder or by the use of dynamite in blasting sulfide ores. Hydrogen sulfide is readily soluble in water, and enough may be released from water streams in coal and noncoal mining to cause fatal poisoning it is found sometimes in stagnant water underground, particularly where ventilation currents are absent, and great care must be exercised when accumulations of such waters are disturbed, as exposure to comparatively low concentrations of the gas evolved therefrom has caused fatal accidents.

Jan 1, 1945

By George H. Found

DURING recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" of a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating mechanisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experimental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,1 damping due to localized inelastic stress relaxation at inhomogeneities within the metal,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.4 How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables have been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About 100 hr, after straining, a stable value is reached of magnitude proportional to the amount of strain.7 In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By R. B. Mears, G. F. Sagar, R. H. Brown

There are well recognized procedures for determining the various tensile, fatigue, and other mechanical properties of the common structural materials. This makes it possible for engineers to design structures of various materials which have adequate initial strength to stand the stresses to which they are subjected in service. There is also considerable general information about protective measures suitable for protecting the usual structural materials from the effects of ordinary environments. However, often insufficient quantitative information is available on the combined effects of stress and corrosion to permit the designer satisfactorily to appraise the structure from the stress-corrosion standpoint. This situation is further complicated by the fact that the stresses causing stress¬corrosion failures are usually not the design stresses but rather the residual forming and assembly stresses which are generally of unknown magnitudes. Thus, tests which will rapidly evaluate the susceptibility of materials to stress-cor¬rosion failures are extremely useful. Of particular value are tests which can be applied to built-up structures as well as to simple specimens, since, as mentioned above, residual stresses often are caused by fabricating procedures and assembly operations. The present paper contains

Jan 1, 1945

By R. F. Evans, J. M. Avery

MUCH has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of -magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore 'of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this operation is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft. apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. PRODUCTION OF MAGNESIA FROM DOLOMITE In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime (CaO) value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or

Jan 1, 1945

By Henry F. Hebley

THE solid fuel industry, especially that branch represented by bituminous coal, is gradually becoming aware of its ? paramount importance in a world where there is an ever increasing demand for the products of a mechanical age. In practically every process of manufacture, the necessity for energy in some form is being multiplied. Some of that prime energy is derived from water power-hydro-electric schemes, flood control schemes, etc. - but often the electrical energy thus developed is generated at great distances from the load centres, requiring long transmission lines with consequent transformer and transmission losses. A few plants have harnessed the tidal power of the seas and one has harnessed the energy of the wind in a modern manner. All of these schemes are dependent on certain natural geographical, hydrographical, and physical advantages of terrain, as well as an adequate area of consumption of the energy developed. If flood control is the primary object, then power generation is a by-product; and the economics of large capital expenditure on power generating equipment must be considered in that light.

Jan 1, 1945

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.HARMLESSNESS OF ALUMINIUMAnimal experiments having served their purpose, it became necessary to consider means to test the discovery on humans. A question for immediate consideration was: Is aluminium harmful to man when inhaled as a fine powder? While the animal experiments were reassuring, since they conclusively showed the powder to be innocuous when breathed by animals, it was, nevertheless, desirable to have additional reassurance with regard to its effect upon human beings.Through the courtesy of the Aluminium Company of America and especially the valued interest in this problem displayed by that Company's Director of Research, Dr. Francis C. Frary, a study was made of the records pertaining to the health of a group of 125 employees who had for many years been engaged in the manufacture of finely powdered, metallic aluminium for the paint and ink industries. The conditions were such that these employees had inhaled varying and oft-times very dense concentrations of this powder daily over periods ranging from 6 to 23 years, the average 101 the group being 12 years. X-ray pictures of their chests showed no abnormalities attributable to aluminium. Their general health seemed better than that of the 3,000 workers in other sections of the plant. In fact, the early films of three employees in this group of 125 showed shadows suggestive of minimal tuberculosis, which shadows were not discernible in films taken after considerable periods of exposure to aluminium powder.The harmlessness of aluminium was; by this study, reasonably well established at the outset, a finding subsequently verified by Ontario research on humans.PROPOSAL TO TREAT HUMAN SILICOSISBased upon these findings, a proposal to treat silicotics with aluminium was discussed by officials of the Mclntyre Mine and the Banting Institute.

Jan 1, 1945

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Helmut Thielsch

DURING the last three decades a great many arguments have been presented on the subject of "mosaic" or "block" structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner structure of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as plasticity, ferromagnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals, the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because of the vast extent of the field of submicroscopic structures, it shall be the purpose of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic pattern f and effects of cold reduction and recrystallization will be shown in further studies later on. IMPERFECTIONS IN CRYSTALS The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. Ideal, or Perfect Crystals.-Crystals without any structural imperfections are called "ideal crystals," or "perfect crystals," meaning a homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.-" Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities existing in these groups mean that the orientation of the crystallographic axes will not be the same at every point within the interior of a crystal (or grain of a polycrystalline body). Perfect Real Crystals.-The term "perfect real crystals" is generally used to describe crystals with minute structural or thermodynamical inhomogeneities. The former

Jan 1, 1945

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

By Peter Grandone

Steel and iron pipe lined with cement to protect it against corrosion has been used in the municipal water systems of the New England States since about 1870. In most recent years, the petroleum industry adopted cement-lined pipe to forestall corrosion, particularly in those areas where large quantities of corrosive brines and hydrogen sulfide are associated with the oil produced. Many of the oil companies had on hand large quantities of corroded pipe, normally disposed of as scrap, which could be cleaned, lined with cement, and returned to service. It was soon learned that after the so-called scrap pipe was lined with cement much of it could serve fully as well as new cement-lined pipe. The demand for lining used pipe with cement resulted in the establishment of several processing, plants in the Mid-Continent oil-producing area. Today six cement-lining plants serve the areas three in Oklahoma and one each in Kansas, Texas, and Illinois. All of these plants have lined large quantities of used pipe for the brine-disposal systems of western Kansas, Illinois, and east Texas and also for the operators of water-flooding projects in northeastern Oklahoma and southeastern Kansas, where large quantities of brine and fresh water are being injected into the oil-bearing formations as a secondary oil-recovery method. Since war demands during the past 2 years have created an acute shortage of steel, the need of reclaiming used pipe for the expansion of oil-producing operations has become more evident than ever before. Thus the new industry (about 6 years old) - lining used pipe with cement - is saving large quantities of steel at a critical time by reclaiming used pipe and preventing further- corrosion.

Jan 1, 1945

By Herbert H. Kellogg

IN 1930, Taggart, Taylor and Knoll1found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the "classical "[t] theory of Brownian movement and proposed an "ionization" theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,"5 Wark's "Principles of Flotation,"6 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.7 Bankoff15 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, all particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid-the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that the addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1945

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By W. H. Brandt

THERE has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidence. Particularly noteworthy among the empirical work is that of Grossmann,12 who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.1-5 They have shown that formation of pearlite proceeds by a process of nucleation and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to fill in a small part of the gap. A method was presented recently14 for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eutectoid steel was calculated, using linear extrapolations of the ferrite and cementite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and V, the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1945