Search Documents

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By Robert H. Leach, C. H. Chatfield

This paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in conlmercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordaq4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. Analysis of Steeling Silver Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same ana,lysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry I1 in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

By J. F. Wilson

Steady-state flow theory, previously applied to displacements with two mobile phases, is extended to cover down-structure flow involving three mobile phases: oil, gas and water. When used with normal reservoir fluid properties, the theory predicts the existence of four distinct flow regimes and the conditions under which each regime exists. The predicted behavior is verified by a parallel-plate model study. INTRODUCTION Special problems exist when a water flood is contemplated in a dipping reservoir having a substantial gas cap. Normally, the gas-cap region is one of very low oil saturation. If oil is moved into the gas cap during the flood, a loss in recovery results. Efficient recovery of the oil underlying the gas is therefore difficult. In two reported field water floods, injection into the gas cap has been used to solve these problems. At the West Norfolk Garr Sand Unit, injection into the upstructure region of the reservoir was made for the stated purpose of filling up the gas cap with water.' The purpose in the Sholem Alechem Fault Block "A" Sims Sand Unit was to form a continuous water barrier between the gas cap and oil band.' A laboratory model study preceded this flood and was described in the same publication. Both of these gas-cap water injections gave satisfactory results, but the published data are insufficient to allow generalizing to other field conditions. The present investigation was also undertaken to obtain results for a specific field problem. However, these results will be shown to be in agreement with an extension of the Dietz3-5 mathematical model to three-phase flowing systems. The agreement between the theory and the model studies indicates that the mathematical model can be used to describe completely the flowing system under some conditions, and to indicate the general type of flow to be expected under all conditions. FLOW THEORY The Dietz equations for two-phase flow are derived "' for the case of constant-velocity linear flow in a homog- eneous porous medium. The transition zone between the fluids is assumed to be of negligible extent so that the displaced and displacing fluids are separated by a sharply defined interface, as illustrated in Fig. 1. The density and mobility of the displacing fluid are constant over the region behind the interface, and the same properties of the displaced fluid are constant over the region ahead of the interface. To extend the Dietz equations to three-phase systems, we postulate the flowing system shown in Fig. 2 and determine the conditions under which it can exist. The

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By Richard P. Rothwell

Though coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence and foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869—70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, " though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

By Ronald S. Conti

Historically, underground mine rescue teams have received training only in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fire drills every 90 days, this does not fully prepare them for the conditions that may be encountered in real escape situations, such as smoke filled entries. This paper describes technology and realistic training simulations that have been identified for the general workforce and mine emergency responders. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. These technological advancements can improve the state of readiness for rescue personnel and increase the chances of survival for personnel escaping from underground emergencies.

By D. D. Dunlop, J. R. Welker

The growing interest in the use of CO, in crude oil recovery increases the need for data on the effect of CO, on hydrocarbon physical properties. Data are presented on the solubility of CO, in various dead oils, the swelling changes in CO2-oil solutions and the effect of CO, on dead oil viscosity. This latter property shows the most pronounced effect, with viscosity reductions up to 98 per cent of the uncarbonated viscosities. An empirical method of estimating the viscosity of carbonated oils is presented. The apparatus and procedures used are described in sufficient detail to allow others to make similar studies. INTRODUCTION The effect of dissolved carbon dioxide on the swelling and viscosity reduction of specific hydrocarbon oils has been observed and recorded by a number of investigators.'- me object of this paper is to offer a means of predicting these effects for crude oils free from natural gas, using the dead state viscosity and gravity of the crude oils. The CO, solubility and swelling of numerous crude oils were determined in a visual cell at various pressure levels. The viscosity of the oils carbonated to various pressure levels was then determined by measuring the pressure drop across a capillary tube. From these data, the physical properties were correlated empirically. The resulting correlations allow the prediction of CO, solubility, swelling and viscosity reduction if the dead state gravity and viscosity of the oils are known. SOLUBILITY AND SWELLING MEASUREMENT EQUIPMENT AND PROCEDURE A high pressure visual cell was installed in a constant temperature cabinet. A test gauge was attached at the top of the cell for pressure measurement, and a line was run through the cabinet wall to a wet test meter which was used for volumetric measurement of the gas. The first step in making a test run was to put the oil in the cell up to a level about half to two-thirds of the total volume. This required about 50 to 65 ml of oil. carbon dioxide was then bubbled up through the oil for a time during which the pressure of CO2 in the cell was kept above 800 psia. Saturation of the oil with CO2 at this pressure and ambient temperature was confirmed by slowly bleeding CO2 through a valve to the atmosphere. If the oil was completely saturated with CO2, bubbles of gas would form in the oil at the first small decrease in pressure. If the oil was under-saturated, no bubbles formed until the pressure was decreased to the saturation pressure existing in the oil. If this saturation pressure was lower than that desired, more CO2 was bubbled through the oil until the desired level was reached. After saturation at ambient temperature was completed, the cabinet temperature was adjusted to the desired level and the cell was allowed to reach temperature equilibrium. After temperature equilibrium was reached, the pressure was again decreased slightly, and the oil again checked for full CO2 saturation at the cell pressure. The pressure now had changed because of the difference in solubility of the CO, in the oil at higher temperatures and the expansion of CO2 as the temperature increased. The outlet tube from the cell was then connected to the wet test meter and the CO2 was allowed to flow slowly out of the cell and through the wet test meter at ambient temperature and pressure. The water in the wet test meter had previously been saturated with CO2 at ambient temperature and pressure by allowing CO2 to flow continuously through it lor a period of several hours. The gas flow was stopped at several pressures during the run and the cell was allowed to come to equilibrium; this made possible the measurement of solubility and swelling data at the intermediate pressures. The volume of the oil in the cell was recorded at each of the equilibrium pressures in order to obtain swelling data. DATA AND RESULTS The solubility of CO2 in the oil was calculated by the relationship V — V, where R. = solubility of CO, in crude oil, cubic feet of CO, measured at 60F and 1.0 atm/ bbl of dead state oil at the temperature under which solubility was measured, V, = volume of gas released from the cell between the saturation pressure and zero pressure, corrected to 60F and 1.0 atm, cu ft, V, = volume of CO: contained in the gas space above the oil, corrected to 60F and 1.0 atm, cu ft, and V, = volume of the dead oil in the cell in bbl at the temperature of the run. The volumetric data of Sage and Lacey' were used to calculate V., from the volume of CO2 at high pressures. The swelling factor was calculated as where V, is the volume of the C0,-

By W. William Culver

James Douglas became known in the nineteenth century for two reasons fundamental to his mining career: (1) his experimental work with copper hydrometallurgy, and (2) his grasp of the idea that the quantity of copper ore matters more than the quality. On the first reason, there is a moment for any technology that’s critically important—when it moves from an area of scientific interest to one that companies are founded on. This paper examines the original 1869 Hunt and Douglas Copper Process in the context of science and engineering as they were in the 1860 and 1870s. It was a “humid” process, developed at Quebec’s Harvey Hill Mine. Chemically, the Hunt and Douglas vat leaching process succeeded, but not the original companies using it. On Douglas’ understanding of ore quality versus quantity, luck had it that the first company to field test the Hunt and Douglas Copper Process was in Chile. The Hunt and Douglas patent made that transition from experimental model to operational plant in 1870 when the Compañia de Minas de la Invernada was organized in Valparaíso. As a joint-stock company, Invernada spread the risk of investing in the revolutionary, but untested, Hunt and Douglas Process. The company brought Douglas to Chile as a consultant in 1871. His experience with hydrometallurgy, combined with what he learned about the copper business while in Chile, set him off on a career in metal mining that both surprised Douglas and made him wealthy.

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By John Demol

Monazite, a rare earth and thorium phosphate mineral, is one of the major minerals processed for extraction of rare earths. Industry practice for treating monazite concentrates is to use either a sulfuric acid bake or caustic conversion route. In the sulfuric acid bake, monazite concentrate is mixed with concentrated sulfuric acid and roasted. The rare earth phosphate mineral is converted to rare earth sulfate which dissolves in a subsequent water leach. As the bake temperature increases above 300 °C, thorium becomes less soluble. Although acid baking is practised in industry, the bake reactions are not well understood. A combination of chemical analysis, XRD and SEM-EDS was used to identify reaction processes occurring during sulfuric acid baking of a 93 wt% monazite concentrate between 200 °C and 800 °C. The effects of these reactions on the leachability of the rare earths, thorium and phosphate were also examined.

By T. Sterry Hunt

In my address on the " Geognostical Relations of the Metals," delivered before the Institute on the 20th of February last (Vol. I Transactions, p. 331), I spoke of the rocks in the vicinity of Thunder Bay, Lake Superior, where I indicated two series of uncrystalline rocks resting upon the Huronian schists, the lower one consisting of dark-colored argillites and sandstones overlaid, apparently in slight discordance, by nearly horizontal red and white sandstone and marls, which were compared with those of Sault Ste. Marie, and those of the Portage Lake district, on the south shore. These latter sandstones, according to Brooks and Pumpelly, overlie uncomformably the Keweenaw series of copper-bearing amygdaloids, sandstones, and conglomerates, and are in turn overlaid by the Trenton limestone. I then proposed to call this lower series of Thunder Bay, that is to say, the dark-colored argillites and sandstones which are traversed by the silver-bearing lodes of that region, the Animikie group. Shortly after the publication of that address I received an abstract of a paper on the geology of that region by Professor Robert Bell, read before the Montreal Natural History Society, February 24th. He there confirms the statement made in my address that the gold of Lake Shebandowan occurs in the Huronian, which is also seen to be cut by the silver-bearing lodes just mentioned. Professor Bell, in this paper, proposes to designate both what I have called the Animikie group, and the overlying red and white sandstones, by the name of the Nepigon group, for the reason that the upper series is best displayed about Lake Nepigon. This latter series is by Logan supposed to be overlaid by the copper-bearing amygdaloids with conglomerates and sandstones of the north shore (apparently identical with those of Keweenaw); and the whole together, inclnding the Animikie group, constitute his Upper Copper-bearing group. These copper-bearing strata are by him supposed to be overlaid by the red and white sandstones of St. Mary, which are apparently the same with those sandstones which, according to Brooks and Pumpelly, overlie unconformably the similar cupriferous rocks of Portage Lake, and are, in their turn, overlaid by the Trenton limestone. Thus the sandstones which at Thunder Cape overlie the Animikie group are by Logan placed in the midst of the Upper Copper-bear-

By Stanko Nikolic

One of the keys to success in process development is incremental scale-up, allowing for potential problems to be identified and rectified. The ISASMELT™top submerged lance (TSL) process was developed to maturity using this method by Mount Isa Mines, now owned by Glencore. Commercialization only occurred once the process had been proven on each scale and as a result the ISASMELT™ technology now operates successfully around the world. An important parameter in the evolution of the technology has been the furnace campaign life. The initial commercial scale furnaces had minimal water-cooling. Although this led to shorter campaign lives, an extended development program resulted in the achievement of four-year campaign lives, without any water cooling. In tandem to the refractory designs Glencore Technology, supplier of the TSL technology, has progressed cooled copper lining designs for application to both the ISASMELT™ and ISACONVERT™ furnaces allowing for ultimate flexibility in the lining choice. This allows each ISASMELT™ operating site to minimize their overall life-cycle costs by balancing their campaign life with lining costs, energy inputs, and other shutdown requirements.

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy's law and material balance relations can be written as follows.

By R. J. Blackwell, A. L. Pozzi

Scaled laboratory-model studies provide a powerful method for evaluation of a proposed oil-recovery process. In recent years, models have been used extensively to evaluate processes in which solvents displace oil, both for general cases and for specific reservoir conditions. Since the performance of a miscible flood in a horizontal reservoir can be significantly affected by transverse mixing between solvent and oil, this displacement mechanism must be accurately simulated in the scaled model studies. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long times for experiments. If scaling requirements for miscible displacements could be relaxed while accurate simulation of essential displacement mechanisms is maintained, the utility of model studies would be greatly enhanced. The purpose of the work reported herein was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascer tain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. These studies were performed with completely miscible systems in linear, horizontal models packed with unconsolidated media. From the experimental results, a set of relaxed scaling criteria was formulated which allows the requirements of geometric similarity and equality of the ratio of viscous to gravity forces to be omitted for specified conditions. The relaxed criteria are valid whether transverse mixing is by molecular diffusion or by convective dispersion. Correlations which permit prediction of vertical sweep efficiencies in linear, horizontal reservoirs were developed from the experimental data when transverse mixing is by molecular diffusion. These same correlations may be used when transverse mixing is by convective dispersion if an empirically defined, effective, transverse dispersion coefficient is used in the description of the mixing process. The effective transverse dispersion coefficient correlation essentially duplicates the dispersion coefficient correlation for equal-viscosity, equal-density fluid systems. Experimental values for the effective transverse dispersion coefficient can be measured readily. INTRODUCTION One of the most effective methods for evaluation of miscible-displacement oil-recovery processes is that of displacements in laboratory models scaled to simulate reservoir conditions. For these laboratory studies to be meaningful, however, the essential displacement mechanisms affecting reservoir performance must be accurately simulated. Since the performance of a miscible flood in horizontal reservoirs, or in dipping reservoirs at high rates, can be significantly affected by transverse mixing of solvent and oil, this mechanism must be considered in the design of laboratory experiments. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long experiment times. This difficulty seriously limits the utility of laboratory model studies. Craig,et al,1 demonstrated that geometric similarity is not required when mixing is unimportant. Their experimental data indicate, for the cases studied, that the displacement is sufficiently characterized by scaling the ratio of viscous-to-gravitational forces. This work suggests that relaxation of the requirement of geometric similarity and, possibly, other criteria might also be permissible when mixing is important, provided suitable groups describing the mixing process are scaled. The purpose of the work reported here was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascertain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. Consequently, laboratory investigations were made of the dependence of recovery on dispersion and other variables,

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

COLLOQUIUM PRACTICAL APPLICATIONS OF INSTRUMENTATION IN THE MINING AND METALLURGICAL INDUSTRIES Rapporteur: J. Laschinger A colloquium and general meeting of the Institute held jointly with the Instrument and Control Society of Southern Africa at Kelvin House, Johannesburg on 18th October, 1972, had as its theme "Practical Applications of Instrumentation in the Mining and Metallurgical Industries" Dr J. P. Hugo (President) was in the chair and about 200 members and visitors were present.