Search Documents

By Mohamed A. Eliwah

This paper deals with the determination of hydraulic conductivity of the coastal coralline limestone aquifer of Jeddah, Saudi Arabia. This coastal area has witnessed urban development and establishment of towers which requires deep foundations, excavation and dewatering of huge quantities of unconfined groundwater. It is occupied with successive layers of soft detrital and consolidated massive cavernous coralline limestone of the Quaternary age. These layers are encountered at a depth of 1.5m and extend for more than 100m. Hydraulic conductivity values were obtained by analyzing the pumping tests data under steady and transient state conditions. Hydraulic conductivity values help in selecting the proper and safe dewatering system, as well as determination of discharge rates and quantities of groundwater to be withdrawn. Test results obtained from two surveyed sites showed that the values of hydraulic conductivity are greatly variable. It ranges between 118.1 and 1559.6 m/day at the first site, whereas at the second one it ranges between 94.6 and 350 m/day. These high values are attributed to the cavernous nature of the water-bearing formation. Jeddah city could be divided into three different dewatering zones extending from north to south parallel to the coast line. Well point dewatering system could be applied in the first zone while ditches and sumps are the most suitable dewatering method in the second and third zones. Dewatering using deep wells in such highly permeable formation will require withdrawal of huge quantities of water which will be accompanied by washing out fine sediment filling the cavities in the surrounding areas. This will badly affect the nearby buildings through settlement, crakes and other structural damages. Therefore, construction of grouting plug/blanket with thickness of 3.0 m at a depth of 20.0 m is recommended. This depth will be enough to support the plug against the hydrostatic pressure. Moreover, it is highly recommended to transfer the site into closed box, by using diaphragm walls or secant bored piles.

By Kathleen Kowalski-Trakofler, Edward Barrett

Problem: It is estimated that 5 to 10 arc flash explosions occur in electric equipment every day in the United States. In the mining industry the largest single injury category of electrical injuries are caused by non-contact electrical arcs. Method: This investigation progressed in two phases: (a) 836 Mine Safety and Health Administration (MSHA) reports of electric arcing incidents that occurred over a period of 11 years were reviewed, and (b) personal interviews were conducted with 32 individuals. A theoretical Safe Job Performance Model guided the study. Results: Behavioral dimensions were identified and included the effect of worker experience, judgment and decision-making ability, behavioral and organizational controls, and safety culture. Summary: The National Institute for Occupational Safety and Health (NIOSH) conducted an investigation of behavioral components associated with arc flash incidents and developed recommendations for interventions based on findings. Impact on Industry: This study fills a vacuum in electrical training with a focus on the organizational and behavioral aspects of arc flash incidents. There search is cross-cutting in its scope, in that the results apply not only to mining and construction, but many other industries employing electricians. Although the majority of mine electrical injuries are the results of burns from electrical arcs, few miners are aware that such a hazard exists. A safety training program, which includes a video and an instructor's discussion guide, was developed for electricians based on this study's findings. “Arc Flash Awareness” was released in 2007 (DHHS NIOSH PublicationNo.2007-116D) and is available through1-800 CDC-INFO. Phone:1-800232-4636 or email cdcinfo@cdc.gov. It is also available from MSHA at MSHADistribution@dol.gov or 304-256-3257 (DVD-576). Private industry is producing Portuguese and Spanish language translations.

This review provides a new and comprehensive summary on studying colloidal interactions encountered in mineral processing with representative examples for critical information, which are of great scientific and practical importance. Colloidal interactions play a vital role in mineral processing, including grinding, physical separation (particularly flotation), dewatering and tailings management (Fig. 1). Despite great energy input in comminution to liberate valuables from gangues, hetero-coagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. The importance of colloidal interactions is becoming increasingly significant as we process ever more finely disseminated low-grade ores as a result of inevitable depletion of high-grade ore deposits. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. 

The U.S. Code of Federal Regulations (Title 30) requires that a methane monitor be placed on every mining machine to continuously observe and record methane levels at the face. The monitor must provide a warning whenever methane levels are 1.0 percent or higher. An effective monitoring system will indicate a methane concentration of 1.0 percent on the mining machine before methane levels at the mining face reach 5.0 percent. Where the methane monitor is located on the mining machine is one of the most important factors that determines how effectively face methane levels can be predicted. Any change in the sampling location will result in a change in measured methane concentration. To protect the methanometer, it is usually located on the cutting boom at least 1 to 1.8 m (3 to 6 ft) outby the front cutting bits. A face ventilation system using blowing tubing was simulated in a full-scale test facility. Methane released from the face area was monitored at multiple locations on a model mining machine as well as locations near the face. Based on the relationship between concentrations measured on the machine and at the face, criteria were developed for selecting the best machine locations for monitoring methane. Recommendations are given for revising methane action levels for alternative sampling locations.

By W. P. Blake

Forging under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various park of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By George Asmus

Closed front, or open front for blast-furnaces, has been for a number of years a much discussed question among the furnace-men in every country where iron is made. As blast-furnaces are costly structures, and as the whole question is one of economy, I hope to be excused for entering a little into details. The "fore-hearth" is a prolonged opening in the lowest part of the hearth, from two to three feet wide, four to six feet long, and two to three feet high. It is a more or less fire-proof box, cooler than

By R. P. Rothwell

THE first difficulty mentioned is that in some instances two or more beds of coal separated by sandstone or slate rocks of considerable thickness in one part of a basin, are found running together in another part. Of course, we may happen to strike first the part of the basin where there is but a single seam, and in this case the bed would appear 60 divide into two or more branches within a short, distance. Such cases are not rare in the anthracite coal-fields. I would suggest as an explanation of this phenomenon the gradual sinking of the peat-marsh-the embryo coal-bed-on one side, and the moving forward of the marsh, so that on one part of the bed the formation of peat would still be progressing, while another part, being under water, would be covered with mud and sand. Thus we have different portions of the same bed of different ages. Now if the sinking of the marsh be stopped for a time, the bed will become thicker in the portions left exposed, and if the sinking now changes in direction, so that the part that had previously gone down commences to rise, we should have the phenomenon of a bed, continuous throughout, with one portion overlying another, and separated from it by rock strata. These are exactly the conditions observed in splitting beds. While one side of the lake is sinking, and the peat marsh moving on in that direction, the other side may be rising,

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By K. E. Brown, J. P. Brill, T. C. Doerr

A wide range of intermittent gas-lift tests way conducted in a 1,500-ft experimental well through 11/4- and 11/2-in, nominal size tubing. The well was equipped with two gas-lift valves, four Maihak electronic pressure transmitters and surface facilities to measure casing and tubing pressures, temperature, liquid production and the rate and volume of gas injected. For each tubing size, tests were conducted varying the slug length, gas volume injected and liquid viscosity and surface tension. From these tests, an empirical "fallback" or liquid loss correlation has been developed. No general fallback correlation could be obtained, and the correlation is presented in the form of one curve for each slug length of a given liquid and lubing size. A conceptual model has been developed which combines the fallback correlation with equarions which govern liquid slug pow. A mathematical simulation of the model in the form of a digital computer program is used to calculate total recovery, gas volume used and clearance time for a given test. Tubing pressures at the gas-lift valve and at the gm-slug interface are calculated as a function of time. Tubing pressures at the surface during slug clearance ore also calculated. The results compare favorably with the test data and verify the conceptual model. The extent to which the model can be used for other tubing sizes, depths, liquids and gas-lift valves can only be determined with additional experimental data. Data are also necessary so that a fallback curve can be constructed for the particular test conditions studied. INTRODUCTION The flow of liquid slugs in vertical conduits has long been an established production method in the petroleum industry. Under the name "intermittent gas lift", many advances have been made in engineering design. However, the unsteady-state nature of liquid slug flow has discouraged attempts to describe the problem analytically. The result has been that intermittent gas lift is dominated by rules-of-thumb engineering practices developed over many years. The advent of slim-hole completions has increased the demand for a more rigorous solution to the intermittent problem. Small-diameter conduits offer more frictional per intermittent cycle. Small-diameter conduits are defined to be 1%-in. nominal size tubing or smaller. When oil is produced from the reservoir in which it is found, and transported to surface tanks by intermittent gas lift, three separate flow stages are encountered: flow of the fluids to the wellbore through a porous medium, vertical flow of a liquid slug from the point of gas injection to the surface, and horizontal flow of the liquid slug through the surface flowlines from the wellhead to the surface tanks. The three stages are depicted schematically in Fig. 1. The present study deals with liquid slug flow in both the vertical and horizontal conduits, ending when the bottom of the liquid slug reaches the surface. Due to the large number of variables involved, the analytical study of intermittent gas lift is extremely complex. The possibility of flow regimes other than slug type, the nature of the force fields acting on the system, the interfacial instabilities involved, the varying operational principles of existing gas-lift valves and the complete unsteady-state nature of the physical phenomena occurring in an intermittent gas-lift cycle relate some of the difficulties encountered.

By G. H. Billings

There exists an unconfirmed opinion among many ironmasters that the combination of a small quantity of manganese, chromium, titanium, tungsten, aluminium, nickel, and some of the metalloids with iron has a beneficial effect upon the quality. And the impression prevails in some localities that the excellence of steel greatly depends upon the influence of some of these elements. Brit as the recorded experiments are so meagrely described, and made under such various conditions, the student in search of information upon the subject is somewhat bewildered by the contradiction of the opinions expressed. Observing some interesting phenomena while experimenting with an alloy of iron, copper, and nickel, I was led to determine the effect of some of the metals upon iron as free from contamination by other elements as it is possible to procure in practice, in order that the result of an alloy of an individual metal with iron might be more closely studied; for it is almost an impossibility to determine the influence of a small amount of one element upon a metal combined with a large amount of another, and the mere presence of another sometimes makes this difficult. And as most of the experiments recorded upon this subject have been made with iron containing sufficient carbon and other elements to interfere with the effect of that metal the influence of which it was desired to observe, I have endeavored to avoid these sources of error as far as practicable. In determining the specific gravity of the alloys in these ex-

The locality from where these specimens come is distant about 12 miles due south from the township of Bingara New South Wales, and is known locally as Carney's Reef, Barrack's Creek, Top Bingara. The formation traverses the western side of a serpentine spur from the main range, which runs through the country from the other side of Tamworth to Inverell, in the New England District. It has a due north and south trend, with an easterly underlay slightly out of the vertical. The formation has been opened up at different points for a distance of over two miles, and each place showing gold in the stone, and no place more than three to four chlins apart, the whole distance along the line of Reef being leased. The formation varies in thickness, the smallest being about 1 foot and the widest about 10 feet. The following is a list of properties, and description of work done on them at present. First south, and about one and a half miles from Hanion Brothers' old BalIarat claim due north, Court and patty hold a tenacre lease. The formation outcrops near the south boundary, and gold is obtainable in the stone. In the centre of the lease a costeen pit has cut the capping, which shows gold, and about two chains from the north boundary another one cuts the capping, also showing gold. The reef averages, where exposed on this property, 3 feet wide.

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate

By C. R. McEwen

This paper presents a technique for calculating the original amount of hydrocarbon in place in a petroleum reservoir, and for determining the constants characterizing the aquifer performance, based on pressure-production data. A method for doing this based on a least-squares line-fitting computationwus proposed by vanEverdingen,Timmerman andMcMahon in 1953. We found that their method would not work when there is error in the reservoir pressure data — even moderate error. The technique presented here appears to give reasonable answers when pressure data are uncertain to the degree expected in reservoir pressure determinations. The major change introduced in the present analysis is to limit the least-squares line-fitting to yield only one constant— the amount of hydrocarbon in place. The water-influx constant is then taken as proportional to the oil (or gas) in place. The constant of proportionality can be computed from estimates of effective compressibility and reservoir water saturation. It is also pointed out that the commonly used least-squares analysis assumes all of the uncertainty to be in the dependent variable. The material balance should be arranged so that this condition is fulfilled if correct inferences are to be made from statistical calculations. Examples are shown of the application of the new technique to gas reservoirs—both hypothetical and real—and to the oil-reservoir example of van Ever-dingen, Timmerman and McMahon. INTRODUCTION The amount of hydrocarbon originally in place in a petroleum resenroir can be estimated by means of the material-balance calculation. Simultaneous observations of pressure and amounts of produced fluids are required, together with the PVT data applicable to the reservoir fluids. If water encroachment is occurring, it is desirable to try to infer the behavior of the aquifer, as well as the original hydrocarbon in place, from the pressure-production data. This imposes additional demands on the method of calculation, and uncertainty in the data can result in large uncertainty in the answer. In addition, if the size of a gas cap is to be established, the whole problem becomes indeterminate, as pointed out by Woods and Muskat.1 Brownscombe and Collins2 simulated a gas reservoir and its aquifer on a reservoir analyzer and derived quantitative information on the effect of uncertainty in pressure and aquifer permeability on computed gas in place. Among the various techniques of estimating the performance of an aquifer, the method of van Ever-dingen and Hurst? based on compressible flow theory, seems to have been the most generally successful (see Ref. 4, for example). In this paper we shall confine ourselves to their representation of the aquifer. In 1953,' van Everdingen, Timmerman and McMahon5 introduced a statistical technique for deriving the amount of oil originally in place and the parameters which describe the aquifer. (We shall refer to this technique as the "VTM method'', as suggested by Mueller.6) Their example reservoir had no gas cap. It has been our experience that the VTM method gives a reasonable answer when the data are very accurate, but that inaccuracy (particularly in pressure) can cause the method to break down. The effect was first observed in gas reservoirs, but has since been seen in oil reservoirs also. In this paper we present another statistical method which has been successful in achieving a reasonable answer where the VTM method has failed. In the new method, one less parameter is derived from material-balance computations. It is assumed that values can be established for effective compressibility in the aquifer and reservoir water saturation independently of the material-balance calculation. The water-influx constant can then be obtained from these data and the quantity of hydrocarbon in place.

By Denis Shishin

The pyrometallurgical production and recycling of non-ferrous metals involves the use of complex feed stocks, having awide range of chemical compositions from sources that include mineral sulphide concentrates, high value obsolete materials and process wastes. The commercial viabilities of these operations hinge on the ability to extract value from these materials. Increasingly, modern computer-based tools are used to describe and predict process outcomes, including mass and heat balances, the partitioning of elements and phase equilibria. At the heart of these predictive tools are thermodynamic databases that describe the fundamental chemical properties of a system and all the components present. A comprehensive research program has been established to develop an accurate, self-consistent thermodynamic database describing all gas-slag-matte-metal-speiss-solid phases in the system Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Sb-Sn-Ag-Au). The database can be used in conjunction with the FactSage computer platform. The accuracy of the database and its application to industrial practice is demonstrated.

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By P. B. Baxendell

The appraial of producing properties and profitability ntzalysis of a proposed capital expenditure are based on the same principles. In both problems a projection of future cash income is. cornpared to one or more capital expenditures. Several different methods have been in use either to compute a price to obtain a given earning power on the investment or to compute the earning power which will result from a given capital expenditure. One of these, the "Average Annual Rate of Return" method, computes in a simple manner the ratio of the present value of the future earnings after amortization to the present value of the undepreciated balances of the investment over the life of a project. This method, not well known generally, appears to have some rather unique advantages in reducing the computation work required, eliminating trial-and-error solutions, and providing a more accurate answer when applied to oil industry investments subject to the unit-of-production basis of amortization. Its derivation is given and its versatility demonstrated in the solution of certain everyday investment problems. A number of charts, useful in applying this method to profitability analysis and appraisal work, are provided. The current trend in the market values of producing properties is shown. INTRODUCTION Making sound capital expenditure decisions requires an objective means of measuring the productivity of individual investment proposals. Since the best measure of the economic worth of such proposals is their ability to produce profits, it is common practice to grade proposed capital expenditures according to their annual earning power as a percentage of the outstanding capital. The same principles which govern the determination of the rate of return of proposed capital expenditures also apply generally to the problem of determining the appraisal value or purchase price of income-producing oil and gas properties. Both problems are of prime importance in the producing phase of the oil business, where management is faced daily with decisions to drill or not to drill certain development wells, or with the determination of the appraisal value of producing properties. The common feature in both problems is that a projection of future cash income is compared with a known or estimated capital investment to determine itsiearning power or annual rate of return. In the case of development drilling, the cost of the proposed well can usually be estimated with a fair degree of accuracy and the problem consists of finding the rate of return on the invested capital. In the case of appraising producing properties, on the other hand, the desired rate of return is usually known in advance and the problem consists of determining the purchase price which, for the given income projection, results in the fequired rate of return. Certain accounting procedures common to the oil and gas producing business make these two problems and their solutions somewhat different from corresponding problems in other industries, and, in certain ways, simpler. The main difference is in the amortization policy which, for oil and gas production, is frequently on a unit-of-production basis, compared to the amortization on a time basis used in many other industries. The purpose of this paper is to discuss briefly the various methods currently in use for the measurement of productivity of invested capital in producing properties and, in more detail, the derivation and application of what will be called the "Average Annual Rate of Return Method". This rather interesting and not too well known method has some very definite advantages in the solution of many problems common to the oil industry. For the sake of simplicity, federal income tax considerations have been disregarded in the examples used, since they do not affect the principles involved. The use of the production payment route in the sale or purchase of producing properties, which has been amply covered in many other publications, has also not been included in this analysis. METHODS FOK MEASUKING THE EARNING POWER OF INVESTED CAPITAL, Of the many different methods used to measure the earning power of invested capital, four are applicable to oil or gas production ventures. Depending on whether these four methods utilize one or two interest rates, and whether a fixed amortization pattern is used, they may be classified as follows.

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.