Search Documents

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William F. Lawrence

INTRODUCTION Cleaning fine coal sizes utilizing air currents in machines as the primary separating medium is called dry concentration or pneumatic cleaning. In 1947 approximately 18 million tons (16.38 million mt) of bituminous coal were cleaned by air machines; in 1965, 25.4 million tons (23.1 14 million mt); but in 1975, only 7 million tons (6.37 million mt). Table 11-1 shows the tonnages cleaned of bituminous coal and lignite in the United States by various types of equipment from 1938-1963. Table 11-2 shows only tonnages cleaned by pneumatic methods from 1964-1975. The decrease in tonnage to approximately 7 million tons (6.3 million mt) is due to a higher moisture content in the mined coal and the greater difficulty in cleaning the coal by air. There also was a definite trend to load raw coal at the mines, especially the slack which is the most expensive to clean due to the dewatering and drying requirements. While there have not been any applications of pneumatic cleaning in the anthracite field, its use has not been fully explored. The same is true for lignite and subbituminous coals.

Jan 1, 1979

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By V. Annamalai, J. B. Hiskey

The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol- 1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol- 1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 1, 1979

Jan 1, 1979

By J. D. Miller

The authors have summarized the state-of-the-art in the kaolin clay industry very well. In some instances the problems which they have identified are common to all fine particle separations and in other cases the problems are unique to the kaolin clay industry itself. General areas of research which may be common to other systems and which deserve continued investigation at a higher level of support include: 1) Establishment of the relationship between flotation response and clay structure/composition. 2) Determination of temperature effects in the separation of fine particles. 3) Evaluation of the effect of bubble size on the quality of fine particle separation. The first two areas would require basic surface chemistry studies including microflotation, electrokinetics, adsorption density measurements, and microcalorimetry. The last area would be oriented toward the mechanics of bubble-particle attachment. Regarding the first area, the authors alluded to this research need by commenting on the variation in separation observed from one deposit to another. It seems that a detailed study characterizing the flotation response of various clay types with respect to structure and compositional features would be of considerable value. For example, I understand, that D. W. Fuerstenau&apos;s group has recently been successful in characterization, with respect to structure, of some silicate mineral types--chain, sheet and framework silicates. A similar study should be initiated in which the flotation behavior of various clay minerals kaolinite, halloysite, montmorillonite

Jan 1, 1979

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By D. M. Doyle

"A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc. over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study 11rogresses through monthly, daily and finally, into quarter hourly data, the variations become more evident and most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program.The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Sudbury Operations, the material and control equipment, the commitment, the new energy accounting practices and lastly, the policies. Examples of successful energy conservation endeavors include automatic peal electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailmen: of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and if necessary, immediate reporting of energy and energy per unit of production information. The program so reported at Falconbridge’s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0 million dollar annual energy account."

Jan 1, 1979

Bowen, R., and Gunatilaka, A. Copper, its Geology and economics. London, Applied Science Publishers, 1977. Miller, D. S. Internal flow systems. (Volume 4 in the BHRA Fluid Engineering Series). 1978. 288 pp. £21,50. MACH 80 The Machine Tool Trades Association of Great Britain (M.T.T.A.) announce that MACH 80 - The International Machine Tool Exhibition - will take place from Tuesday, 22nd April, to Friday, 2nd May, 1980, at the National Exhibition Centre, Birmingham.

Jan 1, 1979

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979

By J. C. Kerkering, J. C. Franklin, T. O. Meyer, R. W. McKibbin

A continuous survey of radon gas was made in two interconnecting stopes in a southwestern U. S. uranium mine to determine how the various phases of the mining cycle affected the radon concentration. The radon was monitored continuously with five detectors. One detector monitored the intake air, one the exhaust air, and three the stope air. The radon concentrations present during slushing, blasting, and exhaust fan shutoff were compared with concentrations on a nonwork day as a base level. Inside the stope, the radon concentration increased about 40% during slushing and 425% after blasting. Intake air radon increased 1600% and the stope air increased 550% while the surface exhaust fan was off.

Jan 1, 1979

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed- torque characteristics to provide an optimum from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 1, 1979

By Conrad W. Stellar, John L. Paynich

Design/Build concept that provides for earliest possible completion and lowest cost is presented. Elements of the program include: joint cooperation between owner, designer and builder; schedule construction sequence; and a line budget. Benefits over lump sum contracts are reviewed.

Jan 1, 1979

By M. L. Jeremic

Observations of ground behavior in mining the Choka Dulkan ore body have been described. Ore recovery was limited to approximately 60% because unconsolidated hydraulic fill did not permit either the widening of stope spans nor secondary ore recovery from pillars. Stope undercutting induced high stress concentrations. However, as extraction progressed, ground conditions improved but before extraction was complete they deteriorated again. After completion of a stope, the remnant rib and crown pillars continued to be deformed by other stresses for some time.

Jan 1, 1979

By L. Alan Weakly

The Bureau of Mines has pursued a program of research on mine illumination that has defined the coal miner&apos;s illumination needs. St. Joe Minerals Corporation, recognizing the need for improving the illumination of the working place in their mines, entered into a cooperative research agreement with the Bureau of Mines to utilize the Bureau’s expertise in this field. Some similarity in the environment, in which coal and hard rock miners work, has allowed the application of developed coal mine illumination technology and equipment to be utilized in hard rock, room and pillar mines.

Jan 1, 1979

By Diómedes Sarmiento

Centromin is a Mining Company owned by the peruvian government. It&apos;s considered as one of the major mining and metallurgical center in Latin America. The main operations of the Company are: Mining, Concentration, Smelting and Refining of several metals (Figure 1). At present, dentromin operates with six mining units: Cerro de Pasco, Morococha, Casapalca, San Cristobal, Yauricocha and Cobriza; which are located in the Central part of the country between 2 100 m and up to 4 800 m above sea level. The installed capacity of concentration all together ranges about 14 000 tons per day. There&apos;s also a metallurgical plant in La Oroya with a production capacity of 220 000 tons per year of refined metal. The production of the Company is diversified in twenty two (22) final pro- ducts, whose major productions are : copper, lead, zinc, silver, gold, tungg ten and bismuth. The minor products are: arsenic, antimony, cadmiun, teluriun, sulphuric acid, indium, selenium, etc.

Jan 1, 1979

Exploration for uranium in Australia has so far discovered reserves equal to 17.5% of the Western World&apos;s. The Australian uranium industry, when fully developed, will be one of the largest producers and possibly the largest exporter in the world. The world&apos;s nuclear industry is young, rapidly developing in size and technology and is subject to more social, political and regulatory controls than any other industry. This paper considers the probable development of Australia&apos;s uranium industry against a background of normal commercial parameters together with other factors which are peculiar to the nuclear industry. As the theme of this conference is "Australia&apos;s role in the World Mineral Indus- try" this paper concentrates on the commercial and practical aspects associated with the development of Australia&apos;s uranium resources in a world context.

Jan 1, 1979

By H. O. Harju

Inco acquired majority interest in the nickel laterite concessions in eastern Guatemala in 1960 and, through its subsidiary Exmibal, extensively explored the deposits until 1965 to define the site for project development on the north shore of Lake Izabal. This paper outlines the exploration methods used to evaluate the Guatemalan laterite deposits.

Jan 1, 1979

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979