Search Documents

By Thomas H. Holley

This presentation will describe the underground excavation at the Bad Creek Pump Storage project. It consists of approximately 3,650 m of various size tunnels ranging from 4.2 m to 9.0 m finished diameter, a powerhouse cavern 45 m high by 135 m long by 22.5 m wide, and 422 m of 9 m diameter shaft. A total of 350,000 m of rock will be excavated, hauled, and placed in a submerged wier. Temporary rock support consisting of shotcrete and/or rockbolts is installed as required.

Jan 1, 1987

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By Flloyd J. M

A continuous oxygen probe,incorporating a SIRO2 solid electrolyte oxygen sensor which measured the oxygen potential of a small volume of gas enclosed above the melt's surface,was constructed and tested. The oxygen potential of iron-silicate slags in equilibrium with solid iron in the temperature range 1250 to 1300¦C were measured continuously for tests of up to 40 hours duration. Results were in agreement with those of previous workers using gas equilibration techniques. Tests on non- iron buffered slags proved unsuccessful due to corrosion of the probe's component in contact with the slag and an alternative material is Required.

Jan 1, 1987

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By Frank A. Peters

This description of process evaluation techniques used by the Bureau of Mines for studying proposed processing techniques has been prepared to provide those interested in using these studies with an understanding of the methodology. The methods used for preparing both capital and operating cost estimates are described. Each step in preparing the evaluations is described. Types of equipment costs are shown and factors used in the estimates are defined. Uses of the estimates are suggested and several examples are included. The accuracy of various types of estimates is discussed, along with an explanation of the reason for selecting the type used in the Bureau's process evaluation studies.

Jan 1, 1987

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By L. C. Woollacott

A computer-aid is described that is designed to calculate steady-state material balances for ore-dressing circuits. The program determines the material balance from a specification of the process condition. No mathematical models or data adjustment techniques are employed. As such the program complements existing simulation and material balance 'smoothing' packages. The process condition is specified using performance indicators. These are significant parameters in the industry with which all practising mineral processors are very familiar. The program employs an equation-oriented technique for material balancing and so has had to deal with the difficulties peculiar to that approach.

Jan 1, 1987

By Roger Cabos

El presente texto señala la necesidad de estudios microscópicos determinativos y cuantitativos como complemento de los análisis químicos, de forma que se explore la posiblidad de beneficiar el mineral oxidado por métodos convencionales.

Jan 1, 1987

By Philip U. Santacroce, James H. Meinholz

One-half of the $607 million Conveyance construction portion of the Milwaukee Metropolitan Sewerage District's Water Pollution Abatement Program is completed or under contract. 12,200 m (7.5 miles) of tunnel boring machine (TBM) driven rock tunnel from 2.5 m (8.0 ft) to 9.9 m (32.3 ft) diameter has been completed. This paper presents a review of TBM performance and a discussion of the pertinent geological conditions of the area.

Jan 1, 1987

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By Dean D. Turner

Exploration geochemistry requires computer processing for quick and efficient reduction and interpretation. An easy to use microcomputer based geologic workstation fulfills this need and allows the geologist to independently process geochemical data. Functions necessary for geochemical data processing are: 1)Digitizing; 2)Communications; 3)Data base management; 4)Statistical analysis; 5)Mapping analysis; and 6)General purpose applications (ie: word processing). A geologic workstation that can perform these tasks will yield significant advantages in processing and interpreting geochemical data.

Jan 1, 1987

By Richard H. Adams

INTRODUCTION With the discovery and depletion over the years of near surface ore bodies, exploration targets are tending to be at greater depth or overlain by various types of overburden which in some cases extends to considerable depth or is heavily water bearing. Access to these types of deposits for exploration and development often requires vertical shafts. This paper discusses the concept of small shaft engineering and construction, primarily for underground exploration but also for use as a low tonnage production facility or for mine ventilation. The option of a small shaft may be attractive in a number of cases, some of which are: The underground exploration of a deposit at depth where minimal expenditure is desirable until the potential of the deposit has been determined. The exploration shaft in many cases later serves as a ventilation way and second means of egress. Production of ore in a small tonnage/high-grade operation where decline access is impractical. For ventilation where other types of openings are impractical or would delay start-up of mine operations.

Jan 1, 1987

By Walker G. S, Sparrow G. J

Dissolution of S02 into water-acetone mixtures results in the formation of 2-hydroxy-2-propane sulphonic acid. The pH, or acid strength, of water-carbonyl-S02 mix- tures can be controlled by varying the concen- tration of the carbonyl compound or the rate at which S02 is added to the water-carbonyl mixture during a reaction. The ease with which the acid strength of these mixtures can be controlled means that they have significant potential for use as a selective lixiviant. We have used water-acetone-S02 mixtures to selectively dissolve phosphate minerals in Christmas Island and Duchess phosphate ores and also uranium minerals in Yeelirrie uranium ore and Olympic Dam copper concentrate.

Jan 1, 1987

By Waghorn EP, Gleeson HB

The Loy Yang Optr, Cut is a brown coal mine bring developed in the Latrobe Valley region located some 160 kin south-east of Melbourne, Victoria. The mine has been designed to supply a mine mouth power station at a rate that will rise to 32 million tonnes per year by the mid 1990's. Continuous mining metnuds are employed using bucket Whtel excav- ators and conveyors. This paper describes the basis of the design of the Loy Yang continuous mining system ano cne experience of four years of initial operation.

Jan 1, 1987

By Reinhard Gnilsen

Ground pillar control in soil and weak rock often represents a critical and sometimes a determining factor for mined underground civil structures. A concept is desirable that minimizes the restrictions possibly imposed by pillar control requirements on geometrical tunnel characteristics and on the mining operation itself. Conventional concepts are discussed and an alternative concept is introduced. This concept reduces pillar control requirements to ground control measures required with "regular" tunnels. The conventional model of pillar mechanics with potential yielding of a ground body in more than one direction, is then avoided. Due to the complexity of pillar mechanics, the level of engineered design furnished to the contractor is crucial to optimizing ground pillar control. Conventional versus alternative contractual arrangements for pillar control are described and their important role is illustrated. The concept introduced relates to principles inherent to the New Austrian Tunneling Method (NATM). However, tunnel projects using other mining concepts can employ alternative ground pillar control principles as well, if certain criteria are observed. Case histories in the United States and abroad are presented and the impacts from different concepts of ground pillar control are illustrated. The paper concludes by analyzing concept characteristics that can infer monetary impacts on both the owner and the contractor.

Jan 1, 1987

By M. M. Oosterveld

Diamonds are mined from ancient raised beach deposits in southern Namibia where complex geological controls have resulted in patchy diamond distribution, largely related to irregularities (trapsites) in the bedrock. The distribution of the number of diamonds per sample is a discrete, reverse- J shape distribution which can be characterized by two parameters. These parameters have been transformed into a Beta and Theta Contribution which can be interpreted as reflecting the 'quantity' and 'quality' of the trapsites. The relationship of statistical parameters, obtained during the sampling of an ore deposit, to the geology of the deposit is an important element of ore reserve estimation. The large-scale regional trends in the contributions have been explained in terms of the geology.

Jan 1, 1987

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By P. H. Lu, M. J. DeMarco, J. R. Koehler

Beginning in late 1985 and continuing through 1987, US Bureau of Mines personnel investigated longwall chain pillar and entry design in two and three-entry gateroad systems at a deep underground coal mine in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in rooffalls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1987